Question about 2008 Nissan Rogue

Open Question

I need step by step instructions on how to remove my rear bumper on my 2008 nissan rogue

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
abauto

Travis Mcilree

  • 353 Answers

SOURCE: need step by step instructions on how to remove a

Rear Bumper: Service and Repair
REAR BUMPER
Removal and Installation
REMOVAL
1. Remove the LH and RH rear combination lamps.
2. Remove both the rear wheels and tires.
3. Remove the LH and RH splash shields.
4. Remove the rear bumper fascia clips and screws, then remove the rear bumper fascia.
5. Remove the rear energy absorbing foam.
6. Remove the rear bumper reinforcement.
7. Remove the rear bumper supports.
INSTALLATION
Installation is in the reverse order of removal.

c674cde.jpg

Posted on Nov 12, 2009

Ad

lsrussell44

  • 1 Answer

SOURCE: "2008 nissan rogue problem shifting

It is the battery. It is bad and shorting out. Check the manual for directions to trouble shoot until you replace it. There is a small button that you need to remove next to the shifter, place the key in the hole and hold for about 10 seconds. It is a shift release.

I had the same problem. Fixed!

Posted on Apr 11, 2011

ginko

Ginko

  • 19396 Answers

SOURCE: Step by step instructions for

Hi.

Here you go:

1 - Remove one screw at each side's fender:

ginko_114.gif

2 Remove two screws and clips at the back.

ginko_115.gif
3 Pull out the bumper.

4 If needed remove screws holding spoiler support

ginko_116.gif
ginko_117.gif

5 Perform operations in reverse order to reassemble

Posted on Apr 16, 2011

Jonah Oneal

  • 14092 Answers

SOURCE: 2003 Chevrolet Impala LS.

RAISE REAR VECHICLE SUPPORT VECHICLE ON JACKSTANDS. MAKE SURE VECHICLE PARKED ON LEVEL SOLID GROUND.ONCE VECHICLE RAISED SAFELY SUPPORTED BY JACK STANDS. WORKING UNDER VECHICLE BUMPER DETACH THE FASTENERS SECURING THE BOTTOM OF THE BUMPER COVER. REMOVE THE SCREWS SECURING THE BUMPER COVER IN THE REAR WHEEL OPENINGS.OPEN TRUNK AND REMOVE THE SCREWS SECURING THE UPPER EDGE OF THE BUMPER COVER PULL THE BUMPER COVER OUT AND AWAY FROM THE VECHICLE.

Posted on Aug 12, 2011

Daniel Arellano

  • 136 Answers

SOURCE: how to remove 2008 toyota yaris rear bumper

Go to this site. http://www.yarisworld.com/forums/showthread.php?t=33767

Further down you will see a diagram of the bumper removal.

remove the two bolts under the hatch, the four plugs along the bottom edge, and the plate light. Don't forget the red circle clip or bolt on the diagram. Then you just pull it off.

Posted on Dec 01, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Removing tensioner assembly


images for 2008 Nissan Versa Removing tensioner

    how do you remove tension off surpentine belt tensioner - Nissan Forum

    www.nissanforums.com/.../151350-how-do-you-remove-tension-off.htm...

    Feb 20, 2009 - 4 posts - ‎2 authors
    2008+ Nissan Rogue ... QR25 2.5L Engine Engine Discussion: 2002+ Sentra SE-R and SpecV ... how do you remove tension off surpentine belt tensioner ... changed these before, but which way do you turn the tensioner, how ... Replacing the Water Pump on a '04-'08 Maxima *DIY*
    1 post
    Aug 31, 2011
    Belt noise: replace idler pulley? - GA16DE
    8 posts
    Sep 16, 2008
    Step by step instructions -Upper Timing Chain Tensioner
    15 posts
    Dec 8, 2007
    Idler Pulley Bearing Replacement Info
    5 posts
    May 16, 2003
    More results from www.nissanforums.com

    Nissan Versa Tensioner Pulley Issue (1/1) - EricTheCarGuy ...

    www.ericthecarguy.com/.../50669-nissan-versa-tensioner-pulley-issue
    Nissan Versa Tensioner Pulley Issue 1 year 7 months ago #94552 ... for a 50 Torx to be used to remove the entire tensioner pulley assembly but all of my 50Trx

    How to Replace serpentine belt 2008 Nissan Altima ...

    ? 11:29
    https://www.youtube.com/watch?v=5NchA85pnAE
    Jul 2, 2014 - Uploaded by nivekoch
    How to Replace serpentine belt 2008 Nissan Altima In this video i'll be going ... 2005 Nissan Altima 2.5L serpentine belt tensionerreplacement ...

Dec 16, 2015 | 2008 Nissan Versa

4 Answers

How do i find nissan rogue blower motor


It located in the passenger side of the car under the dash

Mar 05, 2015 | 2010 Nissan Rogue

1 Answer

Nissan pusal rear bumper removal instructions


DIY, you need a repair manual. Your autoparts store, or filepeep.com if they have it, or try manualslib.com

Nov 16, 2012 | 1990 Nissan Pulsar

1 Answer

Is ac resister removable without removing whole ac case


This is extensive steps to do this which you will need the actual diagrams from the manufacture. We can give them on our site as we pay them to allow us to distrubute them so there is no copyright issues come by and get the info plus help from a Mechanic

http://www.expertcaradvice.com/askquestion.php

Jan 22, 2012 | 2008 Nissan Rogue

1 Answer

"2008 nissan rogue problem shifting


It is the battery. It is bad and shorting out. Check the manual for directions to trouble shoot until you replace it. There is a small button that you need to remove next to the shifter, place the key in the hole and hold for about 10 seconds. It is a shift release.

I had the same problem. Fixed!

Nov 09, 2010 | 2008 Nissan Rogue

2 Answers

I don't remember the style of my 2008 Nissan Rogue (S, SL, SLUV). I need to buy new brake pads. Where do I find the model type?


2008 Nissan Rogue, is all you need.
Go to auto parts store.
I prefer raybestos ceramic,their dust free for the most part, and work well on my heavy Lincoln LS
Have the rotors turned.

Oct 19, 2010 | 2008 Nissan Rogue

2 Answers

I have a 2008 Nissan Rogue with the Intelligent Key keyless ignigition and entry system. Both of my keys appear to have dead batteries but I can't figure out how to open them to change the batttery


I also have a 2008 Nissan Rogue, and my intelligent keys quit working too. However, I do not believe it's the batteries, as one of my keys has never been used. I checked the fuses, but they are fine.

Oct 19, 2010 | 2008 Nissan Rogue

2 Answers

Need step by step instructions on how to remove a rear bumper cover on a 2007 nissan altima


Rear Bumper: Service and Repair
REAR BUMPER
Removal and Installation
REMOVAL
1. Remove the LH and RH rear combination lamps.
2. Remove both the rear wheels and tires.
3. Remove the LH and RH splash shields.
4. Remove the rear bumper fascia clips and screws, then remove the rear bumper fascia.
5. Remove the rear energy absorbing foam.
6. Remove the rear bumper reinforcement.
7. Remove the rear bumper supports.
INSTALLATION
Installation is in the reverse order of removal.

c674cde.jpg

Nov 12, 2009 | 2007 Nissan Altima 3.5 Sedan

1 Answer

How do you replace an in cabin micro filter on a 2008 nissan rogue


Remove instrument driver lower cover.
Remove accelerator pedal assembly.
Remove filter cover and then remove in-cabin microfilter.

Aug 26, 2009 | 2008 Nissan Rogue

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

510 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...