Anonymous Posted on Apr 13, 2015

When i changed ignition on 2001 ford explorer I ended up having to replace steering column now it wont turn over & the anti theft light flashes & wont stop. what can be done to get car started?

I have tried the following things already: 1.) radio, dash lights, and door locks all work, 2.)locksmith made new keys, 3.) charged the battery & 4.) throwing code "no tx verify"

roughnready_ Apr 13, 2015

Hi Anonymous, I want to help you with your question, but I need more information from you. Can you please add details in the comment box?

Did the locksmith make new transponder keys?

2 Answers

Mo Ty

Contributor 1 Answer
Posted on Jan 05, 2016

Mo Ty

Contributor

Joined: Sep 16, 2015

Answers

Questions

Helped

799

Points

What security code goes in the radio?

Steve F

Master 1,361 Answers
Posted on Apr 13, 2015

Steve F

Master

Joined: Jun 16, 2011

Answers

1361

Questions

Helped

567086

Points

3788

At least you know the anti theft system is working. Jokes aside, I would think that the electronic security system is not recognising the new lock and steering column. You could try leaving the battery completely disconnected for at least 2 or 3 hours to see if the system resets. Reconnect the battery and then try again with the new key. You will have to put the security code back into your radio as well. If this doesn't work, it may need to go to a Dealer to reprogram your electronic system.

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

0helpful

2answers

I had to replace the steering column on my 2010 Chevy Impala now it's stuck in anti theft mode. What can I do to get it back ?

This is how you do a security system reset on an Impala. I hope you have the transponder receiver connected on the new column.

https://www.vehiclehistory.com/questions/how-do-i-perform-a-chevy-impala-security-reset-93585

Chevy Impala Won't Start Security Light - It Still Runs

https://itstillruns.com > chevy-wont-start-security-light-...
Make sure the security light is flashing. After 10 minutes the security light will stop flashing and either turn off or stay on steadily. When it does, then ...

How to reset anti theft system on a 2008 chevy impala - Fixya

https://www.fixya.com > ... > 2008 Chevrolet Impala
Sep. 1, 2019 - Turn ON the ignition, with the engine OFF. · Attempt to start the engine, then release the key to ON (vehicle will not start). · Observe the SECURITY light, after ..

..

Read full answer

Sep 20, 2021 • Cars & Trucks

0helpful

1answer

2001 Ford explorer anti-theft system reset

check for worn --damaged key-- ignition cylinder --ignition switch

Read full answer

Sep 12, 2021 • 2001 Ford Explorer

0helpful

1answer

Changed steering column with another one , everything comes on but wont start.

Did you put the original anti-theft module on the new steering column ? Does yours have steering column mounted ignition switch ? Vehicles with steering column mounted ignition switches have the exciter integral with the theft deterrent control module (VTD) which is located within the steering column.

Read full answer

Aug 29, 2015 • 2004 Pontiac Montana

0helpful

1answer

How do I reset the anti theft device on my 1998 Ford Explorer? Changed entire steering column and ignition...

Now all you need to do is get it to the dealer to have it programmed. Sorry, Fords have to go to the dealer for security.

Read full answer

May 12, 2015 • 1998 Ford Explorer

0helpful

1answer

When i changed ignition on '01 ford explorer I had to replace steering column&it wont turn over&the theft light flashes&wont stop.The locksmith said antenna dont match Can i reprogram so it'll start?

The theft light flashes when the is off If it is flashing when the key is on I would think you don't have power in the correct position in the ignition.Check fuses and wiring.

Read full answer

Apr 22, 2015 • 2001 Ford Explorer Sport

0helpful

1answer

How do I reset the anti theft device On my 1998 Ford Exploeer?I had to change the entire steering column and know My car will not

How do you know anti-theft needs to be reset ,Is the security light on or flashing ? Maybe a wiring connector didn't get hooked up correctly .

Read full answer

Mar 01, 2015 • 1998 Ford Explorer

1helpful

1answer

Where Is the anti theft module

Passive Anti-Theft System (PATS) Transceiver module is around the key lock cylinder behind or under the plastic cover on the upper steering column'
Passive Anti-Theft System (PATS) Transceiver Removal

CAUTION: Electronic modules are sensitive to electrical charges. If exposed to these charges, damage may result.
Disconnect the battery ground cable, Refer to Section 414-01

Remove the ignition switch lock cylinder.
1. Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
1. Push the ignition switch lock cylinder release tab with a punch while pulling out the ignition switch lock cylinder.
2. If equipped, remove the tilt wheel handle.
3. Remove the upper and lower steering column shrouds.
  1. Remove the screws.
  1. Remove the upper and lower steering column shroud.
  2. Remove the lower instrument panel steering column cover.
    1. Remove the screws.
    1. Remove the lower instrument panel steering column cover.
    2. Remove the instrument panel steering column opening cover reinforcement.
      1. Remove the bolts.
      1. Remove the instrument panel steering column opening cover reinforcement.
      2. Remove the anti-theft transceiver module.
        
        Remove the screw from the bottom of the transceiver module.
        
        NOTE: Only apply pressure or leverage below the key cylinder lower rib.
        Disconnect the electrical connector and remove the module.

Read full answer

Dec 24, 2014 • 2006 Ford Taurus

0helpful

2answers

My 99 ford explorer won't start. When i turn the key, i get nothing. All my lights and electrical work. I suspect the anti-theft module under the steering wheel, because the "theft" light blinks when i...

you could pull the fuse disabling th anti theft totally.. not sure that would work though

Read full answer

Aug 09, 2010 • 1999 Ford Explorer

2helpful

2answers

2001 ford windstar won't start

my 2001 ford windstar wont start, i was driving it and completly lost power it would chug like it was running out of gas then had no power,shut it off and it wouldnt start again after that.I changed the mass air low censor,the fuel pump,the ignition switch,relays and fuses the brain box,i have no idea what to change next have any suggestion that could help that would be great thanks

Read full answer

May 27, 2009 • 2001 Ford Windstar

0helpful

1answer

R&R Steering Wheel Assembly and/or Steering Column Assembly

if you disconnect the battery and let it sit awhile this will disable the airbag.

Read full answer

May 15, 2009 • 1998 Ford Explorer

Not finding what you are looking for?

View Most Popular

2001 Explorer Sport

Cars & Trucks

I had to replace the steering column on my 2010 Chevy Impala now it's stuck in anti theft mode. What can I do to get it back ?

Cars & Trucks

809 views

Ask a Question

Usually answered in minutes!

Check Out the Latest Top Trucks Report!

View all Fixya Reports

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Have a manual for 2001 Ford Explorer Sport? Or just drag it here!

Related Topics:

When i changed ignition on 2001 ford explorer I ended up having to replace steering column now it wont turn over & the anti theft light flashes & wont stop. what can be done to get car started?