Question about 2010 Volkswagen Caddy Maxi

1 Answer

Back door on vw maxi caddy 2010 wont open, all other doors working, any ideas

All other doors unlock and lock perfectly, only rarely will the back door open, when i press the button to open the back door i can hear lock engage/dis engage.

Posted by on

Ad

1 Answer

The motor may be moving, but the attached arm to the actuator could be broken, fell off, etc. You will need to open remove the door panel to see exactly whats going on.

Posted on Mar 03, 2015

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does anyone have a solution to fix my driver door locking mechanism? When I press the key fob to unlock the car doors. All the car doors unlock except for the driver door. However if you open the driver...


General advise:The lock is not ok.The same wires that lock the doors,unlock it.Before removing the lock:ceck fuses,door wiring link (near the door hinges)U may have to figure out the link covered in removabile rubber(it has a lock pin and must pull down in some cars rotate)U can clean it by air gun and contact cleaner.Rare:The door unlock pin (small plastic knob that u unlock manually from inside)has the rod dirty/stucked/twisted,ceck it to move loose.Also spray chain lube and wd40 anywhere in the lock u gain acces (the key hole,from sides,from the pin lock).U can see if it is stucked if the unlock knob has the intention to rise (small moves) but does not pop.Cheers.

Oct 24, 2013 | 2005 Renault Clio 1.5

1 Answer

My 2003 Lincoln Navigator front passenger door lock does not raise or lower using lock/unlock switch in car or on keyless entry. I hear a "grinding"sound when I try to open with the unlock...


That noise is due to a failed door lock actuator. This is the electrical device located behind the door panel that is responsible for popping the lock when you press the button. Door lock actuator replacement will eliminate the noise and bring it back to normal operation.

Mar 21, 2011 | Lincoln Navigator Cars & Trucks

1 Answer

97 Ford Explorer back doors won't open


A common problem with these are that the power door lock actuator freezes, and wont let the door unlock all the way,or the latch rusts up and again wont let door open, see if the lock arm is going up and down all the way, if not then try grabbing the lock with pliers and pulling up and then opening the door, or pull and push a few times then try to open the door, good luck.

Apr 08, 2010 | 1997 Ford Explorer AWD

2 Answers

Problem The rear hatch door will not unlock.


First, on the rear hatch, there is an actuator. On FX, when you close the trunk, it kind of **** the hatch closed all the way. When you press lock on the remote, this same actuator locks it as well.
Now,
1) when you unlock the car from the inside, go back there and press the button to open the hatch door manually, do you here any noises?
2) Close all doors, go back close to the hatch button and using the remote , lock the car and then unlock the car. you should hear a sound from the actuator locking and unlocking the lock on the rear hatch!

If you don't hear this, your actuator is inop.
Next step would be to check the fuses inside the car, on the left bottom driver side, and outside on the battery compartment.
It might be just a fuse.
If all fuses check ok, your actuator is most likely gone! Not ea expensive fix, just time consuming!

NOW, if you can hear the noises, then something is either broken inside the actuator or one of the cables is loose!
Hope that helps.
Also, what year and miles on your fx?

Oct 20, 2009 | 2004 Infiniti FX35

1 Answer

A friend of mine has a Lexus 1997 ES and his remote control needs reprogramming. How do I do it for him. Thank you so much.


1. Driver's doo opend and unlocked, all other doors closed and locked
2. Inser Your key in ignition, don not turn, remove key
3. using the manual lock/unlock button on ther dirvers door, slowly press lock and unlock 5 times (count the lock 5 times and unlock 5 times)
4. Shut door
5 Open door
6. Using the lock/unlock button on the direvers door, slowly press and unlock 5 times (count the lock 5 times and the unlock 5 times)
7. With the door open insert you key into the ignition, turn to ON position (don't start), wait 5 seconds. Trun off and remove key.
8. Locks should cycle once (Car will lock and unlock once). If they don't cycle or they cycle more that once, do stips 1-7 over.
9. Using the remote, push lock button, hold for 1 second, release. The locks should cycle once. If not start over and go slower.
10 Close the door. Open the door. Press the lock button on the remote. The locks should cycle. Close the door. Press the lock button on the remote, the doors should lock. Press again and the doors shoud unlock.

I got this from a site called FixYa (don't have URL). It took me a few tries but it worked like a charm.

Sep 24, 2009 | 1997 Lexus ES 300

1 Answer

Step by step reset the door remote control lexus 400LS


1. sitting in driver seat, with driver's door OPEN, press lock/unlock button ON THE DRIVERS DOOR to lock all doors, then manually unlock driver door only.
2. Insert YOUR key in ignition, DO NOT TURN, then remove key.
3. Using the same lock/unlock button ON THE DRIVERS DOOR, slowly press lock-unlock in 5 cycles
4. Shut door.
5. Open door.
6. Using the same lock/unlock button ON THE DRIVERS DOOR, again slowly press lock-unlock in 5 cycles
7. With the door open insert your key into the ignition, turn to 'on' position (DON'T START), wait 5 seconds. Turn off and remove key.
8. Locks should cycle once (Car will lock and then unlock once by herself). If they don't cycle or they cycle more than once, do steps 1-7 over.
9. Now using the remote, push lock button, hold for one second, then release the button. The locks should cycle once. If not, start over and go slower.
10. Close the door.
11. Open the door.
12. Press the lock button on the remote. The locks should do a lock-unlock cycle.
13. Close the door
14. Press the lock button on the remote, the doors should lock.
15. Press unlock button and the doors should unlock.

Jun 16, 2009 | 1996 Lexus LS 400

1 Answer

Un work of the doors auto control lexus


1. sitting in driver seat, with driver's door OPEN, press lock/unlock button ON THE DRIVERS DOOR to lock all doors, then manually unlock driver door only.
2. Insert YOUR key in ignition, DO NOT TURN, then remove key.
3. Using the same lock/unlock button ON THE DRIVERS DOOR, slowly press lock-unlock in 5 cycles
4. Shut door.
5. Open door.
6. Using the same lock/unlock button ON THE DRIVERS DOOR, again slowly press lock-unlock in 5 cycles
7. With the door open insert your key into the ignition, turn to 'on' position (DON'T START), wait 5 seconds. Turn off and remove key.
8. Locks should cycle once (Car will lock and then unlock once by herself). If they don't cycle or they cycle more than once, do steps 1-7 over.
9. Now using the remote, push lock button, hold for one second, then release the button. The locks should cycle once. If not, start over and go slower.
10. Close the door.
11. Open the door.
12. Press the lock button on the remote. The locks should do a lock-unlock cycle.
13. Close the door
14. Press the lock button on the remote, the doors should lock.
15. Press unlock button and the doors should unlock.

Long beep to follow if successful.

Jun 16, 2009 | 1996 Lexus LS 400

1 Answer

Need the steps to programme the remote


Remote Programming Instructions

1. Driver's door OPEN and unlocked, all other doors closed and locked.

2. Insert YOUR key in ignition, DO NOT TURN, remove key.

3. Using the MANUAL lock/unlock button ON THE DRIVERS DOOR, slowly press lock and unlock 5 times (count the lock 5 times and unlock 5 times).

4. Shut door.

5. Open door.

6. Using the lock/unlock button ON THE DRIVERS DOOR, slowly press lock and unlock 5 times (count the lock 5 times and unlock 5 times).

7. With the door open insert your key into the ignition, turn to on position (DON'T START), wait 5 seconds. Turn off and remove key.

8. Locks should cycle once (Car will lock and then unlock once). If they don't cycle or they cycle more than once, do steps 1-7 over.

9. Now using the remote, push lock button, hold for one second,
release. The locks should cycle once. If not, start over and go slower.

10. Close the door. Open the door. Press the lock button on the remote. The locks should cycle. Close the door. Press the lock button on the remote, the doors should lock. Press again and the doors should unlock.

Jun 02, 2009 | 1995 Lexus LS 400

3 Answers

Door lock 2004 jetta wagen


If remote locks and unlocks driver door but does not unlock passenger doors,then follow the advice above:
Get in the car using the key to unlock the doors. From the passenger side lock and unlock your doors using the button on the passenger door. Get out and the remote should now unlock all the doors with 2 presses.
Worked perfectly for me after several other suggestions (and dealer) failed.

Nov 07, 2008 | 2004 Volkswagen Jetta

Not finding what you are looking for?
2010 Volkswagen Caddy Maxi Logo

567 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...