My remote entry fobs will not program on my 2002 RSX.When I get to the stage where the locks are supposed to make noise, only the hatch lock does; the door locks are silent.The door switches are fine.

Looking at the service info for your Uplander, it has Remote Control Door Lock Receiver technology, so keyless entry should work if you have a capable key fob.

Your Uplander will need the key fob programmed by a service center or dealer with the technology to program those GM vehicles that can't be done manually (i.e. Tech 2 scan tool).

Check fuse and/or relay to see if blown/non-functioning. Should be labeled door lock or dr lock.

yes it needs the fob, Keyless Entry Remote Fob Clicker for 2002 Mazda Protege5 With Do It...



2002 Mazda Protg Keyless Remote Key Fob
http://www.fobkeyless.com/2002-mazda-protege-keys-remotes-replacement.html

One of the service writer guys at my local Acura dealer came out and programmed my new key fob on my RSX for me for free. Try that at your Mazda dealership. As I recall, I had to have all of the key fobs I planned to use on that car with me at the same time so that they would all get programmed the same. So bring all of yours with you, just in case.

Question edited for clarity.

The remote start is tied to the Lift Hatch. Your vehicle was likely not locked, so when you double clicked the lift hatch, it did what it is supposed to do and opened the hatch. If that is not the case, take it to a remote / alarm installer to check the programming.

How To Remote Start A Cadillac Escalade? - VEHQ

https://vehq.com > how-to-remote-start-cadillac-escalade
Jan 5, 2022 - 1. Press the lock button on the key fob to secure the vehicle. 2. Press the liftgate button on the key fob twice. Take note that not ...

..

The receiver for the fobs is located in the rear hatch, and it needs to be reprogrammed to the fobs. Try the following procedure;

1. Close all the vehicle doors.
2. Insert the ignition key into the ignition lock cylinder.
3. Press and hold the door unlock switch.
4. While holding the door lock switch in the unlock position, cycle
the ignition ON, OFF, ON, OFF.
5. Release the door unlock switch. The doors will lock and unlock to
confirm the program mode.
6. Press and hold the LOCK button and the UNLOCK button
simultaneously on one transmitter. After a delay of approximately 15
seconds, the doors will lock and unlock to confirm the programming of
that transmitter.
7. Repeat the previous step to program up to four transmitters.
8. Turn the ignition switch to the RUN position in order to exit the
keyless entry transmitter mode.
9. Operate the transmitter functions in order to verify correct
system operation.

try this...

1. Make sure vehicle is in Park
2. Press Vehicle Information button (has the icon of a car and an 'i')until 'PRESS *check mark* TO RELEARN REMOTE KEY' displays.
3. Press set/reset button. The message 'REMOTE KEY LEARNING ACTIVE' will display.
4. Press and hold the lock and unlock buttons on the transmitter at the same time for about 15 seconds. A beep will sound indicating that the transmitter is matched.
5. To match additional transmitters at this time, repeat Step 3. Each vehicle can have a maximum of four transmitters matched to it.
6. To exit the program mode, you must cycle the key to LOCK.

If that doesnt work, go to: http://www.bing.com/search?q=how+to+program+a+keyless+entry+fob+for+a+2002+Suzuki+Grand+Vitara&go=&form=QBLH&qs=n&sk=

first open it and check 1.5V bettery, and replace.

Open the remotes up...Are the boards the same...?

This is what i found but you need one fob.

here is another way if you can get it done( i bevlieve) There is a box under the dash of your can it says keyless entry if you have the right box and the fab just plug and play.

Make sure you get the screws in the defrost vent there is some screws and then it there is snaps


http://shopping.msn.com/specs/keyless-entry-remote-fob-clicker-for-2004-dodge-neon-with-do-it-yourself-programming-requires-1-wor/itemid1124228415/?itemtext=itemname:keyless-entry-remote-fob-clicker-for-2004-dodge-neon-with-do-it-yourself-programming-requires-1-wor