Question about 2007 Acura RDX

Open Question

How to remove tail gate panel on 2007 acura rdx

Tail gate panel

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

super_guy

  • 1986 Answers

SOURCE: RDX Front Door Panel Removal - instructions,

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1996. How do I open locked, stuck tail gate?


You can take the panel off on the inside of the tail gate, and open it by manually pulling on the linkage rods at the same time.

Dec 06, 2015 | Isuzu Rodeo Cars & Trucks

1 Answer

The tail gate release handle has disconnected from the latching system and won't open. There appears to be a cable 'floating' around in the gap.


Hopefully your talking about a truck. With a flat screwdriver on both sides you'll need another hand here you'll have to push the locks in ward but not to damage sides.after tail gate opens there should be a panel on the top inside of the gate if you have a bedliner cover on the tail gate you'll need to remove it to get to that panel.after you get that panel off .you'll be able to see why that cable came off.

Nov 27, 2015 | Cars & Trucks

1 Answer

Tail Gate open warning light will not turn off. where is the button switch on the tail gate?


Check with a multi-meter that the switch itself has a open/closed function(ohm meter setting)Hope this helps....

Feb 06, 2015 | 2005 Hyundai Getz 1.3

1 Answer

How to remove and replace tail light assembly on 2003 jeep grand cherokee. There's one screw behind the rear quarter panel to complete the removal process of the tail light assembly. How do I remove that...


There is 2 screws located on the side when you open your tail gate by the tail light. remove these 2 screws and pull the tail light out and disconnect the wire connector. Hope this helps.

Best of luck

Jun 13, 2010 | 2003 Jeep Grand Cherokee

1 Answer

I have a 1997 Ford Ranger. I can not lower the Tail Gate


I had the same issue and took the panel off. the handle is connected to 2 bars that are connected to both sides of the tail gate. One of the bars had somehow bent and came loose. All I did was straighten that bar enough to get it back into the slot on the handle, screwed a nut onto it so it couldnt pull out again. And never had a problem since.
If you look in between where the gate meets the fender , u can see the lock and push in to release the gate. Sorry , No repair manuel , I just start takin things apart

Feb 17, 2010 | 1997 Ford Ranger SuperCab

1 Answer

2004 Mercury Monterey tail gate handle came completely off. The left side's guide is in place, but the right side is retracted - hence can't just put it back in. Any ideas?


Open tail gate. Use the access square inside - pull cable to open tail gate. Remove interier panel - 2 bolts plus 2 screws (2 bolts on handle and 1 screw each side), pull remainder out of guide clips. Now have full access to locking mechanism. Identified a retaining spring had come loose sending guides to shift left (exterior point of view). Place hand in tail gate and move guides over and put spring in place to retain. verify it works and put back together. Handle is the trickiest part as the bolts have to go through the interior panel and afix to the metal tail gate.

Sep 20, 2009 | 2004 Ford Freestar

1 Answer

I need to replace the whole rear tail gate lamp assembly.


Yeah remove the inside panel to get to those bolt, they should be 10mm nut.

Aug 12, 2009 | 2008 Toyota Sienna

1 Answer

Rear wiper motor


raise up the tail gate . remove the phillip screws holding the handle or pull down strap.remove all other screws holding the rear plastic tail gate panel in place than start in one corner try to pull down on the plastic panel as it is also held in place with push style plastic clips.you can use a straight blade screw driver to start releaseing the clips.once you have the panel off you have done the hard part/ just unbolt the wiper motor and reassemble.
good luck chris

Mar 22, 2009 | 1993 Dodge Caravan

1 Answer

Chevy blazer 2w drive 2 door-rear gate wont open


you will need to try to remove the rear door panel on the tail gate or pry it away its not easy because of hidden screws the manually pull the linkage

Aug 16, 2008 | 2002 Chevrolet Blazer

2 Answers

Tail gate


I also have this problem and don't know what to do.
Marge58

Jul 04, 2008 | 1996 Jeep Grand Cherokee

Not finding what you are looking for?
2007 Acura RDX Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...