Question about 2007 Hyundai Getz 1.4

1 Answer

WHY IS MY ABS LIGHT ON?

LIGHT ON SINCE CAR BACK FROM PANELBEATER.CAR HAD BODY PANNELS REPLACED.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 2 Answers

The sensor that indicates the car that the ABS os blown out is broken. The ABS itself probably has no problem, you need to replace the sensor that tells the car if the ABS has been used or not. But you may also just visit a mechanic and he will replace it for you.

Posted on Nov 30, 2015

Ad

1 Suggested Answer

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My abs light don't come on my ford 2003


abs light on dash panel should only light for two seconds upon starting of engine , then go out . if it comes on and stays on then this indicates a fault has been detected in your abs system , by body control module (fault can be any where on car) a code reader will be required to know reason for abs fault

Jun 24, 2015 | Ford Cars & Trucks

3 Answers

My ABS/Brake light is on.Why is that?


Hi Barbara this light lets you know there is a fault in the ABS system. You will need a garage to plug it in to diagnose exactly what's wrong. Regards Jim...

May 12, 2015 | Cars & Trucks

1 Answer

I have three warning light lit up on my dash ABS, Service engine, trac off but when you plug in a diagnostic tool there is no codes or reading. You can clear them out and they are gone for a short while...


check abs, trac off can be turned off by computer service engine light can come on for both them items. check for air in ABS system, look for bleeder on ABS valve body

Sep 19, 2017 | 2002 Chevrolet Cavalier Coupe

1 Answer

My VSC, VSC off and ABS light came on after I had m tie rods changed. I took it to get a diagnostic and they said the speed sensor was back on the right side. After I got the car back the car...


The ABS system measures wheel speed on each wheel. If one wheel is "seen" by the body computer as turning faster than the other 3 the ABS will apply brake pressure to that wheel to prevent a skid or spin.
Vehicle Stability Control uses the same equipment.
Interesting that your ABS was working before the repairs.

Jun 25, 2012 | 2005 Lexus Gs 300

1 Answer

I HAVE JUST PURCHASED Toyota Yaris 1.0l reg FE52 ACV. Question;- does the car have ABS


a easy way to tell for sure is to turn ur steering wheel to the left ur left front wheel will be pointing out, look between the tire and the inner fender well.dont forget a light. u will see a black rubber hose from the body of the car to the brake caliper it is about 1 foot long an around a half inch thick..this is the brake hose..now if u have abs there will also be a thin black wire from the body of the car connected almost in the center of the part where the brake hose is connected this is ur abs electrical wire...some people will tell u to turn the car to the run position( when all the lights r on on the dash board) but if ur abs light is burnt out u wont know for sure

Jul 16, 2011 | Toyota Yaris Cars & Trucks

1 Answer

BCM does not communicate with code reader.


Check that ALL body grounds are clean and tight. A faulty ground can cause these problems in any vehicle.

Aug 25, 2017 | 1996 Chevrolet Cavalier

3 Answers

Both abs and traction control light stays on also spedo not working have checked all related fuses all ok have tried to scan with both snapon solus and launch x431 niether will communicate with abs ecu but...


had my 2000 chev impala 3.8 liter ,traction control llight and abs light both go on the reset it and go right back on .so i replaced both sides of the bearing hub assembly this is connected the senser,so far so good.replaced it dec 21 2009 about 3 hours ago. because the assembly came appart when took off.

Oct 30, 2009 | 1997 Acura CL

1 Answer

Gauges go out, car runs fine, radio works, abs light on turn signal works


this is a body control module (BCM) fault, replace it..

May 30, 2009 | 1997 Dodge Caravan

1 Answer

Excessive current to body computer


I had a voltage regualtor sticking in an alternator once that done the same thing. The alt worked fine but the reg would stick causing a dead battery try unplugging the alt. when the car is idle and see if the problem goes away

Apr 05, 2009 | 2001 Chevrolet Malibu

Not finding what you are looking for?
2007 Hyundai Getz 1.4 Logo

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...