1997 Mitsubishi Mirage Logo
Dallas down Posted on Apr 29, 2015
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

How do I bleed my clutch on my Mitsubishi mirage 1997 model I'm on the side of the road

1 Answer

ka4iup

Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

  • Mitsubishi Master 4,062 Answers
  • Posted on Apr 29, 2015
ka4iup
Mitsubishi Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Joined: Mar 16, 2009
Answers
4062
Questions
0
Helped
1095799
Points
51404

Not really a side-of-the-road procedure:
http://www.dsmtuners.com/threads/how-to-properly-bleed-your-hydraulic-clutch.213503/

5 Related Answers

Danniboi

Dan Doherty

  • 1099 Answers
  • Posted on Feb 14, 2010

SOURCE: looking for a manual. 1997 Mitsubishi Mirage

Hi I found these, scroll down to the bottom of the page

Hope this helps, please click the link

Regards
Dan
http://shop.ebay.co.uk/?_from=R40&_trksid=p3984.m38.l1313&_nkw=1997+Mitsubishi+Mirage+manual&_sacat=See-All-Categories

Ad

Anonymous

  • 29 Answers
  • Posted on Dec 04, 2010

SOURCE: my clutch in my 95' mitsubishi mirage is sticking

could be the fluid. if the clutch was worn out it would be doing the opposite of sticking. is the clutch pedal easier to push than normally?

Anonymous

  • 153 Answers
  • Posted on Jan 04, 2011

SOURCE: HOW TO ADJUST HEADLIGHTS IN

There are torex screws on under the hood above headlights you can use a 6mm / 12 point socket or wrench also

Anonymous

  • 368 Answers
  • Posted on Jan 21, 2011

SOURCE: fuel gauge reading half with full tank on 1997

It is a fuel gauge sensor also known as the level sensor, There is a level sensor that has a boot spring attached to it that is probraly jammed, or just simply damaged. This will need to be replaced, you can located this at your fuel pump, which in normal case is underneath you rear seat in which side is your fuel door is located. Once you located the opening of the fuel pump passage then there is normally 6-8 small bolt that is screwed to hold your fuel pump to the fuel tank and some cable harness. Theses will need to be taken off in order for you to take your fuel pump. In my best advice, you minus well replace your whole fuel pump system to save time and complication when installing

Anonymous

  • 2 Answers
  • Posted on Nov 12, 2011

SOURCE: where is the fuel pump location on a 1997

The fuel pump is located in the fuel tank. You MUST drop the tank to see and replace it.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Firing order for 97 Mitsubishi, mirage

The firing order would depend on which specific model and engine you have in your mirage. A complete list with diagrams can be found here:

http://www.autozone.com/repairinfo/repairguide/repairGuideContent.jsp?pageId=0900c15280037cb8
0helpful
1answer

How to bleed my mirage clutch

please visit link below for mitsubishi forums
0helpful
1answer

Where is my fuel filter on my 95 mitsubishi mirage coupe

look under the car along the driver side, could be under a little cover follow the gas lines
0helpful
1answer

Becoming increasingly difficult to select all gears,as if clutch not fully dis-engaging although clutch is working properly

Check to make sure there is not air in the hydraulic system this will cause the slave cylinder to only partially operate thus causing difficulty in shifting gears also check the condition of the slave cylinder itself. Be sure its not leaking. Last but not least the synchronizer in the tranny may be bad cusing the problem.If there is are in the hydraulic system try bleeding the system.
0helpful
1answer

Clutch will not engage, when you force it , you can hear it spinning or whatever. when you turn off engine it shifts great. please advise how to adjust clutch petal, it is low or soft, EMERGENCY PLEASE

Replace your Clutch, Hydraulic Clutch System can't be Adjusted but check if oil level is good if not add the missing oil ( With DOT-3 Brake Oil ) try by bleeding it if nothing changed, your clutch need's to be Replaced !
0helpful
1answer
0helpful
1answer

Where i can find the vin number on the engine block of a mirage 1997 ,1.5

go to out side vechlcle on driver side look through windshield its the long number on dash.your vin number is also on vechicle registration.
Not finding what you are looking for?

253 views

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...