I need to see a diagram for the coolant system for a 2004 ford Taurus, top and bottom

Here is the procedure: Remove radiator cap, Drain coolant, remove drain plug located at bottom of radiator. Remove upper and lower radiator hoses, Remove electric fans mounting 4 bolts and disconnect electrical plug connection, Remove Hi & Lo transmission cooler lines connected behind radiator and finally, remove upper radiator mounting bolts located on top and remove radiator upward.

Follow bottom radiator hose from the radiator to the engine block, thermostat is there, it takes a short 10 mm 3/8 drive socket to remove the bottom bolt, and a 10 mm wrench to remove the top bolt. Drain the radiator first in a clean bucket, so you can reuse the coolant, then take the breather hose off the fuel injection body, then once you have removed the two bolts off the goose neck, you may be able to pry it apart at the top between the two cast pieces, you will also need to remove the ground screw on the housing, and the radiator hose attached to it, make sure you put the thermostat in the same way you took it out, the thermostat goes between the gasket, take very little gasket compound and put it on the goose neck , this will help keep the thermostat in place when putting back together, be sure you have all the hoses hooked back up and its snug, also the hose going to the injection body, put your antifreeze back in the radiator first them fill the coolant jug just past max run the car till the radiator fan turns on then turn it off and let cool for a bit and repeat until you have all the air out of the system and the coolant jug it filled to max as it runs to operating temperature! you will have to buy an extra 2 gallons of prestone antifreeze, because you'll have lost some from taking the goose neck off the thermostat housing! Good Luck!

IF EVERYTHING WITH COOLANT SYSTEM SEEMS TO BE IN ORDER WITH NO LEAKS THEN IT SOUNDS LIKE THERMOSTAT MAY NEED REPLACED

you need to replace thermostat and radiator cap.look under hood around engine compartment.look for a radiator cap near radiator,add 50/50 antifreeze and water to coolant system to bring up boiling point.pure water will cause engine run hotter because water evaporate away,remove radiator pour coolant in the radiator until coolant stop dropping in the radiator now some vechicle pour coolant in the coolant overflow jug,pour coolant until coolant level stop dropping and the coolant level stay at cold full mark.start engie let idle few minutes, watch coolant level in radiator if coolant start dropping add more coolant, when coolant level stop dropping put radiator cap back on let engine idle until both top radaitor hose and bottom coolant hose get warm turn off engine wait until it get cool then take a large rag slightly open radiator just a litle at a time to keep from getting scaled.once radiator remove add more coolant if low,put radiator cap back on start the engine let it idle watch the temp gauge if temperature gauge going hot zone stop engine wait until cool then add more coolant,keep doing this until engine stop overheating going into hot zone and coolant level stop dropping,make the coolant overflow jug coolant level stay at full cold mark, dont let jug run empty if so air will get in the coolant system causing engine to overheat.

YOU NEED BLEED AIR OUT THE COOLING SYSTEM.WAIT TO ENGINE COOL DOWN.YOUR VECHICLE YOU HAVE TO POUR COOLANT IN THE COOLANT OVERFLOW JUG UNTIL COOLANT LEVEL STAY AT THE FULL COLD MARK.THEN START ENGINE LET IT IDLE A FEW MINUTES WATCH COOLANT IN THE OVERFLOW JUG WHEN IT DROPS ADD MORE COOLANT UNTIL COOLANT LEVEL STAY AT FULL COLD MARK.WHEN COOLANT LEVEL STOP DROPPING IN OVERFLOW JUG.SCREW RADIATOR CAP BACK ON OVERFLOW JUG WATCH ENGINE COOLANT TEMPERATURE GAUGE AS COOLANT TEMPERATURE START CLIMBING TURN OFF ENGINE LET IT SET A WHILE KEEP FROM GETTING SCALDED.TAKE LARGE RAG PLACE OVER COOLANT OVERFLOW JUG CAP SLOWLY OPEN RADIATOR CAP A LITTLE AT A TIME UNTIL PRESSURE RELEASE.REMOVE OVER FLOW JUG CAP.ADD MORE COOLANT UNTIL COOLANT LEVEL AT THE FUL COLD MARK ON THE OVERFLOW JUG.THEN SCREW CAP BACK ON THE OVERFLOW JUG.START ENGINE LET IT IDLE AGAIN WATCH ENGINE COOLANT TEMPERATURE GAUGE WHEN TEMPERATURE GAUGE START CLIMBING.TURN OFF ENGINE WAIT A WHILE.CHECK COOLANT LEVEL IN THE OVER FLOW JUG.DO THIS PROCEDURE UNTIL THE COOLANT LEVEL IN THE COOLANT OVERFLOW JUG STOP DROPPING AND STAY AT FULL COLD MARK,WHEN THE TOP RADIATOR HOSE GET HOT THERMOSTAT OPENING AIR IS OUT THE COOLANT SYSTEM. WHEN ENGINE COOLS DOWN.CHECK COOLANT OVERFLOW JUG COOLANT MUST BE IN THE COOLANT OVER FLOW JUG AT THE FULL COLD MARK WHEN ENGINE COLD. DONT .DONT OVERFILL COOLANT OVERFLOW JUG.KEEP COOLANT IN THE OVERFLOW JUG IF YOU LET COOLANT OVERFLOW JUG RUN DRY AIR WILL BE DRAW IN COOLANT SYSTEM CAUSE ENGINE TO OVERHEAT.

REPLACE THERMOSTAT IF TOP COOLANT COOLANT HOSE GOING TO RADIATOR IS HOT TO TOUCH THERMOSTAT OPEN. TO BLEED COOLANT SYSTEM FIRST YOU NEED TO ADD COOLANT TO THE COOLANT OVER FLOW JUG UNTIL COOLANT LEVEL STOP DROPPING AND STAY AT FULL COLD MARK.WAIT 3 MINUTES IF COOLANT DROPS ADD MORE COOLANT UNTIL COOLANT STAY AT FULL COLD MARK.WITH RADIATOR OVER CAP OFF CRANK ENGINE FOR MINUTE WATCH COOLANT LEVEL AT OVERFLOW JUG.IF COOLANT DROPS ADD MORE COOLANT IN THE OVERFLOW JUG.WHEN COOLANT LEVEL STOP DROPPING IN OVERFLOW JUG.SCREW BACK ON THE RADIATOR CAP TO OVERFLOW JUG.WHILE ENGINE IDLING WATCH TEMPERATURE GAUGE WHEN TEMPERATURE START CLIMBING TURN OFF ENGINE WAIT A WHILE KEEP FROM GETTING SCALDED.WHEN COOLANT COOL DOWN SOME. PLACE A LARGE RAG OVER THE COOLANT OVERFLOW JUG OPEN CAP LITTLE AT A TIME UNTIL PRESSURE RELEASED, THEN REMOVE CAP ADD MORE COOLANT IN THE OVERFLOW JUG TO THE FULL COLD MARK.THEN REPEAT THE PROCESS SCREW BACK ON THE COOLANT OVERFLOW RADIATOR PRESSURE CAP.THEN START ENGINE WATCH TEMPERATURE GAUGE WATCH COOLANT TEMPERATURE GAUGE WHEN COOLANT TEMPERATURE START RISING TURN OFF ENGINE AGAIN WAIT UNTIL ENGINE COOL DOWN ENOUGH TO KEEP FROM GETTING SCALDED TAKE PLACE LARGE RAG OVER RADIATOR CAP WHICH IS THE COOLANT OVERFLOW JUG CAP OPEN CAP LITTLE AT A TIME UNTIL PRESSURE RELEASED ADD COOLANT UNTIL AT FULL COLD MARK. WHEN YOUR COOLANT LEVEL STOP DROPPING.AND TOP RADIATOR HOSE VERY HOT THERMOSTAT OPEN AND AIR IS OUT THE COOLANT SYSTEM. MAKE SURE YOUR COOLANT OVERFLOW JUG HAS COOLANT IN IT,WHEN ENGINE COOL DOWN CHECK COOLANT OVERFLOW JUG KEEP COOLANT LEVEL AT FULL COLD MARK.BECAUSE IF OVERFLOW JUG IS EMPTY THATS A SIGN RADIATOR COOLANT LEVEL LOW.WHEN OVERFLOW JUG EMPTY IT WILL ALLOW AIR GET IN THE COOLANT SYSTEM AND CAUSE CAR TO OVERHEAT.WHEN REPLACING THERMOSTAT ALSO REPLACE THE RADIATOR CAP ON THE COOLANT OVERFLOW JUG.

CAR OVERHEATING FIRST CHECK FOR LOW COOLANT IN THE RADIATOR COOLANT OVERFLOW JUG.IF COOLANT LEVEL IN OVERFLOW JUG LOW REFILL ADD COOLANT BACK TO THE FULL COLD MARK.PUT RADAITOR CAP ON COOLANT OVERFLOW JUG START ENGINE LET IT IDLE UNTIL IT OPERATING TEMPERATURE.MAKE SURE TOP RADIATOR HOSE GETTING HOT WHILE ENGINE WARM UP.IF TOP RADIATOR HOSE DONT GET HOT WHILE ENGINE IDLING YOUR THERMOSTAT COULD BE STUCK CLOSE CAUSING CAR TO OVERHEAT.IF TOP HOSE IS GETTING HOT.CHECK FOR COOLANT LEAKS CHECK TOP RADIATOR HOSE AND BOTTOM RADIATOR HOSE FOR LEAKS.CHECK FOR LEAKS AT THE RADIATOR CORES AND PLASTIC SIDE CONTAINERS.IF ALL IS GOOD ENGINE OVERHEATING WHILE IN A LONG TRAFFIC LINE, COOLANT FANS NOT COMING ON.COULD HAVE FAULTY ENGINE COOLANT TEMPERATURE SENSOR OR BLOWN COOLING FAN FUSE OR RELAY.COULD HAVE PCM FAULT.MAKE COOLING FAN ELECTRICAL CONNECTORS AND WIRING NOT DAMAGE OR BROKEN.

The lower radiator hose is usually connected to the water pump. It's purpose is to draw coolant from the bottom of the radiator and circulate it through the engine and heater. a word of caution, even if you drain the radiator when you loosen the hose there will be a sizeable amount of coolant flowing from that point. Keep a pan handy!!!

The reservoir is the traditional top tank of your radiator.

The answer to your question is yes.

Remove the lower radiator hose from the radiator.