1999 GMC Jimmy Logo
A
Anonymous Posted on Feb 28, 2015

What process u have to use to reset drive cycle for 99 gmc jimmy evoy

1 Answer

Donald Chesley

Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Corporal:

An expert that hasĀ over 10 points.

Problem Solver:

An expert who has answered 5 questions.

  • Contributor 9 Answers
  • Posted on Mar 01, 2015
Donald Chesley
Contributor
Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Corporal:

An expert that hasĀ over 10 points.

Problem Solver:

An expert who has answered 5 questions.

Joined: Dec 12, 2014
Answers
9
Questions
0
Helped
1010
Points
33

General Motors Driving Cycle just make sure you have no codes and your chk eng light is not on,drove me nuts for weeks nothing would set so i got my own scanner and seen that the coolant was only reaching 140F so i changed the thermostat and the next ride everything set so look for the little things that might be wrong. http://www.obdii.com/drivecycle.html

5 Related Answers

alicantecoli

Colin Stickland

  • 22516 Answers
  • Posted on Nov 05, 2008

SOURCE: What is the cause of High emissions of Nitrous Oxide on 99 GMC Jimmy

new catalytic converter and oxygen sensors

Ad

Anonymous

  • 2 Answers
  • Posted on Mar 04, 2009

SOURCE: remove airbag 99 gmc jimmy

I actually just took mine out today on a 1998 Gmc Jimmy. Its kind of simple now that ive done it. There are four ten millimeter bolts holding the passenger module in. you will need to drop your glovebox down so it is upside down to see these. It is easier if you take it right off. just take a shop light and look at the bottom of the module you will see two silver bolts (the only two ten mm down there) take them out. Then if you look up underneath you will see another up at the top left. To get this out you can hand wrench it or you can use a mini impact with an ajustable extension. to get the next the easiest way I found was to take off the trim aroung your speedometer get in the drivers seat and there is another ten millimeter nut on the top right (right by the vent holes) take that out then you are unbolted. Without going into tons of details when you start doing it you will quickly realsie how to do it it just takes some patience. Dont forget to pull the fuse before you do anything its a 15 amp fuse second row 3rd up in the panel inside the car. Hope this helps

bharj

  • 88 Answers
  • Posted on Sep 16, 2009

SOURCE: where is the fuel reset button on a 92 gmc jimmy

there is no reset botton for fuel in this vehicle .

john h

  • 29494 Answers
  • Posted on Dec 02, 2009

SOURCE: I have a 99 GMC Jimmy with the 4 wheel drive. I

check fuse and relay to switch if power to switch retest switch new doesnt mean not defective if no power check connections and wiring for damage or breaks

swolfinor

STEVE WOLFINBARGER

  • 504 Answers
  • Posted on May 26, 2010

SOURCE: Programming garage door opener in a 99 gmc Jimmy

GOTO HOMELINK.COM

THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.

PLEASE NOTE: NOT ALL BRANDS/MODELS OF OPENER WILL WORK WITH THIS SYSTEM.

HOPE THIS HELPS

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

P1633 gmc code I've a GMC Evoy with that code what that code mean

GMC Evoy , what year is the vehicle ? an what engine ?
0helpful
1answer

How to fix the u joint on 99 GMC jimmy

REAR WHEEL DRIVE ? U-JOINTS @ DRIVE-SHAFT ? ITS VERY EASY EVEN A CAVEMAN CAN DO IT ! DON'T YOU HAVE A BOYFRIEND TO DO IT ? GET A HAYNES REPAIR MANUAL
0helpful
2answers

I replaced blower resistor on my 99 gmc jimmy its still blowing on the same speed as it was. could it be the relay?

Could be the switch.
Can you check for voltage on the terminals for the resistor ?
1helpful
1answer

Had to jump start, when tried to get emission insp I was told it would have to go through drive cycle to pass what is this

Cars do have a drive cycle to clear up a fault. It more less ensures the issue has been corrected after a certain drive cycle. Some issues have to cycled for 500 miles.
0helpful
1answer
1helpful
1answer

I have a 99 GMC Jimmy with the 4 wheel drive. I

check fuse and relay to switch if power to switch retest switch new doesnt mean not defective if no power check connections and wiring for damage or breaks
1helpful
1answer

My '99 gmc jimmy has a clicking noise inside the engine. the oil is full and it started after taking a long trip.....400 miles

Your valves need to be re-shimed  If your motor is the 2.2 the problem is quite normal.  Expensive to fix but normal.  You can sill drive the car fine. 
0helpful
1answer

97 JIMMY,PUSH 4X4 BUTTON,NOTHING HAPPENS

I had the same problem with my 99 Jimmy. try to disconnect your battery for about 5 minutes and see what happen. it fixed mine by doing it.
0helpful
1answer
Not finding what you are looking for?

109 views

Ask a Question

Usually answered in minutes!

Top GMC Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

john h

Level 3 Expert

29494 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...