Location of coolant sensor - 2003 Chrysler Voyager

Question edited for clarity.
Question moved to model category.

Shown here

https://www.vwvortex.com/threads/coolant-temerature-sensor-location.9246449/

Videos

https://www.google.com/search?q=2017+Volkswagen+Tiguan.+Coolant+temperature+sensor+location

..

The Engine Coolant Temperature Sensor is located in the coolant pipe, below the air intake pipe and behind the right cylinder head and is integral with the ECT sensor. The Engine Coolant Temperature Sensor is located on the back of the right cylinder head and is integral with the ECT sensor.
https://www.autozone.com/repairguides/Audi-Cars-1999-05/Component-Locations/Engine-Coolant-Temperature-ECT-Sensor/_/P-0900c152801c0f85

This is for cc sport, 2.0L engine. #9 appears to be water/coolant pump. #7 shows to be coolant temp sensor. Hope this helps.

Not low input sensor...P0117 KIA - Engine Coolant Temperature Sensor 1 Circuit Low Input

Possible causes
Low engine coolant level
Faulty Engine Coolant Temperature (ECT) sensor
Faulty engine coolant thermostat
Engine Coolant Temperature (ECT) sensor harness is open or shorted
Engine Coolant Temperature (ECT) sensor circuit poor electrical connection

Just replace coolant temperature sending unit....

2002 Hyundai Santa Fe 2 7L coolant temp sensor location Google Search//2002 Hyundai Santa Fe 2 7L coolant temp sensor location Google Search Here are 2 locations with pictures. I found them thru Google in 2 minutes. You should be able to do something with them.

The coolant temperature sensor is a thermistor mounted in the engine coolant stream. A thermistor is an electrical device that varies its resistance in relation to changes in temperature.

For 2.5L engines, the coolant temperature sensor is located on the left side of the cylinder head.

For MFI engines, the coolant temperature sensor is located on the intake manifold water jacket or near (or on) the thermostat housing.



Fig. 1: Engine Coolant Temperature (ECT) sensor and connector




Fig.: Engine Coolant Temperature (ECT) sensor location-3.1L (VIN T) engine shown

Hope this helps (remember to rating this and leave an testimonial comment about this free answer).

On a V8 there are two sensors, the are located on either side of the neck where the thermostat is located. Standing in front of the vehicle the one on the left is for the temp. guage, the one on the right is for the computer.

If it is the six cylinder and you're getting the "COOLANT SENSOR BAD" message on the VIC that refers to the level sensor in the header tank. Is common in this models, I have one '93 ZJ and my signal Sensor Coolant Level also is ON for long time; first, try to clean the plug and reset the ECU. If the signal show again, maybe you need replace this sensor.

For more details about location and diagnotics, check this documents:
ZJ-Secc-8D-Ignition-Systems
- Page 5 Location (Coolant Temperature Sensor)
- Page 11 Diagnostics/Service Procedures
- Page 24 Removal Components

ZJ-Secc-7-Cooling-System
- Page 23 Coolant Reserve Tank (Coolant Sensor Level)

Hope this helps.

in the 5.2L V8 engine the coolant sensor is located on top of the engine. Locate the coolant thick hose coming from top of the ratiator to the top of the engine. Look at the place such hose connects to the engine you wont miss the sensor it is about one inch from there.

Hi!!

Thermostat location in 5 cil. engines, temp sensor is located just right or upper arrow in picture. I've included a picture of temp sensor and installation instruccions.



Never open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant. Also, when draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantities. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.

1. Drain the engine coolant.
2. Disconnect the ground cable of battery.
3. Remove the electrical connector from the sensor.
4. Remove the coolant temperature sensor.
   
   Fig. Coolant temperature sensor illustrated
   Coolant temperature sensor illustrated

To install:

1. Apply sealant to sensor threads. Install the sensor and tighten to 15-29 ft. lbs. (20-39 Nm).
2. Attach electrical connector to sensor.
3. Connect the ground cable of battery.
4. Refill the coolant.

If helpful, click below, good luck.