Question about 1996 Ford Crown Victoria

1 Answer

How can I tell motor mounts are broken on crown victoria

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 53,770 Answers

Basically pull the motor off the mount
if it is broken then the mount will part
inspection will reveal a shiny part of metal where the rubber is rubbing on the steel

Posted on Jul 13, 2015

Ad

1 Suggested Answer

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I tell if my crown victoria motor mounts are broken


You need to open the hood. You can have someone stand by the fender and look at the engine while you do this test. Now start the engine and put it into drive gear, apply the brake and step on the accelerator pedal to bring the RPM up a little. The helper must watch how much the engine as it lifts or twists. More than an inch or two you have a broken mount. Now do the same thing in reverse gear to check the other side. This vehicle is a rear wheel drive and will have 3 motor mounts. Left , right (both under the exhaust manifolds) and a rear mount at the rear of the transmission. This mount should be visually checked as well. I hope this helps.

Jul 12, 2015 | 1996 Ford Crown Victoria

1 Answer

How can I tell motor mounts are broken


start the car and with the brakes applied put trans in forward gear and push on the throttle and if the engine raises the mount on the side the engine raises is the side the mount is broken. then put it in reverse and do the same thing if the engine raises then that mount is broken.

Jul 12, 2015 | 1996 Ford Crown Victoria

2 Answers

How can I tell if my motor mounts are broken


Raise car put on stands. Jack engine slightly toward one side and inspect mount. Do same for other side.

Jul 12, 2015 | 1996 Ford Crown Victoria

1 Answer

How do i replace the motor mounts on my 1994 crown


I can only forewarn you about several things to watch for in hope of providing you with something to prevent you from breaking something.
You must also consider loosening the transmission mounts to free up the entire drivetrain. There may be some clearance problems at the rear of the motor and the Radiator hoses may not stretch, nor may the fixed A/C lines to the front A/C cooler allow much travel space.
The oil pan is not a lifting point, nor is the crankshaft pulley. The exhaust system is not flexible either.
Your best bet is to look at the actual motor mount and see whether the mount is flush or has protruding studs. Flush shaped will be easier to handle. An 1/4 inch of clearance would allow you to slide parts through the opening.
You could still get another Expert to answer. I owned a 1994 Crown Vic and was underneath it many times, but never changed a motor mount on it.

Oct 02, 2014 | 1994 Ford Crown Victoria

1 Answer

'95 Ford Crown VIctoria left rear door motor runs but window will not go up and down.


It sounds like the power window motor is still running but you have a problem with the regulator arm. If you remove the door trim panel and water shield you can have a look to see where it has been disconnected from the motor or if the regulator arm itself is broken.

Feb 21, 2011 | 1995 Ford Crown Victoria

1 Answer

I have a 1995 crown victoria and the turn signals stay lit and autozone said i needed a flsher. so i got a cylinder flsher and it wont fit into my fuse block properly with the fuse block cover over it. can...


For 1995 Ford Crown Victoria 4.6L SFI 8cyl, the Flasher is located: Front seating area, driver side, under dash, driver side of pedal support bracket, mounted in fuse panel.

Hope helps with this.

Dec 06, 2010 | 1995 Ford Crown Victoria

1 Answer

Ware is the wiper module located on a 2000 crown victoria


Follow the Dark Blue/White wire or Brown/White wire from the Multifunction Switch to the wiper module according to the schematic.
Also, one can trace the wires from the windshield wiper motor to the wiper module by peeling away the wiring loom and looking for a Yellow/Red wire that leads to the module.
---
Windshield Wiper Motor Removal & Installation To Remove:
  1. Remove the mounting arm and pivot shaft assembly.
  2. Remove the windshield wiper motor cover.
  3. Remove the clip.
  4. Disconnect wiper transmission linkage.
  5. Remove the bolts.
  6. Remove the motor.
To Install:
  1. Position the wiper motor.
  2. Install bolts. Tighten to 10 Nm (89 in. lbs.).
  3. Connect wiper transmission linkage.
  4. Install clip.
  5. Install wiper motor cover.
  6. Install mounting and pivot shaft assembly.
prev.gif next.gif

Oct 28, 2010 | 1999 Ford Crown Victoria

1 Answer

1993 crown victoria drives said window wont roll and it not the motor please tell me what i can do


Check the fuse and wiring to the motor with a multimeter or test light while trying to operate power windows.

Take the panel off first to get at the motor to test for current.

Jul 11, 2010 | 1993 Ford Crown Victoria

2 Answers

When turned off, my 1998 Crown Victoria wipers park in the full upright position. How do I fix this?


replace the wiper motor, the park position is broken, need to replace complete wiper motor.

Jan 21, 2010 | 1998 Ford Crown Victoria

1 Answer

Transmission Mount is broken


Check the frame crossmember at the mount. If it looks like the crossmember can be unbolted, it should be a simple job. You would remove the crossmember while supporting the tailshaft. Then unbolt the trans mount from the transmission, change out the parts and reinstall. Or have a shop put it on a lift and change it out in less than an hour.

May 30, 2009 | 2004 Ford Crown Victoria

Not finding what you are looking for?
1996 Ford Crown Victoria Logo

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...