Question about 2007 Hyundai Getz 1.4

Open Question

How do I replace the clutch and thrust bearing on getz 1.4 2007

Posted by on

Ad

2 Suggested Answers

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Bill Boyd

  • 53770 Answers

SOURCE: how to replace hyundai getz clutch

This ia a big jobunless you have mechanical knowledge. I suggest you get a manual and read up before you tackle this job. If you have no experience it would be cost effective to have this job done in a clutch and brake shop

Posted on Mar 18, 2013

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

VW Polo 2012 1.4 makes noise on gearbox but when clutch is pressed it gets silent. i have replaced clutch kit but noise still exist.


Sounds like the thrust bearing is worn. The thrust bearing is always replaced when repairing a clutch.

Sep 27, 2018 | Cars & Trucks

2 Answers

When i press the clutch pedal down it makes a rubbing noise similar to worn brake pads.stuart


opel vectra ,,,,ot sure if their is a automatic adjustment on the pedal ,if so it could be this failing which the cable could be frayed ,would really need to see it to know for sure

Feb 08, 2016 | Opel Vectra Cars & Trucks

1 Answer

Noise on gearbox when clutch pedal is pressed down


Hi,I know money is sometimes an issu,but realy when you replace the release bearing you should also replace the presure plate and the clutch plate at the same time so that thay all ware in at the same time,all the best.

Apr 28, 2015 | 2008 Opel Corsa 1.6

1 Answer

What causes that sound coming from the clutch side like that of a worn sprocket gear when you trail at low speed.


Hi,it could be that your thrust bearing is whereing out,its the bearing that when you put your foot on the clutch pedle it connects with the presure plate that lets the clutch plate have movement to spin,like aney bearing can where out,unless clutch is ferly new you should replace the free parts,
clutch-plate
pressure-plate
thrust-bearing(release-bearing)
but of coures only if it gets worse
hope this was some help.

Mar 29, 2015 | Cars & Trucks

1 Answer

Daughters 2002 Hyundai Getz is stuck in what i think is second gear.


Worn Clutch plate or thrust plate.

Check if hydraulic Clutch
if so check clutch fliud level . Could be a faulty clutch master cyclinder in hydraulic system.

Jan 15, 2015 | 2002 Hyundai Getz

1 Answer

Audi a3 1.9 tdi 2006 had the full clutch replaced has there was a loud metal on metal chaffing noise , was told it could be the thrust bearing on the clutch , still the problem is there after i have been...


You should take it back to where the clutch was done. They should have check the thrust bearing, flywheel and everything else associated with the clutch when they replaced it.

May 30, 2012 | Audi A3 Cars & Trucks

3 Answers

The clutch in my 1983 Chevy truck rattles when I push it in


the thrust (release) bearing is worn, not a big deal in itself as it will last a long time like this, but if the noise annoys you the bearing is very cheap, though to change it means removing or pulling back the gearbox so if the clutch is not new you could replace the whole lot as easily while in there

Jan 14, 2010 | 1983 Chevrolet Silverado

3 Answers

Clutch is noisy,when i depress the clutch the noise goes away


this noise is caused by a noisy clutch throw-out/release bearing, that is the part that presses against the pressure plate and disengages the clutch disk, the transmission must be removed to replace this part, so it is best to replace the clutch assembly at the same time, the labor for both is the same, about 5 hours

Oct 23, 2009 | 2003 Toyota MR2 Spyder

1 Answer

How easy is it to replace a noisy clutch thrust bearing. 53 plate Ford Focus 1.6 petrol zetec.


The thrust bearing is normally a part of a new clutch kit.Comprises pressure plate, clutch plate and thrust bearing.You will need to remove the gear box to change the bearing.The bearing basically slides onto the gearbox shaft. Recommend changing all three rather than just the beaing.You may want to get quotes from garages as dealers are expensive.

Mar 08, 2009 | 2003 Ford Focus

1 Answer

Slipping clutch


when you replace the clutch... always replace the thrust bearing as well.

Robert

Dec 17, 2008 | 2005 Porsche Carrera Gt

Not finding what you are looking for?
2007 Hyundai Getz 1.4 Logo

Related Topics:

196 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...