2010 Dodge Nitro Logo
A
Anonymous Posted on Feb 17, 2015

How do i fix a stuck blend door on 2010 dodge nitro?

Very minimal heat, the air blows but very little heat comes out

1 Answer

Thomas Perkins

Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

  • Dodge Master 15,088 Answers
  • Posted on Feb 17, 2015
Thomas Perkins
Dodge Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Joined: Feb 12, 2010
Answers
15088
Questions
0
Helped
3386416
Points
54869

I would pull off the blend door actuator and swap it out with a new one. Or another option is to swap it out with one of the other actuators. The blend door actuator is interchangeable with the actuators for the mode-air doors and the recirculation-air door.

Disconnect and isolate the negative battery cable.

If equipped, remove the silencer from below the driver side of the instrument panel.

Disconnect the wire harness connector from the blend door actuator located on the driver side of the air distribution housing.

Remove the two screws that secure the blend door actuator to the actuator mounting bracket and remove the actuator

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

2009 dodge nitro blows heat on low setting only

topic cars and HVAC heat lost.
the heater blower resistor is bad.
or controls to it bad.
the vent problem is bad vent actuators or controls to them.
see hvac here

https://eautorepair.net/Marketing/Default.asp
0helpful
1answer

My heater blow out cold air

I would guess the blend door motor. You HVAC system can be scanned for codes.
0helpful
2answers

2010 dodge journey blows cold air on passenger side

Help with heating issues, blend actuator - Interior - Dodge ...

www.dodgejourneyforum.com/.../5304-help-with-heating-issues-blend-a...
Jan 13, 2014 - My 2009 Journey R/T is only blowing hot air out the driver side vents, while the other vents (passenger and rear) are blowing cold air ... Thanks Frogbox....keep in mind that the info is for the 2009 model and I guess it also applies to2010's. 2009 journy sxt heat/cool issue
Oct 16, 2014
Air Conditioning?
Dec 22, 2012
Rear heater A/C
Dec 22, 2012
More results from www.dodgejourneyforum.com

In a 2010 dodge journey why heat comes out just one side


1helpful
1answer

08 dodge nitro blows hot air on passenger side but cold air out the drivers side!! Any answers



NOTE: LHD model shown. RHD model similar. All vehicles are equipped with a common heater, ventilation and air conditioning (HVAC) housing assembly (1). The heating-A/C system combines A/C, heating, and ventilating capabilities in a single HVAC housing mounted within the passenger compartment behind the instrument panel. The HVAC housing assembly includes:
  1. Mode-air doors (2)
  2. A/C evaporator (3)
  3. Recirculation door actuator (4)
  4. Air inlet housing (5)
  5. Recirculation-air door (6)
  6. Blower motor (7)
  7. Blower motor resistor (8)
  8. Heater core (9)
  9. Air distribution housing (10)
  10. Blend-air door (11)
  11. Blend door actuator (12
  12. Floor distribution ducts (13)
  13. Mode door actuator (14)
0helpful
1answer

Hearter temp control was blowing too hot, now only blows cold

Clicking sound you hear is the worn brushes in your blower motor. At this point the blower moter may or may not start with the switch. THe blower motor is faulty so I would change that first, then check for vacuum leaks or faulty selector cable for the heat blend door. It could have came off door side or heater control side.
0helpful
1answer

Heating problems

Check for air in the cooling system - tighten carefully all hoses especially ones by expansion tank. If motor on cool down sucks in air instead of water an air bubble could restrict the flow of coolant into the heater core.
0helpful
1answer

2010 nitro dodge front vent not blowing air

Blend air door inop, either from vacuum leak, bad check valve or bad actuator.
Not finding what you are looking for?

3,338 views

Ask a Question

Usually answered in minutes!

Top Dodge Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...