<!-- from fixya rte -->Exploded view of ignition system - Hyundai Motor 1996 Elantra

Fig. 3: Exploded view of the EGR system and related components for the 3.0L engine





Fig. 4: Exploded view of the EGR system and related components for the 4.0L engine

Hope helps (remember rated and comment this).

For 1996 Mazda MX-6 2.5L MFI DOHC 6cyl the Fuel Filter is located under hood, driver side, engine side of strut tower, below air filter housing, mounted in fuel line.



Fig. 1: Exploded view of a typical 4-cylinder engine fuel system




Fig. 2: Exploded view of a typical 6-cylinder engine fuel system

Hope helps with this; remember rated this.

You didn't post your engine size so please choose the appropriate one:



Exploded view of the ignition coils and related system components-2.2L engine shown.......2 coil packs




The ignition coils are secured to the module with retaining bolts/screws-3.4L engine shown......3 coil packs

Fig. Exploded view of the fuel system-1.5L and 1.6L (VIN 5) engine






Fig. Exploded view of the fuel system-1.8L engine





Fig. Fuel filter location-2.4L engine







Hope this help (remember comment and rated this).

The ignition module is integrated within the ignition coil itself, and the only repair possible is to replace the entire coil assembly. There are six ignition coils, therefore there are six ignition modules.

Fig.: Exploded view of the 2.0L engine coil pack assembly




Fig. : Exploded view of the 2.5L engine coil pack assembly



Hope this help (remember comment and rated this).

WARNING Never remove the radiator cap when the engine is hot. Serious burns could occur from high pressure coolant escaping from the radiator.
To remove and install thermostat, refer to illustration and water pump procedure.




Fig. Exploded view of water pump and thermostat components-1.6L engine



Fig. Exploded view of thermostat and components-1.8L engine




Fig. Exploded view of thermostat and components-2.0L engine


Removal & Install

1. Before servicing the vehicle, refer to the Precautions Section.
2. Drain the cooling system.
3. Disconnect the negative battery cable.
4. Remove the lower radiator hose.
5. Remove the water inlet and take out the thermostat.
6. To install perform the following:
   Install gum ring to thermostat Install thermostat with jiggle valve or air bleeder at upper side
   
7. To complete installation, reverse remaining removal procedure.
8. Fill the cooling system.
9. After installation, run engine for a few minutes and check for leaks.

Hope helped with this (remember rated this) Good luck.

1993 Ford Aerostar 4WD 4.0L MFI 6 Cyl Repair Guide

1. Drain the cooling system with the engine cold.
CAUTION When draining coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.

2. Remove the retaining bolts for the thermostat housing. Lift the housing clear and remove the thermostat. It may be easier to clean the gasket mating surfaces with the heater and radiator hoses removed from the thermostat housing.


Exploded view of the thermostat housing on the 2.3L engine




Exploded view of the water outlet housing and thermostat-make sure that the thermostat is correctly positioned as shown




Exploded view of the thermostat housing and thermostat-3.0L engine




Exploded view of the water outlet housing and thermostat-4.0L engines




I hope help you whit this (rated this help) Good luck.

dealer has better picture they can print out for you give them a call

Haynes.co.uk have great workshop manuals with exploded views of almost everything.