I need torque sequence for rod bearing caps

The torque specifications for the main bearings and connecting rod bearings in a Ford WL/WLT 2.5L Turbo engine may vary depending on the specific model year and engine configuration. However, as a general guideline, here are the torque specifications for the main bearings and connecting rod bearings in this engine:
Main bearings:

1. Torque the main bearing cap bolts in three stages in the following sequence:Stage 1: 30 Nm (22 lb-ft)
   Stage 2: 80 Nm (59 lb-ft)
   Stage 3: 90 degrees
2. After the final torque of 90 degrees, check the bolt stretch with a torque angle gauge. The stretch should be between 0.15mm and 0.30mm.

Connecting rod bearings:

1. Torque the connecting rod cap bolts in two stages in the following sequence:Stage 1: 30 Nm (22 lb-ft)
   Stage 2: 90 degrees
2. After the final torque of 90 degrees, check the bolt stretch with a torque angle gauge. The stretch should be between 0.15mm and 0.30mm.

It is important to note that these torque specifications are general guidelines and may vary based on the specific model year and engine configuration. Always refer to the manufacturer's service manual or consult a certified mechanic for the exact torque specifications for your specific vehicle

1. Tighten the cylinder head bolts in the sequence shown. Using the 4 step torque turn method, tighten according to the following values:

• • Step 1: All to 34 Nm (25 ft. lbs.)
  • Step 2: All to 68 Nm (50 ft. lbs.)
  • Step 3: All to 68 Nm (50 ft. lbs.)

CAUTION: Do not use a torque wrench for the following step.
Step 4: Turn an additional 1/4 turn

• Step 5: Install and tighten bolts (1-10) in sequence shown, to 41 Nm (30 ft. lbs.) .

1. Tighten bolts (1-10) again to 41 Nm (30 ft. lbs.) PLUS 1/4 turn in sequence shown.
2. Install main bearing bedplate to engine block bolts (11-20), and torque each bolt to 28 Nm (20 ft. lbs.) in sequence shown.

Connecting Rod Cap Bolts 54 Nm (40 ft. lbs.) + 1/4 turn
1997 Jetta: Torque settings..vw..the head, fly wheel, big ends.


1997 Jetta3 1800 feul injection


Vibration Damper/belt Pulley
Tighten 20 Nm (14.8 ft lb) Crankshaft Toothed Belt Sprocket Tighten 90 Nm (66 ft lb) + 90° Camshaft Sprocket Tighten 80 Nm (60 ft lb) Main Bearing Cap
Tighten 65 Nm (48 ft lb) FLYWHEEL TORQUE
Torque 60 Nm. (44 ft. lbs.) + 1/4 turn (90°) [1] [1] Always replace bolts.
CYLINDER HEAD TIGHTENING TORQUE [1] :
1st sequence: 40 Nm (30 ft lb)
2nd sequence: 60 Nm (43 ft lb)
Final sequence: plus 1/2 turn (180°)
Here are some additional specifications, thanks
ntake Manifold
Mounting Bolts 25 Nm (18 ft. lbs.) Bearing Cap Nut 20 Nm (15 ft. lbs.) Rod Bearing Cap
Assembly
Tighten 30 Nm (22 ft lb) + 90° To measure radial clearance
Tighten 30 Nm (22 ft lb) but NOT additional 90° TIGHTENING SPECIFICATIONS
Oil Pump Bolt 20 Nm (14 ft. lbs.) Oil Tube To Block 10 Nm (7 ft. lbs.) Exhaust Manifold to Cyl. Head 25 Nm (18 ft lb) Exhaust Manifold to Front Exhaust Pipe 40 Nm (30 ft lb) Water Pump
TIGHTENING SPECIFICATIONS
Cover Bolts 10 Nm (7 ft. lbs.) Mounting Bolt and Studs 20 Nm (15 ft. lbs.) + 1/4 turn (90°) Pulley Bolts 25 Nm (18 ft. lbs.)

TIGHTENING SPECIFICATIONS
Connecting Rod Nuts:
Tighten In Two Stages:
First Stage 30 Nm (22 ft. lbs.) Second Stage turn an additional 90°(1/4 turn)

Details are here

https://www.justanswer.com/ford/ab7rz-2006-ford-taurus-3-0l-rod-main-bearing-cap-bolt-torque.html

https://www.google.com/search?q=2006+Ford+Taurus+engine+torque+settings

..

Here are the torque specs you requested:
MAIN BRG CAPS= 29FT/LBS THEN TIGHTEN AN ADDITIONAL 90 DEGREES in sequence(two step process)
ROD BEARING CAPS= 18 FT/LBS
CYLINDER HEAD BOLTS= 29FT/LBS + 90 degrees + another 90 degrees in sequence from the center out ward, (3 step process).
Please let me know if you have any questions

Torque Specs Database

Type: Dim: Length: Head: Nut Grade: 20 Ft-Lbs 240 In-Lbs 27.12 N-m Connects: Connecting Rod To Engine Block Years: All Vote Record: Vote Note: Vortec - Rod Cap Nuts - 2 Steps: 20 FtLbs; +70degs

http://ww2.justanswer.com/uploads/ZZdaryl/2009-06-14_153454_torque.pdf

Main Bearing Cap Bolt 4.3L Step 1 15 ft lbs (20) Step 2 Additional 73 Degrees

i don't know if that's correct for main bearing caps since another link states it's much higher

4 3 Vortec Piston Specs eHow

hopefully a GM guy will chime in to confirm the main bearing torque

the rod bearing torques are the same on all the other links

the specs for the 1991 prelude with a 2.1 engine are, the connecting rod caps are 34 ftlbs and the main bearing cap are 49 ft lbs, hope this helps,

Head bolts, 105-112 Foot pounds (Final torque)
Final torque must be reached in 3 equal steps. Recheck final torque in sequence.
Main Bearing Caps, Torque in sequence Step 1: torque to 50 Ft/Lbs Step 2: torque to 105 Ft/Lbs
Rod Bearing Caps, 45 Foot pounds (Final torque)

1997 Nissan/Datsun Truck Pickup 2.4L SFI 4cyl

The Main Bearing Cap Torque:
38 Foot pounds (Final torque)

The Rod Bearing Cap Torque:
Torque sequence:
Step 1: Torque to 10-12 Ft/Lbs
Step 2: Torque to 28-33 Ft/Lbs

Hope help with this (remember rated this post). TY for using Fixya.

Cylinder heat bolt torque:
Torque sequence --------- front | 7 3 1 5 | | 8 4 2 6 | --------- Step 1: Torque all bolts in sequence to 14 Ft/Lbs Step 2: Torque all bolts in sequence to 29 Ft/Lbs Step 3: Torque all bolts in sequence to 36 Ft/Lbs Step 4: in the sequence, loosen the cylinder head bolts three turns. Step 5: Tighten short bolt to 15 - 32 Ft/Lbs Step 6: Tighten long bolt to 30 - 36 Ft/Lbs Step 7: Tighten all bolt to 175- 185 degree note: Do not loosen all of the cylinder head bolts at one time. Each cylinder head bolt must be loosened and the final tightening prior on the next bolt in the sequence.
Main bearing torque:
Torque sequence: Step 1: torque bolts to 91 Ft/Lbs with the exception of the rear main bearing cap Step 2: torque rear main bearing cap bolts to 88 Ft/Lbs Step 3: torque brace bolts to 40 Ft/Lbs
Connecting rod torque:
Torque sequence Step 1: Torque to 29 Ft/Lbs Step 2: Turn an additional 90 degrees