Slight back and forth unwanted moment of power front buckets.

Question edited for clarity. It took me ages to work out what a 'ford probeim' is!
Question moved to Ford Probe category.

You can try, but I doubt they will fit. Sell the old ones on eBay.

https://www.google.com/search?q=ford+probe.+put+front+bucket+seats+in+the+back+seat

..

If ypu are talking about seat mounting, on bucket seats they only have two remove these move seat all the way back then tip seat forward to unhook front remove seat.

Hi Stacy:
Most seats are held in place by bolts that go through the seat frame base into the floor.
To remove the seat,
1) Slide it all the way back and remove the front bolts
2) Slide it all the way forward and remove the back bolts
3) Lift or tip the seat backwards and disconnect the wiring.

the black bar is to remove the seat. That's the only reason for it.

Hi, follow the instruction below......
Rear
See Figures 3, 4, 5 and 6

1. Remove the lower seat cushion by pulling straight up on the front portion and disengaging the clips. Then hinge the seat upward to release the rear clips.
   

Fig. 3: Pull up on the front of the lower seat cushion and disengage the clips

1. Remove upper rear seat back-to-chassis bolts.

Fig. 4: Remove the bolts behind the center armrest ...



Fig. 5: ... and the bolts on the lower corners ...



Fig. 6: ... Then pull up on the seat to disengage the three clips on the top of the seat

1. Remove rear seat back by tilting forward and pulling straight up.
   

To install:

1. Install the lower seat cushion and torque the lower rear seat-to-chassis bolts to 15-20 ft. lbs. (21-26 Nm).
2. Install the upper rear seat back cushion and torque the upper rear seat back-to-chassis bolts to 15-20 ft. lbs. (21-26 Nm)

Do they have a "T" like handle in front under seat? If so, lift handle and pull it forward to unlatch. Then lift seat slightly and slide it back to release rear catches. Hopefully they are still same as my 99.

On W-Body vehicles, the front seats are secured to the floorpan by two front hook attachments and two rear bolts installed to nuts welded to the floorpan.
The manually operated two-way front adjusters provides only fore and aft movement of the seat. When the seat adjuster handle located on the front seat is pulled up, the seat adjusters unlock, permitting travel of the seat. When the seat is in the desired position and the seat adjuster handle is released, the seat locks in place.
A power operated six-way seat adjuster is available. The adjusters are activated by three 12 volt, reversible, permanent magnet motors with a built-in circuit breaker. The motors are energized by a switch bolted on the seat side panel.
The three motors drive the front seat and rear vertical actuators and a horizontal actuator. When the adjusters reach the limit of travel, torque is absorbed through the rubber mounted grommets located between the motor and the support. An overload relay is provided in the circuit and will open should excessive stall be applied.
The optional 60/40 split bench front seats have seat back head restraints on the driver's and passenger's seat back. The head restraints are designed so they cannot be removed from the seat back without first inserting a small rounded tool inside the head restraint support tube to release the locking tab. The 60/40 split bench seat is equipped with a reclining mechanism on both the driver's and passenger's side. The recliner lever is located on the outboard side of the spring cushion. When the lever is pulled upward, the spring loaded dual linear reclining unit located in the cushion frame is released, allowing the seat back to be pushed rearward or allowing the spring loaded reclining unit to bring the seat back forward.
Bucket seats are equipped with manual reclining mechanisms. An optional six-way power seat adjuster is available. Some bucket seats are equipped with inertia seat back locks. This system allows the seat back to fold forward without requiring the occupant to release a locking lever or access to the rear seat area. During a sudden stop or deceleration, or if the front of the vehicle is nose down, the inertia system of the seat back lock will engage, holding the seat back in its rest position. A release lever is provided to allow manual release of the seat back lock when the vehicle is in the nose down position. The release lever is located at the lower rear outboard corner of the seat back.
Some W-Body vehicles (notably Pontiac coupes) have passenger front seats equipped with an E-Z Entry device. This is actuated, in an unoccupied seat, by completely folding the seat back forward disengaging the adjuster, and sliding the front seat forward to gain access to the rear seat area. To return the seat to its normal position, return the seat back to its rest position, and slide the entire seat rearward, engaging the adjuster.
W-Body rear seats are available in several styles including a rear seat with an integral child restraint device.

you will need a metric rachet and wrench to remove 4 bolts from the bottom of of the seat. the bolts is bolting down the rail which the seat is riding on. to get to the front bolt you need to slide the seat all the way back and to get the rear bolts, slide the seat all the way forward.
I hope that help a bit

i had the same prob when i got my durango.i set the seat where i was cumfortable and still where my wife could be cumfortable drilled two small holes on the side of the rail and shot two rivets through it.all the other controls work the same but it doesnt go back and forth anymore.works for me ,alot cheeper than a power seat.

the middle seats come out easily. There are 2 handles you have to lift up on each of the bucket seats, they are in the front of the seat down by the seat tracks. After you lift them, tilt the seat upward in the front and rotate them backward. Then lift out of the hooks. Each seat is held down by 4 hoks.

The 3rd row seat is not designed to come out xcept by a technician. It does slide forward all the way up to the front seat. It has a sliding seat track.
First, lift the T handle under the seat cushion on the left front side of the seat. This will allow you to lift the seat bottom up all the way to lcok in the full up position.
Then, lift the lever on the same side of the seat and slide the seat forward. It will stop in 4 places.
Rear -Rear
6 inches forward of that.
another two ft to the second row seating position
full frward against the front seats.

Pleae rate as fixya if this helps.

Seat —Third Row Bench Removal
CAUTION: Removal of the third row bench seat requires more than one technician.

1. Remove the second row seats. For additional information, refer to Seat—Second Row .

1. Remove the floor mats.

1. Lock the seat cushion in the upright position.
   1. Lift the handle to release the cushion.
   1. Lock the seat cushion in the upright position.

1. Move the third row bench seat to the second row position.
   • Lift the seat track release handle.

1. Remove the two bolt covers.

1. Remove the two seat track front bolts.

1. Remove the four seat track rear bolts.
   1. Position the rear seat cushion floor cover aside.
   1. Remove the four seat track rear bolts.

1. Remove the third row bench seat.