I have broken the key in the ignition and lost the keyless entry remote. how do disconnect or bypass the immobilizer so i can start the car without the sentry key
Yes you need 2 keys to program a 3 key and you can us up to 8 keys
You can not disable this system. The powertrain control module (PCM) programmed look for the Transponder Key (your ignition key has micro chip code). You will have replace your ignition switch and get new key reflashed by a dealer or locksmith
SOURCE: remote keyless entry
“CUSTOMER LEARN” MODE
This feature is only available on domestic vehicles or those which have a U.S. country code designator. This procedure requires access to at least two valid Sentry Keys. If two valid Sentry Keys are not available, Sentry Key programming will require the use of a scan tool.
The steps required to program Sentry Keys with two valid Sentry Keys follows:
1.
Obtain the blank Sentry Key(s) that need to be programmed. Cut the keys to match the ignition lock cylinder mechanical key codes.
2.
Insert one of the two valid Sentry Keys into the ignition switch and turn the ignition switch to the ON position.
3.
After the ignition switch has been in the ON position for longer than three seconds, but no more than fifteen seconds, cycle the ignition switch back to the OFF position. Replace the first valid Sentry Key in the ignition lock cylinder with the second valid Sentry Key and turn the ignition switch back to the ON position. The second valid Sentry Key must be inserted within 15 seconds of removing the first valid Sentry key.
4.
About ten seconds after the completion of Step #3 , the indicator light will start to flash and a single audible chime tone will sound to indicate that the system has entered the "Customer Learn" programming mode.
5.
Within sixty seconds of entering the "Customer Learn" programming mode, turn the ignition switch to the OFF position, replace the valid Sentry Key with a blank Sentry Key transponder, and turn the ignition switch back to the ON position.
6.
About ten seconds after the completion of Step #5 , a single audible chime tone will sound and the indicator light will stop flashing and stay on solid for three seconds and then turn off to indicate that the blank Sentry Key has been successfully programmed. The SKREES will immediately exit the "Customer Learn" programming mode and the vehicle may be started using the newly programmed Sentry Key.
NOTE:
The Remote Keyless Entry (RKE) Transmitter will also be programmed during this procedure.
These steps must be completed in their entirety for each additional Sentry Key to be programmed. If any of the above steps are not completed in the given sequence, or within the allotted time, the SKREES will exit the "Customer Learn" programming mode and the programming will be unsuccessful. The SKREES will also automatically exit the "Customer Learn" programming mode if:
NOTE:
If you attempt to start the vehicle while in “Customer Learn” mode (LED flashing), the vehicle will behave as though an invalid key is being used (i.e. the engine will stall after two (2) seconds of running). No faults will be logged.
NOTE:
Once a Sentry Key has been programmed to a particular vehicle, it cannot be used on any other vehicle.
SOURCE: Hi my 2001 dodge caravan was stolen about 2 weeks
you have to take it to the dealer and get the anti theft module reflashed - most dealers charge around 95.00
SOURCE: How do i self program a keyless entry remote for my 2005 ram
ATTENTION: You MUST HAVE one working remote to add one more to the system. If you do not have one working remote right now then these instructions will not work. You will have to have a Locksmith or dealership use a computer to program the first remote for you.
1. Turn ignition to the RUN position (as far as you can go without starting the engine).
Wait for chimes to stop.
2. Using original programmed remote, press and hold the UNLOCK button on the
remote for between 5 and 10 seconds.
3. While holding UNLOCK button, and before 10 seconds passes, press and release
the PANIC button. A chime will sound to indicate that the transmitter programming
mode has been entered.
4. Within 30 seconds of the chime, press a button on all remotes to be programmed
into the system including any previously programmed remotes, a chime will
sound after each remote has been programmed.
5. Turn the ignition OFF to exit the transmitter programming mode.
6. Test Remotes
Thank you for using fixya and good luck
SOURCE: keys locked in 2002 durango
use a large screwdriver with a towel wrapped around it to prise the top of the door away from the frame,then use a wire coathanger to grab keys, you may need help to do both.then if the door is not fitting properly, wind the window down and bend the top inwards.
4,498 views
Usually answered in minutes!
×