How do you remove the power steering pump from a 2007 Ford Edge

Here's a video on how to replace your belts.Good luck. 2008 ford edge belt replacement Applies to 2007 2014 models

remove fluid from power steering res and disconnect the return hose jack front of vehicle up high enough to get behind engine to firewall the powersteering unit is located there place jack stands under vehicle for safety then get under vehicle to remove hose from powersteering unit, observe routing of hose to replace new hose

CAUTION: While repairing the power steering system, care should be taken to prevent the entry of contaminants or premature failure of the power steering components may result.

1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02 .

1. Using a suitable suction device, siphon the power steering fluid from the power steering fluid reservoir.

1. Remove the RH inner fender splash shield. For additional information, refer to Section 501-02 .

1. Using the special tool, disengage the power steering pump belt from the power steering pump pulley and position it aside.
   • Install the removal tool between the belt and the pulley and turn the crankshaft bolt clockwise to disengage the belt.

1. Remove the 4 bolts and position the driveshaft aside.

1. Using a suitable jack, support the rear of the subframe.

1. Remove the 2 nuts, 4 bolts and the subframe support brackets.

1. Remove the 2 middle subframe nuts.

1. Lower the rear of the subframe.

1. Release the clamp and disconnect the power steering supply hose from the power steering pump.

1. Disconnect the power steering pressure (PSP) switch electrical connector.

1. Remove the power steering pressure line fitting banjo bolt and disconnect the line from the power steering pump.
   • Discard the 2 seals.

1. Remove the 3 power steering pump bolts and the power steering pump. This is a job best left to a qualified repair shop !

Power Steering Pump - 4.0L Special Tool(s) Installer Set, Teflon® Seal
211-D027 (D90P-3517-A) or equivalent Material Item Specification MERCON® V Automatic Transmission Fluid
XT-5-QM (or XT-5-QMC) (US); CXT-5-LM12 (Canada) MERCON® V
Item Part Number Description 1 388898 Teflon® seal 2 - Pressure line-to-pump fitting (part of 3A719) 3 W700839 Power steering pump bolts (3 required) 4 3A674 Power steering pump 5 W503924 Pressure line bracket-to-engine bolt 6 3691 Power steering pump supply hose 7 W503924 Power steering pump supply hose bracket bolt
Removal
NOTICE: While repairing the power steering system, care should be taken to prevent the entry of foreign material or failure of the power steering components may result.

1. Using a suitable suction device, remove the power steering fluid from the reservoir.

1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02.

1. Remove the power steering pump pulley. For additional information, refer to Power Steering Pump Pulley - 4.0Lin this section.

1. Remove the pressure line bracket-to-engine bolt.

1. Remove the power steering pump supply hose bracket bolt.

1. Release the power steering pump supply hose clamp and disconnect the hose.

1. Disconnect the pressure line-to-pump fitting.
   • Remove and discard the Teflon® seal.

1. Remove the 3 bolts and the power steering pump.

Installation

1. NOTE:A new Teflon® seal must be installed.Using the Teflon® Seal Installer Set, install a new Teflon® seal to the pressure line fitting.

1. Position the power steering pump and install the 3 bolts.
   • Tighten to 25 Nm (18 lb-ft).

1. Connect the pressure line-to-pump fitting.
   • Tighten to 75 Nm (55 lb-ft).

1. Connect the power steering pump supply hose.

1. Install the power steering pump supply hose bracket bolt.
   • Tighten to 11 Nm (97 lb-in).

1. Install the pressure line bracket-to-engine bolt.
   • Tighten to 11 Nm (97 lb-in).

1. Install the power steering pump pulley. For additional information, refer to Power Steering Pump Pulley - 4.0Lin this section.

1. Fill the power steering system. For additional information, refer to Section 211-00.

you will probably have to drop the tank but you could look for a trap door under the carpet.

before start job suction out power steering fluid out of pump using large sirenge or siphon pump then.you need a table vise and two pieces of wood.okay to remove power steering pump. you need to disconnect the ground cable.remove air intake duct.remove the pulley cover.remove the drive belt.disconnect power steering pump switch connector.disconnect the pressure hose and the suction hose from the power steering pump.cover power steering hose and pipe keep getting trash dirt and debris.remove the installation bolt of the power steering pump bracket.place the oil pump bracket in a vise btween two pieces of wood keep from damaging bracket and remove the two bolts from the front side of the pump.remove bolt from rear side of the oil pump.disassemble the oil pump and the bracket by inserting flat tip screw driver.to install tighten oil pump to bracket bolts 12 ft lbs. tighten the bolt from the rear side of the oil pump to 27 ft lbs.tighten steering hose eye bolts to 30 ft lbs.replace fluid bleed air out power steering system.

Check this video out,will send 2 of them. 2007 Ford Focus power steering pump Here's the other one. 2007 Ford Focus 2 0 Power Steering Replacement . "IMPORTANT: To improve longevity of system, manufacturer recommends installing in-line filter to catch excess contamination, part number 70702"

steering rack!

your local auto store should have one.