2009 Chevrolet HHR Logo
Sterling Hanley Posted on Mar 12, 2015

How do u find camshaft sensor on 09 Chevy HHR and replace ?

  • Anonymous Apr 04, 2016

    i know where they located i need to know are front and back the same

×

1 Answer

MARK GONZALEZ

Level 1:

An expert who has achieved level 1.

MVP:

An expert that got 5 achievements.

New Friend:

An expert that has 1 follower.

Hot-Shot:

An expert who has answered 20 questions.

  • Contributor 22 Answers
  • Posted on Mar 12, 2015
MARK GONZALEZ
Contributor
Level 1:

An expert who has achieved level 1.

MVP:

An expert that got 5 achievements.

New Friend:

An expert that has 1 follower.

Hot-Shot:

An expert who has answered 20 questions.

Joined: Nov 01, 2014
Answers
22
Questions
0
Helped
10380
Points
39

This, camshaft,, position sensor,, most of the time is located ,
behind the water pump,, and the timing belt.. but to make sure I recommend to buy the manual, repair book from your local auto parts for your vehicle when calling for the part sometimes the
auto parts store will tell you the location of the part you are
fixing to buy.
second step will be call the chevy dealer service dept.
and they can tell you, where this part goes..
I hope this help.... good luck...

5 Related Answers

delhooters

  • 5 Answers
  • Posted on Nov 22, 2008

SOURCE: air filter on chevy hhr

The air filter is in the large plastic cover that covers the engine.
1. Remove MAP sensor connector ( slightly hidden under the front center edge of the housing. Wiggle slightly and pull straight out).
2, Loosen (but don't remove) the large hose clamps on the passenger side and center of the housing, It's a tight fit for the hands on the passenger side and the head of the clamp is facing away from you. The front center hose is stiff, but pliable, so take your time.
3. The air filter housing was designed as a snap in with rubber grommets. A firm steady pull with the front passenger side will show you how much effort it will take to pull it free. Do each of the remaining two separately. The housing will be free to remove from the vehicle.
4. On a clear area, turn the housing over and loosen the seven torx type screws (they will not come completely off, so as not to lose them). Pull the cover off. Remove the old filter and replace with your new one. Align the cover and snug the screws back in.
5. Reassembly requires lining up those rubber grommets to the mounting studs.... take your time.... all that is needed is a firm downward push to seat them.
6. Reattach the large hose clamps and remember to plug in the MAP sensor (you'll get an "check engine" light if you forget.

Hope this helps.

Ad

Anonymous

  • 39 Answers
  • Posted on Feb 06, 2009

SOURCE: Where is the camshaft position sensor located-99 Chevy Lumina 3.1

It's held down by one bolt right above the timing chain cover. It's next to the head that's facing toward the front of the car.

Anonymous

  • 31 Answers
  • Posted on Nov 20, 2011

SOURCE: replace heater core on 2009 chevy hhr-how

get on youtube, and you will find the info that you need most of the time. you may need to remove the entire dash, to access this unit. so, be very sure what you are doing, before you tackle this job.

tayjoejoe

Joe Taylor

  • 2229 Answers
  • Posted on Feb 19, 2012

SOURCE: 2006 hhr chevy wont start

These cars have a tricky ANTITHEFT SECURITY system. When they recieve no voltage or low voltage, they consider this a threat and lock you from starting the vehicle. I'm sure it has probably reset by now, but here is a link to help if it happens again.

http://vatspasslockpasskeysecurityhelp.yolasite.com/

skychief2001

Stephen

  • 21873 Answers
  • Posted on Sep 04, 2012

SOURCE: Traction control on chevy hhr 2006

The traction control and transmission shifting would involve the body computer more so than the engine computer.
Have you had the body computer scanned for trouble codes ?

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Program remote fob 09 chevy hhr

The ONLY way to program a HHR remote is with a computer interface. Don't waste your time doing all of those dances, the Might apply to other GM products NOT to HHR.
0helpful
1answer

Help i need to know if camshaft position sensors on 2009 hhr 2.2 are both the same on front and back

No they are different, in basic terminology the front one is reading off the cam for the engine timing, while the rear one is reading for the fuel / air mixture, at least this is what the Chevy mechanic told me.
3helpful
3answers
0helpful
1answer

What does CarMD Code P0010 refer to on a '09 Chevy HHR LT with a 2.4L engine?

code p0010 refers to camshaft position (CMP) actuator , intake /left /front bank 1 circuit malfunction===causes --wiring---CMP actuator --ECM.
check that all the wiring connections are clean and tight--replace CMP actuator.
0helpful
1answer

Po340 and jerky motion 09 hhr

http://www.chevyhhr.net/forums/problems-service-repairs-42/reduced-engine-power-engine-shutdown-error-code-p0340-p0601-47411/page2/ Reduced engine power engine shutdown error code P0340 and P0601 Chevy...
0helpful
2answers

Camshaft sensor in 2009 hhr

You should probably take the car to a reliable shop or the dealer for that problem because those codes pertain to the intake and exhaust camshaft position actuator valves - not the sensor itself. It's more than just simply replacing the sensor for that problem.
2helpful
1answer

On a Chevy Hhr has p0014 code what needs repaired?

P0014 Camshaft position B over advance,or system performance bank 1.Clear the code,This appeared from either logic or rational.Camshaft postion usually appear on vehicle that are not in oil maintaince,this sensor has a tendency to get sluge built in it.This also appear when driver run the fuel very low,clear the code if it reappear its a hard code and a replacement or a service (clean it with gas or carb cleaner)it. is the solution
2helpful
1answer

2006 hhr 2.4 won't start after replacing both camshaft position sensors.

Did you remember to plug in the MAF sensor? Are you sure the air chamber is correctly installed on the throttle body?

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

0helpful
1answer

2006 hhr chevy wont start

These cars have a tricky ANTITHEFT SECURITY system. When they recieve no voltage or low voltage, they consider this a threat and lock you from starting the vehicle. I'm sure it has probably reset by now, but here is a link to help if it happens again.

http://vatspasslockpasskeysecurityhelp.yolasite.com/
Not finding what you are looking for?

719 views

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

john h

Level 3 Expert

29492 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...