Where is the fuse for wipers - 1994 Ford Crown Victoria

HI, turn off everything ,make sure wiper switch is in off position, unplug the wire connector to the wiper motor(install new fuse) turn key on, turn wiper switch on to first position then proceed till you have went thru all settings , then turn key off , turn switch off , check fuse/ blown fuse>>replace switch/ good fuse/ plug wire connector to wiper motor , turn key on turn wiper switch on to first position then proceed till you have went thru all settings ,wiper motor not wiping>>check fuse/blown fuse>> replace wiper motor/good fuse/ wiper motor not working>>> get a exorcist performed on it !!! <:0}

Do you know what a wiring diagram is ? A wiring diagram for your vehicles windshield wipers electrical circuit would show all components involved . You would need a wiring diagram for testing ,so you know which wires too test . It would show the fuse location - amperage etc.... Which of these is your vehicle - Notchback or hatchback or station wagon .

xTooltipElement
Service Information
2008 Holden Viva ' Optra, Viva (VIN J) Service Manual ' Body Systems ' Wipers and Washers ' Schematic and Routing Diagrams ' Document ID: 1964803
--------------------------------------------------------------------------------
Wiper/Washer Schematics
Figure 1: Wiper System - Notchback
Figure 2: Wiper System hatchback and Station Wagon
Figure 3: Wiper System Hatchback and Station Wagon w/Intermittent
Figure 4: Wiper System Notchback w/Rain Sensor
Figure 5: Wiper System Hatchback and Station Wagon w/Rain Sensor
Figure 6: Wiper System Hatchback and Station Wagon w/Intermittent and Rain Sensor
© 2019 General Motors Corporation. All rights reserved.

The fuse would be marked WPR fuse # 9 25 amp. located in the IP fuse panel . IP - instrument panel fuse box . It's location is
Fuse Block - I/P
Behind the left side of the I/P access panel
Windshield Wiper System
The windshield wiper system consists of a wiper motor, a linkage, a wiper arm and a blade, and a wiper/washer switch. The windshield wiper circuit incorporates a self parking device which consists of a worm gear and a cam plate in order to keep the circuit engaged temporarily when the switch is turned off. The wiper system is driven by a permanent magnet-type motor. The windshield wiper motor is mounted on the dash panel and is directly connected to the windshield wiper linkage.
The windshield wiper motor has 2 speeds, LO and HI, and also has intermittent wiper capability. The wiper switch is an integral part of the wiper/washer switch. Windshield wiper operation is actuated through the lever on the right side of the steering column.

https://www.youtube.com/watch?v=MvXX3Xg3siM

The wiper fuse for a 2015 Mitsubishi Mirage is located in the passenger compartment fuse box. The fuse box is located under the instrument panel on the left side, for left-hand drive cars. And on the right, for right-hand drive cars. The wiper fuse is labeled "WIPER" or "WINDSHIELD WIPER". It is a 15 amp fuse. To replace the wiper fuse, you will need a small flathead screwdriver. Open the fuse box cover. Locate the wiper fuse. Use the screwdriver to pry the wiper fuse out of the fuse socket. Install the new wiper fuse into the fuse socket. Close the fuse box cover. If your windshield wipers are not working, it is possible that the wiper fuse is blown. You can check the wiper fuse by looking at it. If the metal strip in the center of the fuse is broken, then the fuse is blown and needs to be replaced. You can also check the wiper fuse by using a multimeter. Set the multimeter to the "ohms" setting. Touch the positive lead of the multimeter to the metal strip on one end of the fuse. Touch the negative lead of the multimeter to the metal strip on the other end of the fuse. If the multimeter reads "0 ohms", then the fuse is good. If the multimeter reads "OL", then the fuse is blown and needs to be replaced. Once you have replaced the wiper fuse, your windshield wipers should start working again.

There are two relay's in the under hood fuse / relay box . Wiper relay an wiper relay 2 . Maybe one is bad . also check fuse #14 25 amp. Wiper fuse.Plus the BCM - body control module has a hand in making the wipers work . Are you familiar with automotive electronic control modules ?
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper micro relay
• Wiper 2 relay
• Wiper diode
• Windshield wiper motor
• Windshield washer pump
• Windshield washer nozzles
• Windshield washer solvent container
• Windshield wiper arm and blade assemblies
• Windshield wiper transmission
• WIP/WASH 10A fuse
• WIPER 25A fuse

Wiper/Washer System Description
The body control module (BCM) controls wiper motor low speed operation. The washer pump and high speed operation are controlled directly by the wiper/washer switch. The windshield wiper/washer switch supplies voltage on the signal circuits to the BCM for windshield wiper/washer operation. When WASH, MIST, DELAY, LOW, or HIGH is detected, the BCM energizes the wiper micro relay by suppling voltage to the relay coil. This allows battery voltage from the WIPER fuse to flow through the relay switched input then through the contacts and out the relay switched output to the wiper 2 relay switch contacts. Since the wiper 2 relay switch contacts are normally closed to the low speed circuit of the windshield wiper motor, the motor will operate at low speed.

Do you have any speed !

WPR fuse 25amp under hood fuse box .
Wiper/Washer System Components
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper PCB relay
• Wiper high PCB relay
• Windshield wiper motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR fuse 25 A
• WSW fuse 10 A
This is more then likely not a fuse issue !!!!!!!
Low Speed Operation
When the wiper switch is in the low speed position, ground is applied through the switch internal resistor and the wiper switch low signal circuit to the body control module (BCM). In response to this signal, the BCM energizes the WIPER PCB relay by applying battery voltage through the wiper relay control circuit to the coil side of the relay. This allows battery positive voltage from the WPR fuse to flow through the switch input side of the WIPER PCB relay and out to the switch input side of the WIPER HIGH PCB relay. Since the wiper high relay is de-energized and its switch contacts are normally closed to the low speed control circuit of the windshield wiper motor, the motor will operate at low speed.
Wiper motor low speed operation and the wiper PCB relay can also be commanded ON/OFF by using a scan tool. Refer to Control Module References.
The PCB relays mentioned above are soldered right into the circuit board inside the fuse/relay block under the hood . There are alot of reasons for the wipers not to work ! The fuse could be blown but fuse's don't just blow for no good reason , short to ground , low resistance high current flow etc.... Intermittant !

Power and Grounds
With the ignition in the ON position, accessory voltage is supplied through the 25A WPR fuse to the WIPER PCB relay, the WIPER HIGH PCB relay and the WS WASH PCB relay that are all located in the underhood fuse block. Refer to Wiper/Washer Schematics.
G200 provides ground for the windshield wiper motor and the WIPER PCB relay. G100 provides ground for the windshield washer fluid pump and the windshield washer fluid level switch.

What year ? The relay's are located in the under hood fuse box .
With the ignition in the ON position, accessory voltage is supplied through the 25A WPR fuse to the WIPER relay, the WIPER HI relay and the WSH relay that are all located in the underhood fuse block. Refer to Wiper/Washer Schematics. Which wipers are you talking about ? Front or rear . Rear wiper fuse is in the I/P instrument panel fuse box .
Fuse Block - I/P
Under the lower right side of the instrument panel

It can be faulty wiper motor or blown wiper control fuse.

Do you hear any kind of noise when you starter the wiper function. If yes then fuse is ok, but issue is wiper motor.

If no movement at all and no noise then its blown fuse or shorted/loose wiper control wiring:-----

For complete troubleshooting i suggest you few helpful links with accurate solutions.

-------------

Click the link below:-------

1993 Ford F350 wipers not working?

http://repairhelpcenter.blogspot.in/2012/02/1993-ford-f350-wipers-not-working.html

------------

How to Replace a Windshield Wiper Motor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-windshield-wiper-motor.html

------------

Wipers not working, but hear relay click on Lincoln LS?

http://schematicsdiagram.blogspot.com/2011/12/wipers-not-workingbut-hear-relay-click.html

-----------

Car windshield wiper gets power for movement and stops?

http://schematicsdiagram.blogspot.com/2011/12/car-windshield-wiper-gets-power-for.html

----------

How does cars Windshield Wiper System Works

http://technoanswers.blogspot.com/2011/11/how-does-cars-windshield-wiper-system.html

---------

1997 Honda Protege: Replace Wiper Transmission?

http://technoanswers.blogspot.in/2012/06/1997-honda-protege-replace-wiper.html

----------------

Windshield wiper fluid container leaking?

http://whatisbyme.blogspot.in/2012/05/windshield-wiper-fluid-container.html

-----------------

Where is wiper fuse located on1993 chevrolet suburban

http://technoanswers.blogspot.in/2012/02/where-is-wiper-fuse-located-on1993.html

------------

2002 Toyota Sienna: Wipers and Passenger side Power window stopped working?

http://technoanswers.blogspot.in/2012/04/2002-toyota-sienna-wipers-and-passenger.html

-------------

Complete wiper components replacing details for Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/complete-wiper-components-replacing.html

------------

These details will help.

Thanks.

It can be faulty wiper motor or blown wiper control fuse.

Do you hear any kind of noise when you starter the wiper function.If yes then fuse is ok,but issue is wiper motor.
If no movement at all and no noise then its blown fuse or shorted/loose wiper control wiring:-----
For complete troubleshooting i suggest you few helpful links with accurate solutions.
-------------
Click the link below:-------

1993 Ford F350 wipers not working?

http://repairhelpcenter.blogspot.in/2012/02/1993-ford-f350-wipers-not-working.html
------------ How to Replace a Windshield Wiper Motor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-windshield-wiper-motor.html

------------

Wipers not working, but hear relay click on Lincoln LS?

http://schematicsdiagram.blogspot.com/2011/12/wipers-not-workingbut-hear-relay-click.html

-----------

Car windshield wiper gets power for movement and stops?

http://schematicsdiagram.blogspot.com/2011/12/car-windshield-wiper-gets-power-for.html

----------

How does cars Windshield Wiper System Works

http://technoanswers.blogspot.com/2011/11/how-does-cars-windshield-wiper-system.html

---------

1997 Honda Protege: Replace Wiper Transmission?

http://technoanswers.blogspot.in/2012/06/1997-honda-protege-replace-wiper.html

----------------

Windshield wiper fluid container leaking?

http://whatisbyme.blogspot.in/2012/05/windshield-wiper-fluid-container.html

-----------------

Where is wiper fuse located on1993 chevrolet suburban

http://technoanswers.blogspot.in/2012/02/where-is-wiper-fuse-located-on1993.html

------------

2002 Toyota Sienna: Wipers and Passenger side Power window stopped working?

http://technoanswers.blogspot.in/2012/04/2002-toyota-sienna-wipers-and-passenger.html

-------------

Complete wiper components replacing details for Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/complete-wiper-components-replacing.html

------------
These details will help.
Thanks.

dis-connect wiper motor and replace fuse and try switching wiper motor on if fuse does not blow motor faulty and shorting out and causing fuse to blow.if still blows fuse must be a short in the wiring from wiper motor plug back to wiper motor switch.

wiper motor proberly faulty