I tried to put a 2001 chevy suburban 2500 in four

Chevrolet Suburban Questions - 4 wheel drive does not ...

www.cargurus.com > Questions > Chevrolet > Suburban

CarGurus4 wheel drive does not work - When I put the Sub in 4 wheel drive, low of high, ...Asked by Robert_Holland_073 Dec 17, 2009 at 04:06 AM about the 1994 Chevrolet Suburban K1500 4WD ... it can seize up and then the trans case may ingage but the hubs won't be locked in so it ... 1999 Chevrolet Suburban K2500 LT 4WD.

Chevrolet Tahoe Suburban 4 Wheel Drive Indicator Lights - Car ...

forums.edmunds.com > Chevrolet > Chevrolet Suburban

Oct 2, 2007 - 31 posts - ‎19 authors
My 1999 Tahoe (odo reading 137,400 miles) won't go into 4 wheel drive. .... I have a 98 suburban 1500 4x4 LT 5.7 L with 165,000 miles ... I recall once forgetting todisengage 4WD and I could feel a terrific binding when I ...
Step by Step Troubleshooting 4wd 4x4 88-98 Chevy GMC ...? 21:32https://www.youtube.com/watch?v=Su9Dkrfd_ZgJan 20, 2014 - Uploaded by rwdellingStep by Step Troubleshooting 4wd 4x4 88-98 Chevy GMC Truck. rwdelling .... Mine is acting like it is NOT pulling with the fronts,won't engage. ... Have you ever adjusted or the shift cable on your 1500 Chevy ... GM 246 transfer case, 2000 Chev Suburban- Duration: 20:09. by spelunkerd 286,045 views.GM Troubleshooting Part 13 - 4WD vacuum actuator & cable ...? 5:11https://www.youtube.com/watch?v=CbEF6PyJdU0Feb 3, 2011 - Uploaded by mr diyguy123I tacked on this video about the 4wd sys. ... I have a 1994 ChevyS10 ... My S10 won't let you go to 4 LO when your in gear. ... the front end to keep them disengaged. when you put it in 4wd, the vacuum actuator pushes a gear ...

Are you sure it completely disengaged from four wheel drive ?

check the vacuum lines to the actuator in the front wheels . check the actuator operation in the transfer case.

Hi,
If you have a Four-Wheel Drive Suburban, it sounds like it's in 4WD HIGH. Check the switch on the dash and change to AWD or 2WD....do not use the 4WD Low (unless you're stuck in mud).
Td

If you have a lot of miles on it your 4wd trans.

drive in reverse for 20 feet. if that doesn't work try disconnecting the battery neg first for a couple min hit your 2wd button.

As I recall the 96 blazer had electronic shifting for 2wd to 4wd. There should be a small panel on the drivers dash buttons for 2wd, 4wd lo and 4wd hi.

Simply press the desired button while stationary and if the system is functioning properly then it will shift and the light for the engaged type of drive will be lighted. Generally you would like to be in 2wd for this vehicle.

There is an electrical conection called a servo and this might need to be replaced. It actuates the 4 wheel drive when the button is depressed

You probably have a bad encoder motor.It is located on the side of the transfer case on the drivers side.It is black.The other problem they had with these was the switch but you have already replaced this so your next thing is the encoder motor.Hope this helps.Good luck.

Your blazer is equipped with a shift on the fly four wheel drive. That means that at speeds less than fifteen miles per hour you can shift into or out of four wheel drive by simply pushing the four wheel high button. If you wish to shift into four wheel low. Stop, put the transmission into park or neutral, and push the four wheel low button. Same procedure for shifting back out. Never shift into or out of four wheel low while moving. And be careful in four wheel low. At full throttle your still barely moving, you don't want to blow your engine up!