Crankshaft torque settings e46 m43

Question edited for clarity, too many words :>D
Question moved to model category.

They are all in this link

https://www.hyundai-forums.com/threads/hyundai-getz-1-3-2005-g4ea-big-end-torque-settings.639857/

Hyundai Getz 2003 1 1 1 3 PDF

Scribd https://www.scribd.com > document > 138325436-HYU...
Tightening torque Main bearing cap bolt 1.3: 55 ~ 60 Nm (550 ~ 600 kg.om, 41 ... big end bear- ing. Crankshaft end play 1.3L: 0.05 ~ 0.175 mm (0.002 ~ 0.005 ...

..

Ideally you need a Workshop Manual. Help here

https://www.google.com/search?q=Ford+Bantam+1.6+Rocam.+Crankshaft+torque+settings

Service manual

https://www.google.com/search?q=Ford+Bantam+1.6+Rocam+service+manual

..

Suggest you buy a proper workshop manual. If you are doing main bearing replacements then you owe it to yourself, your wallet and your car to obtain a decent manual

You are looking for the torque settings for big end bearings and main bearings on a daewoo matiz?
Main bearings torques on a Daewoo Matiz 800cc (1999)
Stage 1: 25-30 Nm
Stage 2: 55-60 Nm
Big End Bearings…

https://www.google.com/search?q=Need+a+fuse+diagram+for+2012+Volkswagen+jetta+se+2.5&biw=1362&bih=650&tbm=isch&tbo=u&source=univ&sa=X&ved=0ahUKEwjz0O-MzZrQAhVC6CYKHYj2C54QsAQIIw&dpr=1#tbm=isch&q=what+are+the+torque+settings+for+Golf+5+GTI+2.0+for+crankshaft+main+bearings+and+big+ends%3B+mains+and+cylinder+head%3F
Hope this helps

Toyota Yaris Main and Big end Torques:
Tighten the main and big end bolts in sequential order and in steps two steps.
- Main bearings. Stage 1. 30 Nm.
Stage 2. 59 Nm.
- Big end bearings. Stage 1. 15 Nm.
Rotate further by 90 degrees.

Morning please advise on Torque settings for big end bearings on a ascent 1.3 X's please.

I have a 1997 Rodeo with the V6 3.2L engine. The crankshaft main bearing caps are torqued to 29(lb-ft).

The crankshaft pully is torqued to 123 (lb-ft).

Crankshaft torque settings for 2002 Audi TT 225 BHP:

1. Main bearings: Renew bolts = Yes
2. Main bearings: Stage 1 = 65 Nm
3. Main bearings: Stage 2 = 90 degrees
4. Big end bearings: Renew bolts / nuts = Yes
5. Big end bearings: Stage 1 = 30 Nm
6. Big end bearings: Stage 2 = 90 degrees
7. Flywheel / driveplate = 60 Nm + 90 degrees (use new bolts / nuts)
8. Crankshaft pulley / damper centre bolt = 90 Nm + 90 degrees (use new bolts)

Mains Stage 1 83nm
Mains Stage 2 167nm

Big ends Stage 1 29nm
Big ends Stage 2 45 - 60 degrees

Hope this helps