Question about 2005 Mitsubishi Outlander

Open Question

How do I change the power steering pressure hose on 2005 mitsubishi outlander AWD

Existing **** is leaking. And there is not enough room to pull out the hose. Thanks.

Posted by Anonymous on


6 Suggested Answers


6ya staff

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Justin Case

  • 1498 Answers

SOURCE: serpentine belt replacement

Hi Paul,

The routing diagram is under the hood.

  • Get a 14mm or 9/16" socket and a long handled ratchet or breaker bar.
  • Get the belt around all the pulleys except the A/C compressor or Alternator.
  • The tensioner pulley is near the Alternator toward the center of the engine. It's on a spring loaded arm. Get your socket on the center nut of this pulley.
  • Slowly pull the ratchet toward the center of the engine. The pulley will pivot on the arm allowing you to get the belt on the final pulley.
  • Slowly release the tension.
  • You're done

Posted on Dec 14, 2008



  • 362 Answers

SOURCE: Cam Belt on Outlander 2.4 litre Petrol - 2004

The vehicle has a belt and should be changed every 60,000 miles.

Posted on Jan 31, 2009


  • 333 Answers

SOURCE: mitsubishi outlander cooling fans not operating

There is a Recall to replace your cooling fan module because of this concern.

Open your hood and look at the black box bolted to your radiator fan by the battery. If it does not have a green dot on it, you have not had the replacement fan module installed.

Contact your local dealer with your VIN handy to verify the recall has not been done and to schedule an appointment.

If the recall has been done, verify if you have power coming out of the module to the fans, as the fans do burn out eventually.... but rarely both at once.

Posted on Sep 10, 2009


  • 333 Answers

SOURCE: how do you reset change oil light on mitsubishi outlander

Turn the key off.

Press the "Info" button on the left of the dash cluster until your maintenance miles/months screen is displayed.

Press and hold the "info" button until the maintenance screen begins flashing.

Release the "info" button and then push and hold it it for one second.

Your Maintenance intervals should reset to +6 months and +7500 miles since the last interval amount.

Note that if you have not reset it for more than one interval, you may need to do it more than once. If you have not done it for many intervals, you may need to have it reset with the scantool at a dealer, as I have run into a handful of vehicles that the oil change reminder locked up after 3-4 "intervals" were skipped/not reset.

Posted on Sep 11, 2009


  • 333 Answers

SOURCE: need mitsubishi outlander 2005 drive belt diagram

Here you go, please be sure to rate me if you find this answer useful!

Posted on Oct 25, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Want to replace octopus hose on holden vectra 2001 2.2 ltr

this is the part ..
looks like one of the harder diy jobs on this model
take photos as you go
you need to be able to undo all the clamps and connections
and put the hoses back in the right place

source internet
one mechanics view on the job
Spent the better part of two hours pulling this hose out of a customers car. Had to drop the alternator and starter motor to get enough room to pull it out over the gearbox. did you pull the inlet manifold or drop the alt and starter like i did?



Apr 11, 2014 | GMC Acadia Cars & Trucks

1 Answer

1989Volvo 240DL Heater hose leaking

I tink that you should chang the heater radiator

Oct 23, 2017 | 1998 Volvo S70

1 Answer

Gas leaking from the end of where the hose is clamped

either put a new clamp on or if you have a hole in the hose and have enough room. cut a little of the end off and re connect it

Aug 27, 2010 | 2005 Chrysler 300

2 Answers

Trans fluid leaking from line going into radiator can I fix this myself

most of them are hoses clamped on if is yes easy to repair, unclamp hose on both ends replace with new hose & clamps

Feb 04, 2010 | 2000 Chrysler 300M

1 Answer

1999 Porsche Carrera leaking coolant. Can't see or find the leak,not enough room underneath. It is leaking directly over the exhaust pipe. Is there a discharge hose in case of overheating that might be the...

the only coolant lines would go from your rad to engine block and lines to your tranny, what part of your exhaust is it dripping on (close to the catalytic converter,or on the tailpipe)??

Nov 19, 2009 | 2000 Porsche 911 Carrera

1 Answer

2000 honda civic changed hose but still leaking


Sep 20, 2009 | 1996 Honda Civic

4 Answers

I have a 2001 eclipse. Water leaking onto driver side of floorboard. There is so much water it is puddling.I am not sure if it is ac drain or heater core. I can't find ac drain to see if it is clear....

I recently had this repaired. As it turns out, the evaporation reservoir separated from the firewall. I was fortunate enough to have a good mechanic that completely diassembled my dash to locate the leak. He did not make up some lame diagnosis. I was unfortunate enough to have to pay for the extensive work, but it is worth it. He resealed the heater core compartment to allow the water to drain out properly. I spent many hours searching for an answer in the internet. this is the only solution that I know of.

Jul 19, 2009 | 2001 Mitsubishi Eclipse

1 Answer

Leaking alot of water /coolant

You have answered your own question almost. You will need to jack the car up and inspect everything being that its 91 camara, there is defintely enough room to inspect everything. You either have a hose leak, a radiator or water pump leak. Only inspection will find that out. Thank you,

Jun 27, 2009 | 1991 Chevrolet Camaro

1 Answer

Overheat smell

When the engine is cold, check the coolant level. if it's low, add enough to fill. Check the oil like this: Pull the dipstick out, wipe it clean, insert it back in the tube, wiggle it, pull it out and look closely. See if you spot what look like bubbles in the oil. This may indicate coolant is leaking past the head gaskets and getting burned, hence the overheating smell. Could be a leak at one of the hose fittings, or the hose itself, dripping onto hot metal parts. If it's a head gasket issue that needs to be addressed, but that's worst case. Check all the hoses and clamps, feel around for wetness, might just be a simple drip from a loose hose clamp.

Mar 06, 2009 | 1996 Chevrolet Camaro

1 Answer

Heater hose on 1989 Honda Accord

if i remember right you need to take off the air intake hose and it should give you a little more room to get at that clamp. thanks for using fixya

Aug 16, 2008 | 1989 Honda Accord 4 Door

Not finding what you are looking for?
2005 Mitsubishi Outlander Logo

Related Topics:

155 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts


Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides