2010 Ford Fusion Hybrid Logo
A
Anonymous Posted on Sep 25, 2014

What is the rumble on braking in rear of my 2010 fusion hybrid 100k miles?

1 Answer

robert wales

Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

  • Ford Master 4,977 Answers
  • Posted on Sep 25, 2014
robert wales
Ford Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Joined: Mar 01, 2011
Answers
4977
Questions
0
Helped
1332200
Points
59541

It could be the drum/rotor is warped causing the noise or the pads/shoes have gone hard or rust build up on the edges causing it as well. either way have the brakes checked for condition.

1 Related Answer

A

Anonymous

  • Posted on Apr 08, 2013

SOURCE: rear brake cailpers won't collapse on 2007 ford fusion

Open bleeder valve & push caliper piston, in as
you rotate piston to screw in parking brake

Do this by hand,only use a clamp on the front calipers

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

High beam headlight wire color 2010 Ford fusion se

usa or canada, no country told , (fail)
cars
RTM
read the manual

https://eautorepair.net/Marketing/Default.asp


wiki says (see why we can't guess where you are:)>
and lighting laws are not the same all over earth (yet)


From Wikipedia, the free encyclopedia
Jump to navigation Jump to search Ford Fusion may refer to:
0helpful
1answer

2010 ford fusion hyprid power steering went out

Power Steering - Hybrid The electric power assist steering system consists of:
  • power steering control module
  • electric motor
  • torque sensor
  • rack-and-pinion steering gear
The electric power steering system provides power steering assist to the driver by replacing the conventional hydraulic valve system with an electric motor coupled to the steering gear. The motor is controlled by an electronic control unit that senses the steering effort through the use of a torque sensor mounted between the steering column shaft and the steering gear. Steering assist is provided in proportion to the steering input effort and vehicle speed.

your best bet would be to have the ford dealer check it out !
0helpful
1answer

What does a po130 code on 2010 Ford Fusion Hybrid mean?

Possible causes
- Faulty Front Heated Oxygen Sensor Bank 1
- Front Heated Oxygen Sensor Bank 1 harness is open or shorted
- Front Heated Oxygen Sensor Bank 1 circuit poor electrical connection
- Inappropriate fuel pressure
- Faulty fuel injectors
- Intake air leaks may be faulty
- Exhaust gas leaks
Tech notes
Replacing the O2 Sensor 1 usually takes care of the problem
0helpful
1answer

2010 hybrid ford fusion the wrench symbol came on. What does it mean?

2010 Ford fusion hybrid recall/update for becm and PCM. Corrects issue. Software has to be updated
0helpful
1answer

Service advance trac light on & car won't start

Similar issue on my 2013 taurus. Died on me one day and wouldn't even crank. Advancetrac Service, 911 assist unavailable, sometimes braking system faults and just about every light on the dash illuminated. No codes. The problem was the Run/Start relay (Start/Run??). Swapped it with the windshield wiper relay to verify. Car started but the wipers didn't work. Replaced the Relay for $25 from AutoZone.
0helpful
1answer

2010 fusion tail lights won't turn off

I suggest check brake switch, underdash, top back side brake pedal or some short/ground there.
1helpful
1answer

2010 ford fusion compass trouble with east and west even after cal per manual info going east show west. n-s fine

Might be a problem with the compass module itself. Since the car is new, and still under warranty, take it to the dealer. They will fix it free of charge. Trying to repair it yourself may void the waranty.
3helpful
1answer

2010 Ford Fusion - After changing the oil, how do I extinguish the oil change warning?

You use the "Setup" and "Reset" buttons in the Information Center. The sequence of button-pushing is different for Hybrid and Non-Hybrid vehicles. The sequence for your car should be outlined in your Owner's Manual.
Not finding what you are looking for?

188 views

Ask a Question

Usually answered in minutes!

Top Ford Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

xxxxxx xxx

Level 3 Expert

5117 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...