Does the turn signal switch operate wind shield wipers 2001 f 150 7 wire need diagram

It should be a short circuit or a bad relay. Good luck.

Switch is bad.

Do you know how to do electrical testing ? Here is diagnostic trouble flow chart .You will need a wiring diagram . Go to http://www.bbbind.com/free_tsb.html free wiring diagrams . You can see basic automotive trouble shooting videos on you tube if you are not familiar with this .
Wipers Low Mode Inoperative, High Mode Operates

2
Disconnect wiper motor connector C1.
Turn the ignition switch ON.
Set the wiper switch to LO.
Connect a test light from wiper motor connector C1, terminal B, to ground.
Is the test light on?
--
YES - Go to Step 6
NO - Go to Step 3

3
Inspect for a poor connection or an open in CKT 91.
Is a poor connection or an open present?
--
YES - Go to Step 4
NO - Go to Step 5

4
Repair the poor connection or the open in CKT 91.
Is the repair complete?
--
Go to Wiper/Washer System Check
--

5
Replace the wiper/washer switch. Refer to Multifunction Turn Signal Lever Replacement - On Vehicle in Steering Wheel and Column -Tilt.
Is the replacement complete?
--
Go to Wiper/Washer System Check
--

6
Connect a test light from wiper motor connector C1, terminal C, to ground.
Is the test light on?
--
YES - Go to Step 10
NO - Go to Step 7

7
Inspect for a poor connection or an open in CKT 95.
Is a poor connection or an open present?
--
Go to Step 9
Go to Step 8

8
Repair the poor connection or the open in CKT 95.
Is the repair complete?
--
Go to Wiper/Washer System Check
--

9
Replace the wiper/washer switch. Refer to Multifunction Turn Signal Lever Replacement - On Vehicle in Steering Wheel and Column -Tilt.
Is the replacement complete?
--
Go to Wiper/Washer System Check
--

10
Inspect for continuity between wiper motor connector C1, terminal A, and connector C2, terminal B, using a J39200.
Is continuity present?
--
Go to Step 12
Go to Step 11

11
Repair the open in CKT 196.
Is the repair complete?
--
Go to Wiper/Washer System Check
--

12
Inspect for a poor connection to the wiper motor at connector C1.
Is a poor connection present?
--
Go to Step 13
Go to Step 14

13
Repair the poor connection at wiper motor connector C1.
Is the repair complete?
--
Go to Wiper/Washer System Check
--

14
Replace the wiper motor. Refer to Windshield Wiper Motor Replacement .
Is the replacement complete?
--
Go to Wiper/Washer System Check
--

When the windshield wiper / washer switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the wiper motor module will continue to operate the wiper motor until the wipers reach the park position. If the ignition is turned off while the wipers are in mid-cycle, the wipers will stop immediately where they are. The wipers will park the next time the ignition is cycled to the ON position.

Schematic Reference: Wiper/Washer Schematics


1

Did you review the Wiper/Washer System Description and Operation and perform the necessary inspections?
Go to Step 2
Go to Symptoms - Wiper/Washer Systems

2

1. Turn the ignition ON.
2. Turn the windshield wiper/washer switch OFF.

Are the windshield wipers always on?
Go to Step 3
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

3

Disconnect the windshield wiper/washer switch connector.
Are the windshield wipers always on?
Go to Step 4 if yes
Go to Step 7 if no

4

1. Disconnect the windshield wiper motor connector.
2. Test the windshield wiper switch signal 1 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.

Did you find and correct the condition?
Go to Step 11
Go to Step 5

5

Test the windshield wiper switch signal 2 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 6

6

Test the windshield wiper motor high speed circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 9

7

Inspect for poor connections at the windshield wiper/washer switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 8

8

Replace the windshield wiper/washer switch. Refer to Windshield Wiper and Washer Switch Replacement - On Vehicle in Steering Wheel and Column.
Is the repair complete?
Go to Step 11
--

9

Inspect for poor connections at the windshield wiper motor. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 10

10

Replace the windshield wiper motor. Refer to Windshield Wiper Motor Replacement .
Is the repair complete?
Go to Step 11
--

11

Operate the system in order to verify the repair.
Did you correct the condition?
The Wiper / Washer System consists of the following components:
?€¢
Windshield wiper / washer switch

?€¢
Windshield wiper system module / motor

?€¢
Windshield washer fluid pump

?€¢
Windshield washer fluid level switch

?€¢
Instrument panel cluster (IPC)

?€¢
ACC 15-amp fuse

?€¢
WSW 30-amp fuse

The switch is bad or the wiper motor cover ,electronics !

1. Turn the ignition switch to RUN.
2. Turn the wiper switch to OFF.
3. Disconnect the wiper/washer switch connector C201.

Do the wipers park? yes or no ?
if yes Replace the wiper/washer switch. Refer to Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle .
if no
Measure the voltage from connector C201 (vehicle side), terminal E2, to ground with a DMM.
Does the voltage measure greater than the specified value?
1.0 V yes or no ?
Replace the wiper motor cover. Refer to Wiper Motor Cover Replacement .
Did you complete the replacement?
--
Go to Step 9
--

6

1. Reconnect the wiper/washer switch connector C201.
2. Disconnect the wiper motor connector.
3. Measure the voltage from the wiper motor connector, terminal D, to ground with a digital voltmeter.

Does the voltage measure greater than the specified value?
1.0 V
Go to Step 8
Go to Step 7

7

Replace the wiper motor cover. Refer to Wiper Motor Cover Replacement .
Did you complete the replacement?
--
Go to Step 9
--

8

Repair the short to voltage in CKT 113. Refer to Wiring Repairs in Wiring Systems.
Did you complete the repair?
--
Go to Step 9
--

9

Operate the system in order to verify the repair.
Did you correct the condition?
--
System OK
Go to Wiper/Washer System Check



if yes

Go to alldatadiy.com and buy the wiring for your vehicle. Other wise go to the junk yard and cut the plugs and wires out of an exact vehicle. This is the only two ways you will fix it. Exact diagrams or exact plugs and switches.

Sorry , no adjustment .
Wiper/Washer System Components
The Wiper / Washer System consists of the following components:
• Windshield wiper / washer switch
• Windshield wiper system module / motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR 25A fuse
Wiper / Washer System Operation
The windshield wiper motor module is part of the windshield wiper motor cover and controls the wiper motor operation. The windshield wiper motor is a 2 speed motor. Windshield wiper DELAY operation is a low speed wiper motor function with a variable delay interval between the wipe cycles. The DELAY interval is controlled through a series of resistors within the wiper / washer switch.
Park Position Operation
When the windshield wiper / washer switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the wiper motor module will continue to operate the wiper motor until the wipers reach the park position. If the ignition is turned off while the wipers are in mid-cycle, the wipers will stop immediately where they are. The wipers will park the next time the ignition is cycled to the ON position.

Do you know how to do diagnostic's ?

Wipers Blades Do Not Park
Step
Action
Yes
No
Schematic Reference: Wiper/Washer Schematics
Connector End View Reference: Wiper/Washer Connector End Views
DEFINITION: This table diagnoses the wipers operate normally but will not return to the park position when the wiper operation is cancelled.
1
Did you perform the Diagnostic System Check - Vehicle?
YES - Go to Step 2
NO - Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2
Turn ON the ignition, with the engine OFF.
Move the wiper switch to the LO position.
Move the wiper switch to the OFF position.
Do the front wipers advance to the park position?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Turn the ignition switch to the RUN position.
Turn the wiper switch to OFF.
Disconnect the wiper/washer switch connector.
Do the wipers park?
YES - Go to Step 7
NO - Go to Step 4
4
At the wiper/washer switch connector, measure the voltage of the windshield wiper switch signal 2 circuit.
Does the voltage measure greater than 1.0 volts?
YES - Go to Step 5
NO - Go to Step 8
5
Reconnect the wiper/washer switch connector.
Disconnect the wiper motor connector.
Measure the voltage of the windshield wiper switch signal 2 circuit.
Does the voltage measure greater than 1.0 volts?
YES - Go to Step 6
NO - Go to Step 8
6
Repair a short to battery positive voltage in the windshield wiper switch signal 2 circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
YES - Did you find and correct the condition?
NO - Go to Step 9
--
7
Replace the wiper/washer switch. Refer to Turn Signal Multifunction Switch Replacement in Steering Wheel and Column - Tilt.
YES - Did you complete the replacement?
NO - Go to Step 9
--
8
Replace the wiper motor cover. Refer to Wiper Motor Cover Replacement .
YES - Did you complete the replacement?
NO - Go to Step 9
--
9
Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 2

probably a fuse or wiring trouble

We do not have this model in the USA so have no tech support for it. Sorry

first check all panel and underhood fuses and if all o.k you need a multifunction switch which operates all of mentioned componants.