VACUUM LINE DIAGRAM 97 DODGE TRANSMITION

Here is a general vacuum hose and line placement diagram for a 2001 Dodge Ram 1500 4x4:

1. The vacuum line from the engine intake manifold should be connected to the vacuum reservoir tank.
2. The vacuum line from the vacuum reservoir tank should be connected to the vacuum actuator on the front axle.
3. The vacuum line from the vacuum actuator on the front axle should be connected to the transfer case.
4. The vacuum line from the transfer case should be connected to the vacuum actuator on the rear axle.
5. The vacuum line from the vacuum actuator on the rear axle should be connected to the vacuum reservoir tank.

It is important to note that the specific placement and routing of vacuum hoses and lines can vary depending on the make and model of your Dodge Ram 1500, as well as any modifications that may have been made to the vehicle. It is always recommended to refer to the manufacturer's instructions or a repair manual specific to your vehicle for accurate information. Additionally, it may be helpful to take pictures or label the hoses and lines before removing them to ensure proper reinstallation.

Does a 2002 Dodge Ram 4x4 have a vacuum modulator ...

www.fixya.com/.../t25860408-2002_dodge_ram_4x4_vacuum_modulat...

14 mins ago - 1 Answer. Where do the vaccum lines go into the transfer case on a 2002 RAM 3500? I need a diagram of the vaccum lines into the transfer ...

Vacuum lines do not actually go into the transfer case, they go to the 4x4 actuator and there is a vent hose at the top...that is about it.

Power as in 12 V DC ? if yes, you are not in the correct area, the front axle is locked in and out of 4x4 mode with vacuum.

Operationally vacuum shifts the front axle between 2WD and 4WD mode. The GEM ( Generic Electronics Module ) applies ground to the solenoid needed for the mode selected on the switch ( for ESOF ) or when the transfer case shift lever is moved ( MSOF ).The contact plates in the transfer case signal the GEM that the transfer case is engaged, and the Vacuum solenoids need to be activated ( either 2WD to 4WD or 4WD to 2WD ).


Lift and support the front of the truck so the front wheels are off the ground ( take safety precautions, chock wheels, jack stands, etc )
Key on, engage 4x4 and try to turn the front drive shaft.
- If it turns it is a problem with the transfer case.
- If it doesn't it is a front axle engagement problem.

- If the front drive shaft does not turn :
•With the truck running ( with front wheel back on the ground ), switch from 2WD to 4WD and back again, the vacuum shift motor should move the lever on the front axle.

Item #10 in this diagram

-- If the vacuum shift motor does not move:
1.Check for vacuum on the lines while shifting between modes. Pink vacuum line is 2WD mode, Light Blue vacuum line is 4WD.
2.Check the fuses for the 4WD system and the solenoids.
3.Check the vacuum lines from the vacuum shift motor to the solenoids on the firewall.
4.Check the vacuum lines from the solenoids to the vacuum reservoir box behind the battery.
5.Check the vacuum reservoir box for cracks.
6.Typical solution is the vacuum lines ( to the solenoids or to the vacuum shift motor ) are cracked or the vacuum shift motor has a cracked diaphragm and has water in it.
7.Could be the shift plate contacts in the transfer case are corroded / not making good contact, and not activating the solenoids.


- If the front drive shaft turns:
For ESOF system
-- Check the fuses for the transfer case, engine compartment fuse panel, 17 & Cab fuse panel fuses 13 and 23 ( verify with owners manual, 97-97 & 99-03 MY can be slightly different on some items ).
-- Try hitting the transfer case with a dead blow hammer ( do not use a metal hammer, it can damage the transfer case ) to see if the transfer case shift motor is hung up .
-- Check the transfer case connector, to make sure the connector pins are clean and making good contact.
For MSOF systems
-- Check that the shift linkage on the transfer case is moving when the lever is moved from 2W to 4H and 4L.

Operationally vacuum shifts the front axle between 2WD and 4WD mode. The GEM ( Generic Electronics Module ) applies ground to the solenoid needed for the mode selected on the switch ( for ESOF ) or when the transfer case shift lever is moved ( MSOF ). The contact plates in the transfer case signal the GEM that the transfer case is engaged, and the Vacuum solenoids need to be activated ( either 2WD to 4WD or 4WD to 2WD ).

Lift and support the front of the truck so the front wheels are off the ground ( take safety precautions, chock wheels, jack stands, etc )
Key on, engage 4x4 and try to turn the front drive shaft.
- If it turns it is a problem with the transfer case.
- If it doesn't it is a front axle engagement problem.

- If the front drive shaft does not turn :
•With the truck running ( with front wheel back on the ground ), switch from 2WD to 4WD and back again, the vacuum shift motor should move the lever on the front axle.
{ picture of shift motor }
-- If the vacuum shift motor does not move:
•Check for vacuum on the lines while shifting between modes. Pink vacuum line is 2WD mode, Light Blue vacuum line is 4WD.
•Check the fuses for the 4WD system and the solenoids.
•Check the vacuum lines from the vacuum shift motor to the solenoids on the firewall.
•Check the vacuum lines from the solenoids to the vacuum reservoir box behind the battery.
•Check the vacuum reservoir box for cracks.
•Typical solution is the vacuum lines ( to the solenoids or to the vacuum shift motor ) are cracked or the vacuum shift motor has a cracked diaphragm and has water in it.
•Could be the shift plate contacts in the transfer case are corroded / not making good contact, and not activating the solenoids.
{ Picture of Vacuum diagram )

- If the front drive shaft turns:
•For ESOF system
-- Check the fuses for the transfer case, engine compartment fuse panel, 17 & Cab fuse panel fuses 13 and 23 ( verify with owners manual, 97-97 & 99-03 MY can be slightly different on some items ).
-- Try hitting the transfer case with a dead blow hammer ( do not use a metal hammer, it can damage the transfer case ) to see if the transfer case shift motor is hung up .
-- Check the transfer case connector, to make sure the connector pins are clean and making good contact.
•For MSOF systems
-- Check that the shift linkage on the transfer case is moving when the lever is moved from 2W to 4H and 4L.

Operationally vacuum shifts the front axle between 2WD and 4WD mode. The GEM ( Generic Electronics Module ) applies ground to the solenoid needed for the mode selected on the switch ( for ESOF ) or when the transfer case shift lever is moved ( MSOF ).The contact plates in the transfer case signal the GEM that the transfer case is engaged, and the Vacuum solenoids need to be activated ( either 2WD to 4WD or 4WD to 2WD ).


Lift and support the front of the truck so the front wheels are off the ground ( take safety precautions, chock wheels, jack stands, etc )
Key on, engage 4x4 and try to turn the front drive shaft.
- If it turns it is a problem with the transfer case.
- If it doesn't it is a front axle engagement problem.

- If the front drive shaft does not turn :
•With the truck running ( with front wheel back on the ground ), switch from 2WD to 4WD and back again, the vacuum shift motor should move the lever on the front axle.
{ picture of shift motor }
-- If the vacuum shift motor does not move:
•Check for vacuum on the lines while shifting between modes. Pink vacuum line is 2WD mode, Light Blue vacuum line is 4WD.
•Check the fuses for the 4WD system and the solenoids.
•Check the vacuum lines from the vacuum shift motor to the solenoids on the firewall.
•Check the vacuum lines from the solenoids to the vacuum reservoir box behind the battery.
•Check the vacuum reservoir box for cracks.
•Typical solution is the vacuum lines ( to the solenoids or to the vacuum shift motor ) are cracked or the vacuum shift motor has a cracked diaphragm and has water in it.
•Could be the shift plate contacts in the transfer case are corroded / not making good contact, and not activating the solenoids.


- If the front drive shaft turns:
•For ESOF system
-- Check the fuses for the transfer case, engine compartment fuse panel, 17 & Cab fuse panel fuses 13 and 23 ( verify with owners manual, 97-97 & 99-03 MY can be slightly different on some items ).
-- Try hitting the transfer case with a dead blow hammer ( do not use a metal hammer, it can damage the transfer case ) to see if the transfer case shift motor is hung up .
-- Check the transfer case connector, to make sure the connector pins are clean and making good contact.
•For MSOF systems
-- Check that the shift linkage on the transfer case is moving when the lever is moved from 2W to 4H and 4L.

the range rod in the transfer case might not be moving the vaccum switch to switch

you sure its not the breather tube for the t-case. about 3/8 hose if it is. the vacuum lines for the 4x4 are small plastic lines. red, blue, yellow, etc. think there are four of them

It sounds like you may have vacuum problem. There are several places you need to check. FIrst check the vacuum line from the engine to the tranfer case. Then check the vacuum lines from the transfer case to the front differntial. If all lines check good, there is a vacuum swith on the top of the transfer case that may be the cuase of your problem.