2003chevy s10 4x4,where is the evap canister and evap system curcuit?

DTC P0497: Evaporative Emission (EVAP) System No Flow During Purge
Circuit/System Description
The control module tests the evaporative emission (EVAP) system for a large leak, or a stuck closed EVAP canister purge valve. The control module monitors the fuel tank pressure (FTP) sensor signal to determine the EVAP system vacuum level. When the conditions for running are met, the control module commands the EVAP canister purge valve OPEN and the EVAP vent valve CLOSED. This allows engine vacuum to enter the EVAP system. At a calibrated time, or vacuum level, the control module commands the EVAP canister purge valve closed, sealing the system, and monitors the FTP sensor input in order to determine the EVAP system vacuum level. If the system is unable to achieve the calibrated vacuum level, or the vacuum level increases too slowly, a DTC sets.

Diagnostic Aids
• A loose, missing, or damaged fuel fill cap can cause this DTC to set.
• A stuck closed, blocked, or restricted EVAP canister purge solenoid valve, can cause this DTC to set.
• A blockage or restriction in the EVAP canister purge solenoid valve vacuum supply hose, EVAP canister purge solenoid valve purge pipe, EVAP canister, or vapor pipe, can cause this DTC to set.
• A temporary blockage in the EVAP canister purge solenoid valve, purge pipe or EVAP canister could cause an intermittent condition. Inspect and repair any restriction in the EVAP system.
• To help locate intermittent leaks, use the J 41413-200 Evaporative Emissions System Tester (EEST) to introduce smoke into the EVAP system. Move all EVAP components while observing smoke with the J 41413-SPT High Intensity White Light. Introducing smoke in 15 second intervals will allow less pressure into the EVAP system. When the system is less pressurized, the smoke will sometimes escape in a more condensed manner.
• To improve the visibility of the smoke exiting the EVAP system, observe the suspected leak area from different angles with the J 41413-SPT .
• Observe the Freeze Frame/Failure Records vehicle mileage since the diagnostic test last failed may help determine how often the condition occurs that caused the DTC to set. This may assist in diagnosing the condition.

No these are 2 different fault codes, although they are related to the same system
EVAP control system does not operate properly.
- EVAP control system has a leak in the line between intake manifold and EVAP control system pressure sensor.

Possible causes include ...
- EVAP canister purge volume control solenoid valve stuck closed.
- EVAP control system pressure sensor and its circuit.
- Loose, disconnected, or improper connection of rubber tube.
- Blocked rubber tube.
- Blocked or bent rubber tube to MAP/BARO switch solenoid valve.
- Cracked EVAP canister.
- EVAP canister purge volume control solenoid valve.
- Closed Throttle Position Switch.
- Improper connection of one-way valve.
- Blocked purge port.
- EVAP canister vent control valve.

DTC P0446: Evaporative Emissions (EVAP) Vent System Performance
Circuit/System Description
This DTC tests the evaporative emission (EVAP) system for a restricted or blocked EVAP vent path. The control module commands the EVAP canister purge solenoid valve Open and the EVAP canister vent solenoid valve Closed. This allows vacuum to be applied to the EVAP system. Once a calibrated vacuum level has been reached, the control module commands the EVAP canister purge solenoid valve Closed and the EVAP canister vent solenoid valve Open. The control module monitors the fuel tank pressure (FTP) sensor for a decrease in vacuum. If the vacuum does not decrease to near 0 inch H2O in a calibrated time, this DTC sets.
Diagnostic Aids
?€¢
An intermittent condition could be caused by a damaged EVAP vent housing, a temporary blockage at the EVAP canister vent solenoid valve inlet, or a pinched vent hose. A blockage in the vent system will also cause a poor fuel fill problem.

?€¢
An EVAP canister, vent hose, or vent solenoid valve that has restricted flow may cause this DTC to set. Using a purge solenoid command with a scan tool will allow vacuum to be applied to the system instead of pressure. With the engine running, the EVAP canister vent solenoid valve open, and the EVAP canister purge solenoid valve commanded to 100 percent, the fuel tank vacuum should not increase to more than 5 inches H2O.

?€¢
An EVAP canister filter that is restricted can cause this DTC to set. Refer to Evaporative Emission Canister Replacement .

?€¢
Disconnecting one component at a time while the EVAP system is under flow will help to pinpoint a restriction in the system

Do you have a scan tool that reads data PID'S ?
Your FTP - fuel tank pressure sensor could be at fault !

Ignition ON and fuel cap removed, verify that the FTP sensor parameter is between 1.3-1.7 volts. ?‡'
If not within the specified range, go to the FTP sensor section in Circuit/System Testing.

1. Install the fuel cap.
2. With the engine running, the EVAP canister vent solenoid valve open, and the EVAP canister purge solenoid valve commanded to 100 percent, the fuel tank vacuum should not increase to more than 12 inches H2O.

?‡'
If the fuel tank vacuum is greater than the specified range, go to the restriction section in Circuit/System Testing.

If

Error Code: P0440
Fault Location:
Evaporative Emission (EVAP) System - Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
Soution:
Check Evaporative Emission (EVAP) System Sealing.
Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve .

Error Code: P0441
Fault Location:
Evaporative Emission (EVAP) System - Incorrect Flow Detected
Possible Solutions:
Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
Perform Output Test.
Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve .
Check Evaporative Emission (EVAP) Canister.
Perform Basic Setting.
Check Pipes between Tank Breathing and Throttle Body.

Error Code: P0446
Fault Location:
Evaporative Emission (EVAP) System, Vent Control - Circuit Malfunction
Possible Cause:
Wiring harness.
Evaporative emission (EVAP) canister purge valve.
Engine control module (ECM).

This Pinpoint Test is intended to diagnose the following:

• Canister vent (CV) solenoid (9F945) (electrical concern only)
• Fuel filler cap (9030)
• Fuel tank pressure (FTP) sensor (9C052)
• EVAP canister tube (fuel tank to EVAP canister)(9A228)
• Fuel canister purge outlet tube (EVAP canister to EVAP canister purge valve) (9D661)
• EVAP return tube (EVAP canister purge valve to intake manifold) (9G271)
• EVAP canister purge valve (9C915)
• Vacuum source line (input port vacuum to intake manifold)
• Harness circuits: CV, FLI, FTP, EVAP Canister Purge Valve, SIG RTN, vehicle power (VPWR), reference voltage (VREF) and power ground (PWR GND)
• Powertrain control module (PCM) (12A650)

This Pinpoint Test is used as an assistance in diagnosing the following EVAP components:

• EVAP canister and bracket assembly (9E857)
  • EVAP canister sleeve assembly (fitting)(9D925)
  • Canister vent (CV) solenoid - hose assembly (9F976 or 9K318)
  • EVAP canister (9D653)
  • Canister vent (CV) solenoid (9F945)(mechanical concern only)
• Fill limit valve assembly (9A086)
• Fuel filler pipe flapper valve (9B085)
• Fuel filler pipe check valve (9189), assembly (9285)
• Fuel tank filler pipe (9034)
• Fuel tank assembly (with fuel vapor vent valve) (9K007)
• Fuel tank assembly (without fuel vapor vent valve) (9002)
• Fuel vapor control valve (9B190)
• Fuel vapor vent valve (9B593)
• Liquid/vapor fuel discriminator (9G332)
• On-board refueling vapor recovery (ORVR) T - connector assembly (9S314)

Description For additional information on the Evaporative Emission (EVAP) System, refer to Section 1A .
For additional information on the Evaporative Emission System Monitor, refer to Section 1A .
Pinpoint Test Schematics Escort/Tracer (2V)

P1443 Evaporative Emission Control System Control Valve The Evaporative Emission Control System monitors the fuel vapor flow between the engine intake manifold and the EVAP canister. The system failure occurs when a leak or blockage between the intake manifold, the EVAP canister purge valve and the EVAP canister is detected by the PCM.

Code P1443 Possible Causes:

- Pinched, blocked or plugged fuel vapor tubes/hoses (except between fuel tank and EVAP canister)

- Damaged EVAP canister

- Disconnected, cracked or cut fuel vapor tubes/hoses (except between fuel tank and EVAP canister)

- Damaged EVAP canister purge valve

EVAP System Vent Circuit Malfunction

This diagnosis detects leaks in the Evaporative Emission (EVAP) purge line using of vapor pressure in the fuel tank. The EVAP canister vent control valve is closed to shut the EVAP purge line. The vacuum cut valve bypass valve will then be opened to clear the line between the fuel tank and the EVAP canister purge volume control solenoid valve. The EVAP control system pressure sensor can now monitor the pressure inside the fuel tank. If pressure increases, the Engine Control Module (ECM) will check for leaks in the line between the vacuum cut valve and EVAP canister purge volume control solenoid valve.

Possible causes
- Incorrect fuel tank vacuum relief valve
- Incorrect fuel filler cap used
- Fuel filler cap remains open or fails to close
- Foreign matter caught in fuel filler cap
- Leak is in line between intake manifold and EVAP canister purge volume control solenoid valve
- Foreign matter caught in EVAP canister vent control valve
- EVAP canister or fuel tank leaks
- EVAP purge line (pipe and rubber tube) leaks
- EVAP purge line rubber tube bent
- Blocked or bent rubber tube to EVAP control system pressure sensor
- Loose or disconnected rubber tube
- EVAP canister vent control valve and the circuit
- O-ring of EVAP canister vent control valve is missing or damaged
- EVAP canister is saturated with water
- EVAP control system pressure sensor
- Absolute pressure sensor

Possible solution
- Loose fuel filler cap
- Leaking fuel filler cap


Hope helps (remember to rate this answer).

Here's list why your car is coming up with this code. It could be any of these things causing it.
DTC detecting condition:

• EVAP control system has a leak.
• EVAP control system does not operate properly.

Possible cause:

• Incorrect fuel tank vacuum relief valve
• Incorrect fuel filler cap used
• Fuel filler cap remains open or fails to close.
• Foreign matter caught in fuel filler cap.
• Leak is in line between intake manifold and EVAP canister purge volume control solenoid valve.
• Foreign matter caught in EVAP canister vent control valve.
• EVAP canister or fuel tank leaks
• EVAP purge line (pipe and rubber tube) leaks
• EVAP purge line rubber tube bent
• Blocked or bent rubber tube to EVAP control system pressure sensor
• Loose or disconnected rubber tube
• EVAP canister vent control valve and the circuit
• EVAP canister purge volume control solenoid valve
• EVAP canister purge volume control solenoid valve and the circuit
• Absolute pressure sensor
• Fuel tank temperature sensor
• O-ring of EVAP canister vent control valve is missing or damaged
• Water separator
• EVAP canister is saturated with water
• EVAP control system pressure sensor
• Refueling control valve
• ORVR system leaks
• Fuel level sensor and the circuit

evap emission control system fault-po441, po742 is--torque converter curcuit stuck on, for this code, check torque converter clutch switch..

Continuous Memory Diagnostic Trouble Code (DTC) P0442 indicates that a fuel vapor leak has been detected [as small as 0.10 cm (0.04 inch)] in the Evaporative Emission (EVAP) system.
Note: Prior to performing the following diagnosis inspect the Canister Vent Solenoid (CV) for contamination. A situation may exist where contamination holds open the Canister Vent (CV) solenoid enough to set DTC P0442 and also plugs the port to atmosphere enough to keep system from being vented quickly.

• After market parts and accessories nonconforming to the EVAP system specifications.
• Damaged, cross threaded or loosely installed fuel filler cap.
• Small holes or cuts in fuel vapor hoses/tubes (EVAP canister tube, EVAP canister outlet tube or EVAP return tube) in the EVAP system.
• Loose fuel vapor hose/tube connections to EVAP system components.
• EVAP system component [EVAP canister purge valve, fuel tank pressure (FTP) sensor, canister vent (CV) solenoid, fuel vapor control valve tube assembly or fuel vapor vent valve assembly] seals leaking.
• CV solenoid partially open when commanded closed.
• EVAP canister leaking.
• Check for presence of fuel filler cap.
• Verify that the CV solenoid is properly seated on the EVAP canister (if possible).
• Visually inspect for cut or loose connections to fuel vapor hoses/tubes in following locations:
  • EVAP canister to EVAP canister purge valve.
  • EVAP canister to fuel vapor vent valve assembly.
  • fuel vapor control valve tube assembly to fuel tank (if applicable).