Question about 2007 Ford Edge SEL Plus

1 Answer

HOW DO YOU TEST THE PARK ASSIST ON A 2007 FORD EDGE

Check park assist light on , it stopped beeping .how do i check bumper sensors &control modual

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

Check with a diagnostic scan tool for module fault codes and sensor fault codes. If nothing comes back complete electrical circuit prove out.

Posted on Feb 03, 2015

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
michigan man

edgar walker

  • 3533 Answers

SOURCE: 2007 ford edge, three lights are on: ABS, wrench

it sound like a ABS-sensor is sticking are its bad give these websites a try www.alldatadiy.com and www.autozone.com if all fails stop by your local library and get your hands on a Haynes auto repair manual for your car wish you the best of luck Michigan Man.

Posted on Jan 12, 2010

Dantek1

  • 92 Answers

SOURCE: I have a 2006 Ford Explorer and 2 of my park aid

You only need to remove the bumper cover. Remove both tail lamp assemblies. Under the tail lamps you will a 10mm and a 8mm bolt, remove these. Look into each rear wheel well rearward and you will find a T20 torx screw on both sides, remove these. On the top of the rear bumper, between the bumper and the bottom of the liftgate opening you will find 6 to 8 plastic rivets that can be removed by pulling the center pins out, remove these. At this point you should be able to lift upward and rearward and release the bumper cover. Once the cover is free you must disconnect the electrical connector to the sensor wiring harness. With the bumper cover on the ground or a bench, you will see 4 9/16" nuts that hold the styrofoam bumper cushion to the bumper cover, remove these. Now you should be at the point where the backup sensors are accessable. When you install the new sensors be sure your electrical connectors click when they connect. these connectors go on hard and if they don't click you will be doing this job again. Reassemble in reverse order.
Hope this helps

Posted on Apr 03, 2010

Patsy Harris

  • 10 Answers

SOURCE: tire sensor fault light always on- Ford Explorer

check to see if one of (or more) the rims is bent,go to a tire place they will check it for cheap,if there is a bent rim they might be able to bang it out,or you might have to buy a new rim! have you driven over any potholes lately? or hit a curb?

Posted on Dec 14, 2010

Anonymous

SOURCE: THROTTLE POSITION SENSOR ON A 2007 FORD EDGE

Doubt it failed----did you test it with a volt meter,put
an oscilloscope on it,or look at scan tool data


Have a couple T20 Torx Screws that hold it on

You heat them with a hair dryer to soften the
Blue Thread Locker

Why not tell us the vehicles problems & what you tested so far

Posted on Aug 31, 2012

steve h woody

  • 2551 Answers

SOURCE: how ca I test the ignition coils in my ford edge 2007, v6, 3.5

you can buy a spark tester at most auto parts stores , while running check one at a time .

Posted on Sep 12, 2012

Testimonial: "thanks"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 Buick rendezvous rear park assist doesn’t work . No sound at sensor when checking in reverse .


See the awd fuse in under hood fuse box, not only check the fuse, use a test light and check voltage on fuse circuit, key on. There shows to be four park assist sensors at the rear bumper, they have three wire connector, that is ref voltage--ground--signal. You also have a rear park assist module, At the moment, I don't know where that is located? Any applicable trouble codes relating to rear park assist? I have some text explaining the operation, but, not really any troubleshooting sequence.
rpa-5y1fljthaqxrxj00dqnspoy2-2-0.jpg

Mar 27, 2018 | 2007 Buick Rendezvous

3 Answers

Service park assist system


where is the parking assist sensor??

Jan 21, 2013 | 2006 Jeep Grand Cherokee

4 Answers

The park assist service light comes on when i start the vehicle. i do not have an owners manual to reference.


{: ) The driver information center (DIC) displays SERVICE PARK ASSIST when the object alarm module detects a malfunction in the parking assist system and the system is disabled. The DIC also displays SERVICE PARK ASSIST when a loss of communication occurs with the object alarm module. Usually this is caused by faulty components or wirings. Better visit your dealer if still under warranty, for one park assist sensor only costs too much. If your bumper had been knocked off or had previous repairs outside the dealership, that's another thing.
The PARK ASSIST OFF message is displayed in the DIC when the parking assist system is disabled due to conditions that disable or inhibit the system. The object alarm module requests the DIC display PARK ASSIST OFF when it detects one of the following conditions:
• The parking assist system is manually disabled using the driver information center (DIC). • An object is attached to the rear of the vehicle, such as a trailer, bicycle rack, trailer hitch receiver, or tow bar. • The object alarm sensors are covered by snow, mud, dirt, slush, or ice. • The vehicle bumper is damaged, • Excessive paint thickness on a replacement object alarm sensor. • The object alarm sensors are disrupted by vibrations, like those caused by a large nearby vehicle or from heavy equipment such as a jackhammer.

Apr 14, 2011 | 2009 GMC Yukon

2 Answers

My 2007 Yukon has a problem with the park assist sensors. When I go in reverse sometimes, the warning beep repeats quickly and the lights flash like crazy but nothing is behind the vehicle. Sometimes the...


Check the system for DTC'S - diagnostic trouble codes should be the first step in the diagnostic process . Then reading factory service repair manual how the system works , viewing wiring diagrams .
Object Detection Description and Operation
Ultrasonic Rear Park Assist Operation
The ultrasonic rear park assist system senses how close the vehicle is to an object. The distance is determined by the 4 object sensors located in the rear bumper. The object detection system will notify the driver when backing up at speeds less than 8 km/h (5 mph). The object detection system will use the rear parking assist (RPA) display and the radio speakers for notification.
When the ignition is ON and the vehicle is placed into reverse, the object detection system performs a bulb check. During the bulb check, the 3 indicators on the RPA will illuminate for approximately 2 seconds to indicate that the system is working. The object detection system performs a bulb check and operates when the following conditions are present:
• The ignition is ON.
• The vehicle is placed in REVERSE (R) for rear parking aid.
• The vehicle speed is less than 8 km/h (5 mph). At speeds greater than 8 km/h (5 mph), the object detection system is disabled. The red indicator flashes to warn the driver that the object detection system is disabled.
The object detection system senses how close the vehicle is to an object. The distance is determined by the 4 object sensors located on the rear bumper. When the system detects an object, one of the following will occur:
• If the object is less than 0.3 m (11 in) away from the vehicle, the amber outside, amber middle, and the red outside indicators flash and the chime sounds continuously for 3 seconds.
• If the object is less than 0.3-0.5 m (11-20 in) away from the vehicle, the amber outside, amber middle, and the red outside indicators are ON.
• If the object is 0.5-1.0 m (20-40 in) away from the vehicle, the amber outside, and the amber middle indicators are ON.
• If the object is 1-2.3 m (40-91 in) away from the vehicle, the amber outside indicator is ON with a single chime when the object is first detected.
Object detection system can detect objects 7.6 cm (3 in) wide and at least 25.4 cm (10 in) tall. It cannot detect objects above the level of the roof.
If the object detection system detects a malfunction, a diagnostic trouble code (DTC) will be stored and the object detection system will send a serial data communication message to the instrument panel (I/P) to SERVICE PARK ASSIST message on the driver information center (DIC). Then the chime will sound and the red indicator on the information telltale center will be lit continuously. The red LED in the rear display will be lit, notifying the driver that a malfunction exists. Message will clear once the driver acknowledges it.
Each object sensor is a three wire sensor that is both a transmitter and a receiver that comprises a signal circuit, a low reference circuit, and an 8-volt supply voltage circuit. The rear object control module supplies 8 volts to the object sensors via the object sensor supply voltage circuit and provides ground via the low reference circuit. The rear object control module triggers the sensors in a sequential loop and after each sensor transmits, the rear object control module uses the echo or signal return to calculate the distance and position of an object from the rear bumper. The rear object control module directly controls the RPA display.

Do you know what DTC'S are ?
DTC B0958 01: Parking Aid Rear Sensor 1 Left Corner Circuit Short to Battery
DTC B0958 06: Parking Aid Rear Sensor 1 Left Corner Circuit Short to Ground or Open
DTC B0958 08: Parking Aid Rear Sensor 1 Left Corner Circuit Signal Invalid
DTC B0958 21: Parking Aid Rear Sensor 1 Left Corner Circuit Incorrect Period
DTC B0959 01: Parking Aid Rear Sensor 1 Left Middle Circuit Short to Battery
DTC B0959 06: Parking Aid Rear Sensor 1 Left Middle Circuit Short to Ground or Open
DTC B0959 08: Parking Aid Rear Sensor 1 Left Middle Circuit Signal Invalid
DTC B0959 21: Parking Aid Rear Sensor 1 Left Middle Circuit Incorrect Period

DTC B0967 02: Parking Aid Switch Circuit Short to Ground
DTC B0968 00: Parking Aid Indicator Circuit


Your best bet , take it to a qualified repair shop.

Feb 04, 2018 | GMC Yukon Cars & Trucks

1 Answer

Accoustic park assist makes long beep rather than beep beep


the long beep is to tell you its on.try asking someone to walk past when your in reverse about 18 inches from the bumper if it dont beep beep then try cleaning sensors.if that dont work then a sensor could be faulty..

Mar 10, 2010 | 2002 Audi A6

1 Answer

Park Assist Doesn't work On 2007 Solara


first try backing up close(6ins) to a wall then put car in reverse(sensors are powered by reverse lights circuit)see if it makes a noise when you press on/off button.if no then make sure you have reverse bulbs working,then check fuses.

Mar 08, 2010 | 2007 Toyota Solara

1 Answer

Why has the parking sensors on my bmw stopped working


There is few options.First-reverse switch not working.How to check-switch ign. ON,select Reverse and check reverse lights at back.If not-change switch.If O.K. go to step two: Disconect reverse sensors next to a bumper and check for resistance/any one/,because all sensors are conected in serie.If there is not resistance check all sensors one by one to find a wrong one.And last one-check "beep" speaker

Dec 07, 2009 | 2005 BMW 1 Series

1 Answer

2005 Lincoln Navigator. Message says to Check


Most likely the problem you are experiencing with the park assist is a fault in one of the sensors mounted in the rear bumper. I would not consider it to be a major fix, however there will be a few hours labor involved as the bumper cover needs to be removed to replace the sensors.

Jul 07, 2009 | 2003 Lincoln Navigator

Not finding what you are looking for?
2007 Ford Edge SEL Plus Logo

698 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...