Question about 1998 Chevrolet Chevrolet silverado

1 Answer

Replacing oil pan gasket 1998 chevy silverado 305 cu.in.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Wolfpack:

    An expert that has 5 followers.

  • Expert
  • 102 Answers

REMOVAL PROCEDURE

  1. Remove the oil level indicator tube.
  2. Raise the vehicle.
  3. Remove the engine oil and the engine oil filter.
  4. Remove the oil filter adapter.
  5. Remove the starter.
  6. Remove the flywheel inspection cover.
  7. Remove the engine mount through bolts.
  8. Raise and support the engine.




  1. Remove the oil pan nuts and bolts. Note the location of any studs to assist reassembly.
  2. Remove the engine oil pan and the gasket.
  3. Clean all sealing surfaces. Refer to Oil Pan Clean and Inspect under Engine Unit Repair.
INSTALLATION PROCEDURE


  1. Install the engine oil pan and a NEW gasket. Refer to Oil Pan Installation under Engine Unit Repair.
  2. Lower the engine onto the mounts.
  3. Install the engine mount through-bolts.
  4. Install the starter.
  5. Install the flywheel inspection cover.
  6. Install the engine oil filter and the engine oil.
  7. Install the oil filter adapter.
  8. Install the oil level indicator tube.

Posted on May 05, 2015

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 3 Answers

SOURCE: To change the oil pan gasket in a 93 Tercel

is not hard, i changed mine 95 tercel

Posted on Oct 24, 2008

Anonymous

  • 5 Answers

SOURCE: 2000 Chevy Blazer

i am working on a s 10 of the same yaer and problem i will post my results after tomorrow when i have finished the job i bout this truck cause of the forum i own one that is a great one and this one is for experimental purpose i will let u know so far you cant lift the motor with a jack or a hoist so we r going another route in the mornin

Posted on Dec 27, 2008

MrScary66613

Travis Humphries

  • 1990 Answers

SOURCE: Oil Pan Gasket Replacement - How to - GMC Yukon 2000

No big job Really. Just locate your Drain Plug for the Oil. Thepan is right there, Remove the Bolts around the Pan and Remove. You will lose all of your oil so, Have something there to catch it all. Clean it all around the Edges of the Block where the Pan mounts with Degreaser and Make sure that you Scrape the Old Gasket off of Both the Block and the Pan. Run a Thin Bead of Blue ATV Silicone around the Pan Edge, Lay the Gasket on top of this Silicone. Put another Thin line on top of the Gasket and Reinstall. This Silicone is High Temp Silicone and will Seal Very Well. Make sure to put oil Back in the Motor! Please Rate my Response, I need all the Help That I can Get! Thanks!

Posted on Jan 27, 2009

Anonymous

  • 82 Answers

SOURCE: 2001 Silverado oil pan gasket is it hard to

It's a question of access. Look underneath vehicle for any obstructions (Otherwise, obstructions must be removed first, e.g. support brace, splash shield, stabilizer, etc, ...). If you can see entire pan and all bolts, just drain oil and remove pan . Remove old gasket. Clean both surfaces. Install new gasket. Use high temp RTV (red). Replace oil pan. Hand tighten bolts. Then use correct torque and torque pattern.

Posted on Jul 10, 2009

Anonymous

  • 92 Answers

SOURCE: To change the oil pan gasket in a 93 Tercel

Stock the car doesn't come with an oil pan gasket but you can order one from rockauto.com you don't have to remove the A/C compressor for any of the jobs you listed. If you want to change the timing belt you need to remove the plastic rock guard under the motor on the passenger side. remove the spark plugs and using the socket turn the engine from the crankshaft clockwise until you are at TDC on #1 cyclinder. (compression stroke) Next remove the upper and lower plastic timing belt covers. The idler pulley is the one with the spring. Loosen the nut and remove the spring then you can remove the timing belt. It really isn't that hard to do. Maybe one afternoon.

Posted on Sep 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change the oil pan gasket on a chevy silverado 2001 4x4 1500hd


remove or roll front diff. forward. unbolt pan and lower bellhousing to pan bolts and then remove pan.

Jan 31, 2014 | 2001 Chevrolet Silverado 2500HD

1 Answer

1998 chevy s10 ****** pan depth


there is only one pan casket 2.2 or 4.3 is still the same for the transmission for the oil pan( os34300c felpro )

Apr 19, 2013 | 1998 Chevrolet S-10 Pickup

1 Answer

1999 chevy silverado 5.3 engine oil pan has water in it


That's really bad if the antifreeze has made it into the oil pan.It'll wipe your rod and main bearings quickly.
Might be the dreaded head gasket problem. don-ohio

Oct 21, 2011 | 1999 Chevrolet Silverado 1500

1 Answer

I have a 07 Chevy Silverado w/ 5.3L. I presently have 105k on it and have noticed that in the last 12 months, my oil consumption has increased dramatically. Following the oil life monitor since my last...


double check for leak at rear of engine where engine block mates the transmission .the housing for the rear seal is bad about leaking on these engines at 100,000 miles

Dec 25, 2010 | 2007 Chevrolet Silverado 1500 2WD

2 Answers

I have no oil pressure on the gauge on the dash board and it is leaking oil under neath the engine what could it be. 97 chevy silverado 2500 4by4


Could be a broken oil pressure sending line or something worse.... Hole in oil pan, broken/missing (blown-off) oil filter.

Sep 27, 2010 | Chevrolet Silverado 2500 Cars & Trucks

1 Answer

What is involved with replacing the oil pan on 1998 GMC Sierra?


  • Step 1 Raise the truck using the proper equipment. Use a ramp or a jack and jack stands to support the vehicle securely by following all directions for use provided by this equipment's manufacturer.
  • Step 2 Drain all oil from the Silverado by placing an oil drip pan under the vehicle's engine block, directly under the oil drain plug. The drain plug is located on the oil pan, between the vehicle's tires underneath the vehicle. Use a wrench to loosen and remove the plug allowing the oil to drain into the pain below.
  • Step 3 Notice the various items attached to the oil pan or in the way of the oil pan dropping. For the oil pan to drop, remove the negative battery cable, front differential (only for four-wheel drive vehicles) and the under body shield by using a wrench or socket set.
  • Step 4 Remove the oil pan shield by loosening the four bolts holding it in place along the edges of the shield. Then, remove the cross brace, oil filter, the transmission to oil pan bolts and the oil level sensor.
  • Step 5 Follow the removal of those pieces by removing the bolts from the two front wiring harness, the engine wiring harness retainer, engine oil cooler pipe to oil bolts and the transmission oil cooler pipe retainer using a wrench. Located the closeout covers and bolts located on each side of the engine and remove them.
  • Step 6 Disconnect each of the oil pan bolts using a wrench that will allow the oil pan to drop. The oil pan gasket will also fall off and replacement should occur before reinstalling the oil pan.


  • Read more: How to Drop the Oil Pan in a Chevy Silverado | eHow.com http://www.ehow.com/how_4508109_drop-oil-pan-chevy-silverado.html#ixzz0wi82Ul2u

    Aug 15, 2010 | GMC Sierra 1500 Cars & Trucks

    1 Answer

    Oil leaking on my mufflers of my 85 c10 chevy silverado. and i already changed the oil pan gasket


    it could be a few things oil sending unit /intake gasket/valve cover gasket/ rear oil seal /I would wash the engine and look starting from top down

    Mar 30, 2010 | 1983 Chevrolet Silverado

    2 Answers

    Bad oil leak by the starter on my 1988 chevy k1500 (305)


    Could be the oil pan gasket or the rear main oil seal.
    Remove the torque convertor cover. ( I am assuming that your truck is an automatic) That's that thin metal cover between the engine and transmission on the bottom side.
    Drive the truck around the block to warm up and the oil to start leaking.
    With the engine running in neutral, emergency brake on and wheels choked for safety.
    Crawl under the truck and see where exactly the leak is. Is it between the flywheel and the engine block --leaking straight down the center of the flywheel --crankshaft rear seal?Or the pan gasket? or even a oil galley plug?
    Good Luck.

    Feb 06, 2010 | 1988 Chevrolet K1500

    1 Answer

    Oil pan gasket replacement


    It shouldn't be hard on that car as the oil pan is exposed. Unplug the oil plug and drain the oil. Then unbolt the oil pan, clean off the old gasket and replace. Make sure you scrape both the pan and the block clean thoroughly and then bolt back up. Don't forgot to replug the drain plug.

    Mar 12, 2009 | 1998 Plymouth Grand Voyager

    1 Answer

    Changed oil pan gasket now i dont have much oil pressure


    If oil pressure was fine before you changed the gasket, it's likely that some debris was loosened up (probably under the pan baffle) and got onto the oil pump pickup, restricting flow. The only other cause of low pressure would be worn engine bearings, which would not happen just by changing oil pan, unless you messed with either bearings or pump while pan was down. Remove the pan and carefully inspect the pump pickup for debris!!! DO NOT DRIVE VEHICLE 'TILL YOU HAVE CORRECTED THIS OR YOU WILL DAMAGE BEARINGS!!!

    Feb 19, 2009 | 2000 Chevrolet Silverado 1500

    Not finding what you are looking for?
    1998 Chevrolet Chevrolet silverado Logo

    677 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    Marvin
    Marvin

    Level 3 Expert

    85222 Answers

    Jonah Oneal

    Level 3 Expert

    14092 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22485 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...