I'm not an expert on the Aura, but most Saturn engines have the knock sensor on the back of the engine near the firewall. It'll be almost right in the middle.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
JustAnswerhttps://www.justanswer.com > Ford Repair
Mar 15, 2020 - Ok give me a minute to look it up. It is under the lower intake manifold. You have to remove that to replace the knock sensor. The block, you ...
Fixyahttps://www.fixya.com > Forum > Cars & Trucks
4 hours ago - Locate the knock sensor, which is located near the rear of the engine block, under the intake manifold. Disconnect the electrical connector from ...
The knock sensor on a 2003 Honda CRV is located on the engine block. Specifically, it is located under the intake manifold, which means it can be difficult to access. Here are the steps to locate and replace the knock sensor on a 2003 Honda CRV:
Disconnect the negative battery cable to prevent electrical shock.
Remove the intake manifold. This involves removing several bolts and electrical connections.
Locate the knock sensor, which is located near the rear of the engine block, under the intake manifold.
Disconnect the electrical connector from the sensor.
Remove the sensor from the engine block. This may require a special tool, depending on the specific design of the sensor.
Install the new knock sensor, making sure it is properly aligned and tightened to the correct torque specification.
Reconnect the electrical connector to the sensor.
Reinstall the intake manifold, making sure all bolts and electrical connections are properly secured.
Reconnect the negative battery cable.
Note that if you are not experienced with working on engines or are unsure of how to proceed, it may be best to seek the assistance of a qualified mechanic to replace the knock sensor on your 2003 Honda CRV.
Nathan, 2 Knock's are located under intake manifold.
Check the attached links,
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
? 6:41
https://www.youtube.com/watch?v=yacSiSJ5Vc0
Feb 17, 2014 - Uploaded by Cody the Car Guy
do you know where is the knock sensor on a 2005 Honda accord coupe .... 2001-2005 Honda Civic Cam ...
Turn ignition off. Disconnect knock sensor 3 - pin harness connector. Locate knock sensor, on cyli nder block. On Optima 2.7L engine, sensors are located on both sides of cylinder block. . Remove knock sensor from cylinder block. To install, reverse rem oval procedure.
Your knock sensor is located Under the hood, center, front engine area, below intake
manifold, mounted on block.
A defective knock sensor may cause engine detonation or reduced
spark advance and fuel economy. When a knock sensor is removed and
replaced, the sensor must be tightened to its specified torque. If the
knock sensor is installed tighter than it should be, it may become too
sensitive and provide an excessively high voltage signal, resulting in
more spark ****** than required. When the knock sensor is installed
looser than it should be, the knock sensor signal will be lower than
normal, resulting in engine detonation.
Knock Sensor Description
addthis_pub = 'car-suff';
A quality Knock Sensor is more important than ever thanks to today’s increasing gas prices. Your Engine Knock Sensor enables your vehicle to obtain the optimum combination of timing and fuel/air mixture to generate power and efficiency and that means less wasted gas. Our guaranteed low prices make us your one-stop Knock Sensor Location. Regardless of the brand, make or model car, truck, van or SUV you drive, we make it easy to locate the application specific Knock Sensor that’s perfect for your vehicle. Our state of the art parts locating system puts you just a few mouse clicks away from the Knock Sensor you need and at a price you cannot beat anywhere. Click. Click. Click. And you are there. In addition to robbing you of fuel economy and performance a faulty Knock Sensor can cause expensive damage to your engine. Remember, the Knock Sensor keeps fuel from detonating in the cylinder … exploding rather than quickly burning as it should. If not replaced a faulty Knock Sensor can quite literally cause hundreds if not thousands of dollars in damage. There is really no need to look any further to find the Knock Sensor that’s application specific for your car, truck, van or SUV – high performance or family vehicle. We’ve got guaranteed low prices and shipping that other suppliers envy. Give us a try, we think you’ll be happy … in fact we guarantee it.
×