How to remove th body control unit on this car ?

Question edited for clarity and spelling of 'module'.
Question moved to model category.
No reason given for wanting to know where it is.

What's the ram 1500 bcm location?

Vehicle History https://www.vehiclehistory.com > questions > whats-th...
6 answers
For the 2015 Ram 1500, the BCM (body control module) can be found on the driver's side of the car. It is located in the fuse box. If for any reason the BCM .

More here

https://www.ramforumz.com/threads/body-control-module.277957/

https://www.youtube.com/watch?v=RcjBUdL1ZoA

If you remove any Control Module it will need programming. The Body Control Module (BCM) controls your immobiliser system so a replacement unit won't recognise the key or the vehicle and the security system will 'trip' to stop the car starting. I would suggest you pay a specialist to do this because if you get it wrong it'll cause a lot more (probably expensive) problems.

Sounds like yes, just match the pin configuration on both modules. If the are the same .........try it

Mmmmm.... start here:
2005 saturn vue bcm reprogram Google Search

and this:
http://www.saturnfans.com/forums/showthread.php?t=195610

See this:
2004 saturn bad body control module

then here:
Saturn BCM body control module Removal

Try these YOUTUBES... NOT the same year:
2004 saturn bad body control module

2002 Saturn Veu BCM issue and quick fix
(this MAY help you)?

Anthony

muffler explosion
is caused by 2 things
air entering the exhaust (leaks )
and gross engine fuel controls out of control, a very rich conditon
there is no person on earth can guess why.
a tech, would do about 10 tests, and find the cause, then the part.
87 is a water shed year.
is your car CARB or EFI. some were CARB. so what engine size
and which fuel system. ?????

is this your car engine, (wild guess) USA cars only not export Jeeps.

The throttle body fuel injection is used on 1987-90 Wranglers equipped with the 2.5L engine and is a "pulse time'' system that uses a single solenoid-type injector to meter fuel into the throttle body above the throttle plate. Fuel is metered to the engine by an Electronic Control Unit (ECU),

you said you tried applying direct voltage to the pump? proceed to remove the fuel tank and check the harness inside for continuity, both wires going to the pump itself. If wires prove to be ok , then proceed to replace pump .

U will have to open th door from th in side. To unlock it. Remove the inside panel. And where th key go, u can unlocked from th inside. But firs try to lock and unlock th door whit th electric control while u try to open th door. Because sometimes they are just stock and need lubrication. Good lock

If you are talking about just replacing the electronic ABS module (EBCM), it simply unplugs and unscrews from the hydraulic control unit. If you are talking about replacing the hydraulic control unit (HCU) then you must disconnect the EBCM. Disconnect all of the brake lines from the HCU. Remove the mounting bolts from the HCU and remove HCU from vehicle. Then you reverse th order to reinstall. Once it is installed you must use a scan tool to perform automated bleeding to get all the air out of the hydraulic unit and the rest of the brake system.

CALL YOUR DEALER AND SEE IF YOU FALL IN THE RECALL SOME OF THERE YEAR SEDONAS HAD RECALL FOR THROTTLE CABLES . IF YOUR NOT IN TH CAT. THEN YOU POP THE CLIP AT THE TOP OF THE ACCEL. PEDAL AND REMOVE AIR INTAKE HOSE WHICH WILL GIVE YOU EASIER ACCESS POP THE CLIP LOOSE TH THROTTLE BODY BRACKET AND REMOVE CABLE AND PULL THROUGH THE FIREWALL GOOD LUCK

the idle valve is mounted to the throttle body with a few screws.unplug the harness and remove screws carefully they tend to break. you might have to remove the throttle body to get to it. there are water lines going to the throttle body so be sure to clamp them off before removing them, and make sure the engine is cold, hot anifreeze burns bad.