When starting wipers came on and stay on no matter of position of control, washer fluid over head dome light won't turn on, rear washer and whiper won't work.

Rear Wiper/Washer System Components
The rear wiper/washer system consists of the following components:
• Rear wiper/washer switch
• Window wiper module-rear
• Window washer pump-rear
• RR WIPER 15A fuse
• RR WPRB 25A fuse
Rear Wiper/Washer System Operation
The rear wiper module controls rear wiper motor operation. Battery voltage supplied to the module is used to operate the wiper motor in all modes and to return the rear wiper arm to the park position after the ignition is turned off. Accessory voltage supplied to the rear wiper/washer switch is used to supply the rear window wiper and washer switch signal circuits. In wiper switch positions 1 and 2 the wiper switch signal circuit voltage level to the wiper motor module determines the wiper motor delay interval. The rear window washer pump supply voltage circuit is used to provide the operating voltage for the rear washer pump for as long as the rear washer switch is pressed. The rear window washer switch signal circuit is used as a wash signal to the rear wiper motor module to operate the wipers during the rear wash operation.


Did you replace the rear wiper module ?

Did you check fuse's & relays ?
Rear Window Wiper Operation
The rear wiper motor is controlled by the SJB. The SJB supplies power to the rear wiper motor from the integrated rear wiper relay. The SJB will activate the relay when all of the following conditions are met:

• Ignition switch is in the ON position
• Liftgate glass and liftgate are closed
• Multi-function switch is in the ON or intermittent position

The SJB also supplies voltage to the rear wiper motor from SJB fuse 21 (15A) when the ignition switch is in the ON position. This power feed is used to continue the wipe cycle when the multi-function switch is turned to the OFF position. The SJB receives inputs from the multi-function switch that applies ground to the low speed wipe input or applies ground to the intermittent wipe input. When either of these circuits are grounded, the SJB activates the integrated rear wiper relay and power is supplied to the rear wiper motor to move the rear wiper motor from the park position. An internal switch in the rear wiper motor then moves to the run position which connects the accessory relay power to the rear wiper motor. When the rear wiper motor returns to the park position, the internal switch in the rear wiper motor moves back to the park position. If the multi-function switch is in the ON position, the rear wiper relay is still activated, power is supplied to the rear wiper motor, and the wipe cycle starts again. If the multi-function switch is in the intermittent position, the rear wiper relay does not activate until the predetermined dwell time has elapsed, at which time the SJB activates the rear wiper relay and the wipe cycle starts again. The SJB is the smart junction box .(computer )

Rear Washer System
The SJB supplies power to the rear washer pump from fuse 21 (15A) when the ignition switch is in the ON or ACC position. The rear washer pump receives ground from the multi-function switch when the wash function is turned ON. The multi-function switch also signals the SJB when the rear wash is activated and the SJB then activates the rear wiper.

Replacing parts just to replace them wont fix a bad wire or part. Better to use a voltmeter and ohn meter to check if your getting power to the wires. You may have a bad connection or bad switch on the column for the pumps. Without checking the circuits it will behard to tell what it is thats wrong. Find a wiring diagram and trace the wires and components.

Did you check the fuse ? Do you hear the wiper motor running ? If the fuse is good you would need to test the electrical circuit for the wiper motor ,viewing a wiring diagram an then use a DVOM - digital volt ohmmeter to test
What body type is it ? Vin 6 or 3 could have a circuit breaker for power supply or fuse ,both are located in the rear fuse block .

Rear Wiper/Washer System Components
The rear wiper/washer system consists of the following components:
• Rear window wiper motor
• Rear window washer fluid pump
• Rear wash relay
• Rear window wiper/washer switch
• RR wiper 15A circuit breaker
• WASH 20A fuse
Rear Wiper/Washer System Controls
• Body control module (BCM)
• Liftgate control module (LGM)
• Rear wiper/washer switch

Here is how it is controlled

Rear Wiper/Washer System Operation
The rear window wiper/washer switch is an input to the BCM. The requested rear wiper mode is sent to the liftgate control module (LGM) by the BCM as a message on the serial data circuit, and the rear window wiper motor is controlled by the LGM. The switch power circuit to the rear wiper/washer switch is a 12-volt reference supplied by the BCM during ignition on, accessory or RAP power modes. The rear wiper/washer switch is a series of resistors and the switch position is determined by the voltage of the rear wiper/washer switch signal circuit to the BCM. The rear wiper/washer switch has continuity at all times and the BCM expects a rear wiper/washer switch signal voltage in all switch positions including OFF. The rear wiper motor is supplied battery positive voltage and ground. The LGM controls rear wiper motor operation through the rear wiper motor control circuit. The rear wiper motor control circuit is supplied a battery positive reference voltage by the rear wiper motor module and is pulse width modulated to ground by the LGM. The duty cycle of the pulse width modulation determines the rear wiper motor operating mode. The liftglass and liftgate ajar switches are inputs to the LGM and must be in an inactive state in order for rear wiper washer system operation to be enabled. When an ajar switch is active the LGM suspends wiper motor operation directly and sends the ajar switch status messages over the serial data circuit enabling the BCM to suspend washer pump operation. The rear window washer pump is controlled by the BCM through the rear washer relay. Battery positive voltage is supplied to the coil and switch sides of the rear washer relay. When the rear window wash request is active the BCM energizes the relay by grounding the relay coil through the rear washer relay control circuit. When the relay is energized battery positive voltage to the relay switch is supplied to the washer pump control circuit.

Your best bet mite be to have a qualified repair shop check for codes in the BCM or LGM
--------------------------------------------------------------------------------
DTC B1017 or B3970

The rear wiper motor is supplied battery positive voltage and ground. The liftgate control module controls rear wiper motor operation through the rear wiper motor control circuit. The rear wiper motor control circuit is supplied a battery positive reference voltage by the rear wiper motor module and is pulse width modulated to ground by the liftgate control module. The duty cycle of the pulse width modulation determines the rear wiper motor operating mode.

There are something's involved that you are not aware of , or familiar with . Electronic control modules .
Rear Wiper/Washer System Controls
• Body control module (BCM)
• Liftgate control module (LGM)
• Rear wiper/washer switch
Do you know what a serial data network is ?
Rear Wiper/Washer System Operation
The rear window wiper/washer switch is an input to the BCM. The requested rear wiper mode is sent to the liftgate control module (LGM) by the BCM as a message on the serial data circuit, and the rear window wiper motor is controlled by the LGM. The switch power circuit to the rear wiper/washer switch is a 12-volt reference supplied by the BCM during ignition on, accessory or RAP power modes. The rear wiper/washer switch is a series of resistors and the switch position is determined by the voltage of the rear wiper/washer switch signal circuit to the BCM. The rear wiper/washer switch has continuity at all times and the BCM expects a rear wiper/washer switch signal voltage in all switch positions including OFF. The rear wiper motor is supplied battery positive voltage and ground. The LGM controls rear wiper motor operation through the rear wiper motor control circuit. The rear wiper motor control circuit is supplied a battery positive reference voltage by the rear wiper motor module and is pulse width modulated to ground by the LGM. The duty cycle of the pulse width modulation determines the rear wiper motor operating mode. The liftglass and liftgate ajar switches are inputs to the LGM and must be in an inactive state in order for rear wiper washer system operation to be enabled. When an ajar switch is active the LGM suspends wiper motor operation directly and sends the ajar switch status messages over the serial data circuit enabling the BCM to suspend washer pump operation. The rear window washer pump is controlled by the BCM through the rear washer relay. Battery positive voltage is supplied to the coil and switch sides of the rear washer relay. When the rear window wash request is active the BCM energizes the relay by grounding the relay coil through the rear washer relay control circuit. When the relay is energized battery positive voltage to the relay switch is supplied to the washer pump control circuit.

Your best bet , take it to a qualified repair shop and have it checked for DTC'S - diagnostic trouble codes .
DTC B1017 or B3970
The rear wiper motor is supplied battery positive voltage and ground. The liftgate control module controls rear wiper motor operation through the rear wiper motor control circuit. The rear wiper motor control circuit is supplied a battery positive reference voltage by the rear wiper motor module and is pulse width modulated to ground by the liftgate control module. The duty cycle of the pulse width modulation determines the rear wiper motor operating mode.
DTC B3799

2
Turn the ignition ON.
Operate the rear wiper switch through all the switch positions.
Does the rear window wiper operate normally?
--
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Install a scan tool.
Display the liftgate control module data list.
Observe the following parameters while operating the respective switches. Refer to Scan Tool Data List for typical values.
• Liftgate Ajar Switch
• Liftglass Ajar Switch
Did the scan tool indicate the correct switch positions?
--
Go to Step 4
Go to Courtesy Lamps Inoperative in Lighting Systems
4
Observe the requested rear wiper parameter in LGM data list.
Operate the rear wiper switch through all the switch positions.
Does the scan tool indicate the correct requested rear wiper parameter in relation to the switch position?
--
Go to Step 5
Go to Step 6

There is a electric motor that pumps washer fluid . Located in the bottom of the washer fluid tank .
Wash Operation (Front and Rear Wipers)
The front and rear washer systems use the same windshield washer fluid pump. When either the front or rear wiper is in the washer position voltage will be supplied to one side of the windshield washer fluid pump (depending on whether it is front or rear), while the other side of the pump is grounded.
At this point, the windshield washer fluid pump sprays solvent onto the windshield. When the front or rear washer is activated, the BCM receives an input from the switch that is activated. The BCM will control the wipers while in the WASH mode. The BCM will control either the front wiper relay or the rear wiper relay to turn on the wipers. The windshield wipers operate at low speed for 3 swipes and returns to the park position.

When turning on the washers do you hear the motor run ? Have some one try it while you listen at the washer fluid tank ! These pump motors do go bad .
turn OFF the ignition.
Disconnect the harness electrical connector of the windshield washer fluid pump.
Connect a test lamp from the windshield washer pump control circuit to a good ground .
Turn ON the ignition, with the engine OFF.
Press the front washer switch.
Does the test lamp illuminate?
YES or NO !

check battery, also alternator

Here are some more common problems.

• Motor:

The wiper motor is commonly replaced and was often not the problem. Don't replace the motor yet. maybe it's not the motor. It could be a fuse or something at the wiper switch. The wiper motor has two windings, fast and slow. The wiper switch sends a ground signal to each motor winding. More often, there are problems with the relay, or at the wiper switch, or in the cable to the motor.

• Windshield Washer:

Don't be too quick to replace the washer pump. The problem is often just a clog in the sprayer heads. You can clean out the sprayer holes with a needle, some have two holes, so look closely. Hope this helps.

Find under the hood botle/container with cap like this

There is only one container for washer fluid, and for front and rear whiper fluid goes from ths same container witch is under the hood.
If your front washer is working and rear doesnt than it's problem with fluid pump or line from the containet to the rear wiper is damaged or disconected.

what is P13K?

check the fuse first. dealer can hook up NGS Tester and get fault codes to see what is wrong.

Principles of Operation
NOTE: The generic electronic module (GEM) will not activate the rear wiper system if either the liftgate or the liftgate glass is ajar. If either the liftgate or the liftgate glass becomes ajar while the rear wiper is in operation, the GEM will park the rear wiper motor.
There are two distinct modes of wiper operation:

• Off Mode: In this mode, there is no rear wiper activity, and the wiper motor will be in the PARK position.
• Interval Mode: This mode is selected when the rear wiper switch is in either the Interval 1 or 2 position. When this mode is selected, the rear wiper motor is driven up onto the glass by activating the rear wiper UP relay. When the wiper motor HIGH/LOW/PARK position input reaches the high position, the UP relay is deactivated and the DOWN relay is activated to reverse the wiper motor direction. When the wiper motor reaches the LOW position, as determined by the HIGH/LOW/PARK position input, the GEM deactivates the DOWN relay and will begin a new wiper cycle 1 to 10 seconds later, depending on the interval position selected.

To engage the rear window washer, rotate the rear window washer selector downward to the WASH position. The rear window wiper will run as long as the WASH position is selected. When the rear window washer selector returns to the OFF, INT 1 or INT 2 position, the washer will stop immediately, but the rear window wiper will continue for two to three sweeps and then return to its previous mode of operation.
The low washer fluid indicator chime warns that the washer fluid level is low. The low washer fluid indicator chime is a single tone with a duration of one second. The chime will sound when the low washer fluid indicator is initially activated.
The low washer fluid indicator warns that the fluid level in the washer reservoir is low. The low washer fluid indicator will illuminate when the washer fluid level is low and the ignition switch is in the RUN position.
The low washer fluid indicator will deactivate when the washer fluid reservoir is filled and the ignition switch has been cycled from RUN to OFF, then to RUN.
Inspection and Verification

1. The wiper/washer system is a generic electronic module (GEM) controlled system; refer to Section 419-10 .

1. Verify the customer concern by operating the wiper/washer system.

1. Visually inspect for obvious signs of mechanical and electrical damage.

Visual Inspection Chart Mechanical Electrical

• Hoses to windshield washer pump
• Wiper linkage

• Fuses 6 (5A), 8 (5A), 15 (5A), and 20 (5A)
• Wiring harness
• Loose or corroded connector(s)
• Relays
• Motors
• Multifunction switch
• Washer fluid level switch

----------------------------------------

• The wipers are inoperative — rear

• Fuses 6 (5A), 8 (5A), 15 (5A), and 20 (5A).
• Circuitry.
• GEM.
• Multifunction switch (wiper/washer switch).
• Rear wiper up relay.
• Rear wiper down relay.
• Rear wiper motor.