SE. How do I remove transmission oil cooler line?

RADIATOR
Removal
1. Disconnect battery ground cable.
2. Drain engine cooling system as described.
3. Remove engine air cleaner.
4. Remove upper radiator hose from water bypass tube.
5. Remove radiator overflow hose from radiator and fan shroud.
6. Remove transmission oil cooler line from oil cooler inlet fitting.
7. Remove nuts retaining A/C condenser core to the radiator.
8. Disconnect engine control sensor wiring from the auxiliary electric cooling fan motors and the CCRM.
9. Raise vehicle on hoist.
10. Remove splash shield from lower radiator support and front sub-frame.
11. Remove lower radiator hose from radiator.
12. Remove oil transmission cooler line from oil cooler outlet fitting on radiator.
13. Remove retaining screws for power steering/transaxle oil cooler and position cooler aside.
14. Support fan shroud, radiator and A/C condenser core with a suitable jackstand. Remove lower radiator
support.
15. Position jackstand aside and carefully remove radiator and fan shroud.
16. Remove two retaining bolts for fan shroud at top of radiator and remove fan shroud from radiator.
17. Remove upper radiator hose from radiator.
NOTE: Loosen transmission oil cooler lines while securely holding radiator
connector with a back-up wrench.
NOTE: Loosen transmission oil cooler lines while securely holding radiator
connector with a back-up wrench.
18. Remove the radiator.

RADIATOR
Removal
1. Disconnect battery ground cable.
2. Drain engine cooling system as described.
3. Remove engine air cleaner.
4. Remove upper radiator hose from water bypass tube.
5. Remove radiator overflow hose from radiator and fan shroud.
6. Remove transmission oil cooler line from oil cooler inlet fitting.
7. Remove nuts retaining A/C condenser core to the radiator.
8. Disconnect engine control sensor wiring from the auxiliary electric cooling fan motors and the CCRM.
9. Raise vehicle on hoist.
10. Remove splash shield from lower radiator support and front sub-frame.
11. Remove lower radiator hose from radiator.
12. Remove oil transmission cooler line from oil cooler outlet fitting on radiator.
13. Remove retaining screws for power steering/transaxle oil cooler and position cooler aside.
14. Support fan shroud, radiator and A/C condenser core with a suitable jackstand. Remove lower radiator
support.
15. Position jackstand aside and carefully remove radiator and fan shroud.
16. Remove two retaining bolts for fan shroud at top of radiator and remove fan shroud from radiator.
17. Remove upper radiator hose from radiator.
NOTE: Loosen transmission oil cooler lines while securely holding radiator
connector with a back-up wrench.
NOTE: Loosen transmission oil cooler lines while securely holding radiator
connector with a back-up wrench.
18. Remove Radiator

No,

Section 03-03: Engine Cooling 1997 Taurus, Sable Workshop Manual
REMOVAL AND INSTALLATION Radiator Aluminum Core, Crossflow
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fuel Line Disconnect Tool Set T90T-9550-S
Removal
CAUTION: Do not mix Standard (green) Coolant with Extended Life Coolant (orange). If mixing occurs, drain engine cooling system and refill with originally equipped coolant type. If this contamination occurs, the service interval of Extended Life Coolant will be reduced from 6 years/150,000 miles to 3 years/30,000 miles.

1. Disconnect battery ground cable (14301).
   

1. Remove battery (10653) as described in Section 14-01 .
   

1. Remove clip retaining contant control relay module and position module aside.
   

1. Remove battery tray (10732) as described in Section 14-01 .
   

1. Remove radiator cap (8100).
   

1. Raise vehicle on hoist as described in Section 00-02 .
   

1. Remove radiator splash shield.
   

1. Drain engine cooling system as described in this section.
   

1. Remove the radiator mounting bracket assembly.
   

1. Remove lower radiator hose (8286).
   

1. Partially lower vehicle.
   

1. Remove upper radiator hose (8260).
   

1. Remove radiator overflow hose (8075).
   

1. Remove upper A/C condenser core retaining bolts.
   

1. Remove upper transmission oil cooler tube clips.
   

1. Remove lower transmission oil cooler tube (7C410)(EPN=7C410)using 3/8 Inch Fuel Line Disconnect Tool T90T-9550-C.
   

1. Raise vehicle on hoist.
   

1. Remove lower transmission oil cooler tube clips.
   

1. Remove lower transmission oil cooler tube (7C410)(EPN=7C410)using 3/8 Inch Fuel Line Disconnect Tool T90T-9550-C.
   

1. Remove transmission oil cooler bracket and position transmission oil cooler aside.
   

1. Remove lower A/C condenser core bolts and position A/C condenser core (19712)aside.
   

1. Remove radiator support bracket.
   

1. Remove radiator (8005).
   

Removal & Installation 4L60E/4L65E To Remove:

1. Remove or disconnect the following:
   • Transmission fluid
   • Transmission oil level indicator tube and seal from the transmission
   • Plug the oil level indicator tube opening in the transmission.
   • Remove or disconnect the following:
   • Shift cable end from the transmission shift lever ball stud
   • If equipped with a transfer case, remove the front propeller shaft.
   • Rear propeller shaft.
2. Plug the transmission oil cooler line connectors in the transmission case.
3. Remove or disconnect the following:
   • Starter motor.
   • Transfer case, if equipped.
4. Support the transmission with a transmission jack.
5. Remove the transmission mount nuts.
6. Remove the transmission crossmember.
7. Remove or disconnect the following:
   • Torque converter access plug 4L60E/4L65E removal
     
     
   • Flywheel to torque converter bolts
   • The two bolts securing the transmission rear mount to the transmission
   • The transmission vent hose, fuel lines, and the wiring harness from the transmission
   • The stud and the bolt securing the transmission to the engine
   • The six studs and one bolt securing the transmission to the engine. Install tool J21366 onto the transmission bell housing to retain the torque converter. Pull the transmission straight back.
   • The transmission from the vehicle
8. Flush the transmission oil cooler and cooling lines when you remove the transmission.

To Install:

1. Install or connect the following:
   • Tool J21366 onto the transmission bell housing to retain the torque converter.
   • Support the transmission with a transmission jack.
2. Raise the transmission into place and remove the tool from the transmission.
3. Slide the transmission straight onto the locating pins while lining up the marks on the flywheel and the torque converter. The torque converter must be flush onto the flywheel and rotate freely by hand.
4. Install or connect the following:
   • Six studs and one bolt securing the transmission to the engine. Tighten the studs and the bolt to 50 Nm (37 ft. lbs.).
   • Stud and bolt securing the transmission to the engine. Tighten the stud and the bolt to 50 Nm (37 ft. lbs.).
   • Flywheel to torque converter bolts. Tighten the stud and the bolt to 46 Nm (63 ft. lbs.).
   • Torque converter access plug.
   • Transmission vent hose, fuel lines, and the wiring harness to the transmission.
   • Two bolts securing the heat shield to the transmission. Tighten the bolt to 17 Nm (13 ft. lbs.).
   • Two bolts securing the transmission rear mount to the transmission. Tighten the bolts to 18 ft. lbs. (25 Nm).
   • Install the transmission crossmember. Tighten the nuts and bolts to 70 ft. lbs. (95 Nm).
5. Remove the transmission jack from the transmission.
6. Unplug the transmission oil cooler line connectors in the transmission case.
7. Install or connect the following:
   • Starter
   • Transmission oil cooler lines to the transmission
   • If equipped with a transfer case, install the front propeller shaft.
   • The rear propeller shaft
   • The shift cable end to the transmission shift lever ball stud
8. Unplug the oil level indicator tube opening in the transmission.
9. Install the transmission oil level indicator tube and seal to the transmission.
10. Tighten the oil pan bolts and fill the transmission with transmission fluid.
11. Lower the vehicle.

4L80E/4L85E To Remove:

1. Remove or disconnect the following:
   • Transmission fluid
   • Transmission oil level indicator tube and seal from the transmission
2. Plug the oil level indicator tube opening in the transmission.
3. Remove or disconnect the following:
   • Shift cable from the transmission shift lever ball stud
   • If 4WD vehicle, remove the propeller shaft.
   • If RWD vehicle, remove the propeller shaft.
   • The transmission oil cooler lines from the transmission
4. Plug the transmission oil cooler line connectors in the transmission case.
5. Remove or disconnect the following:
   • Starter motor
6. Support the transmission with a transmission jack.
7. Remove or disconnect the following:
   • The two bolts securing the heat shield to the transmission
   • The transmission vent hose, fuel lines, and the wiring harness from the transmission
   • One nut and one bolt securing the transmission brace to the engine bracket and transmission
   • The two bolts securing the torque converter cover to the engine
   • The four bolts securing the torque converter cover to the transmission
   • The six flywheel to torque converter bolts
   • The two bolts and nut securing the transmission rear mount to the transmission
   • The stud and the bolt on the right side securing the transmission to the engine
   • The remaining six studs and the one bolt securing the transmission to the engine
   • Tool J21366 onto the transmission bell housing to retain the torque converter
   4L80E/4L85E removal
   
   
8. Pull the transmission straight back. Remove the transmission from the vehicle.
9. Flush the transmission oil cooler and cooling lines when you remove the transmission.

To Install:

1. Install or connect the following:
   • Tool J21366 onto the transmission bell housing to retain the torque converter
2. Support the transmission with a transmission jack.
3. Raise the transmission into place and remove the tool from the transmission.
4. Slide the transmission straight onto the locating pins while lining up the marks on the flywheel and the torque converter. The torque converter must be flush onto the flywheel and rotate freely by hand.
5. Install or connect the following:
   • Six studs and one bolt securing the transmission to the engine. Tighten the studs and the bolt to 50 Nm (37 ft. lbs.).
   • The stud and bolt on the right side securing the transmission to the engine. Tighten the stud and the bolt to 50 Nm (37 ft. lbs.).
   • Six flywheel to torque converter bolts. Tighten the bolts to 60 Nm (44 ft. lbs.).
   • The two bolts securing the torque converter cover to the engine. Tighten the bolt to 50 Nm (37 ft. lbs.).
   • The four bolts securing the torque converter cover to the transmission. Tighten the stud and the bolt to 33 Nm (24 ft. lbs.).
   • The transmission vent hose, fuel lines, and the wiring harness to the transmission.
   • The two bolts securing the heat shield to the transmission. Tighten the bolt to 17 Nm (13 ft. lbs.).
   • The two bolts and nut securing the transmission rear mount to the transmission. Tighten the bolts and nut to 25 Nm (18 ft. lbs.).
   • The flywheel to torque converter bolts.
   • One nut and one bolt securing the transmission brace to the engine bracket and transmission. Tighten the bolts and nut to 50 Nm (37 ft. lbs.).
6. Remove the transmission jack from the transmission.
7. Install or connect the following:
   • Starter motor
8. Unplug the transmission oil cooler line connectors in the transmission case.
9. Connect the transmission oil cooler lines to the transmission.
10. Install or connect the following:
    • The transfer case
    • The rear propeller shaft
    • The shift cable end to the transmission shift lever ball stud
11. Unplug the oil level indicator tube opening in the transmission.
12. Install the transmission oil level indicator tube and seal to the transmission.
13. Tighten the oil pan bolts and fill the transmission with transmission fluid.
14. Lower the vehicle.

Removal & Installation 4.2L Engine To Remove:

1. Disconnect the negative battery cable from the battery.
2. Disconnect the brake booster hoses from the engine. Starter
   
   
3. Remove the positive battery cable and s-terminal lead from the starter.
4. Remove the starter from the engine.

To Install:

1. Install the starter to the engine. Tighten the nut and bolt to 37 ft-lb (50 Nm).
2. Install the positive battery cable and s-terminal to the starter. Tighten the battery cable nut to 80 in-lb (9 Nm). Tighten the s-terminal nut to 20 in-lb (2.3 Nm).
3. Connect the vacuum brake booster hose to the engine.
4. Connect the negative battery cable to the battery.

5.3L & 6.0L Engines To Remove:

1. Disconnect the negative battery cable from the battery.
2. Raise and support the vehicle.
3. Remove the rear steering gear crossmember from the frame. Starter
   
   
4. Detach the wire harness from the transmission oil cooler line bracket.
5. Detach the transmission oil cooler line bracket from the engine.
6. Remove the right transmission cover bolt from the transmission cover.
7. Detach the starter from the engine.
8. Slide the starter forward and remove the transmission cover.
9. Remove the heat shield from the starter.
10. Position the starter so that it can pass between the engine oil pan and transmission oil cooler lines.
11. Detach the starter lead and battery positive cable from the starter.
12. Remove the starter from the vehicle.

To Install:

1. Place the starter between the engine oil pan and transmission oil cooler lines.
2. Attach the battery positive cable to the starter and starter lead. Torque the battery positive cable nut to 80 in-lb (9 Nm). Torque the starter lead nut to 30 in-lb (3.4 Nm).
3. Install the heat shield to the starter.
4. Attach the starter from the engine. Torque the bolts to 37 ft-lb (50 Nm).
5. Install the right transmission cover bolt into the transmission cover. Torque the bolt to 80 in-lb (9 Nm).
6. Attach the transmission oil cooler line bracket to the engine. Torque the bolt to 80 in-lb (9 Nm).
7. Attach the wire harness to the transmission oil cooler line bracket.
8. Install the rear steering gear crossmember onto the frame.
9. Lower the vehicle.
10. Connect the negative battery cable to the battery.

1. Disconnect battery ground cable.
2. Remove the battery.
3. Remove clip retaining constant control relay module and position module aside.
4. Remove battery tray.
5. Remove radiator cap.
6. Raise vehicle on hoist.
7. Remove radiator splash shield.
8. Drain engine cooling system.
9. Remove radiator mounting bracket assembly.
10. Remove lower radiator hose.
11. Partially lower vehicle.
12. Remove upper radiator hose.
13. Remove radiator overflow hose.
14. Remove upper A/C condenser core retaining bolts.
15. Remove upper A/C transmission oil cooler tube clips.
16. Remove upper transmission oil cooler tube (7C410) using 3-8 inch fuel line disconnect tool 310-041 (T90T-9550-C).
17. Raise vehicle on hoist.
18. Remove lower transmission oil cooler tube clips.
19. Remove lower transmission oil cooler tube using 3/8 inch fuel line disconnect tool 310-041 (T90T-9550-C).
20. Remove transmission oil cooler bracket and position transmission oil cooler aside.
21. Remove lower A/C condenser core bolts and position A/C condenser core (19712) aside.
22. Remove radiator support bracket.
23. Remove radiator.

Disconnect battery ground cable. Remove battery. Remove battery tray. Remove clip retaining contant control relay module and position module aside. Remove radiator cap. Raise vehicle front end as high as possible. Remove radiator splash shield. Drain radiator. Remove the radiator mounting bracket assembly. Remove lower radiator hose. Partially lower vehicle. Remove upper radiator hose. Remove radiator overflow hose. Remove upper A/C condenser core retaining bolts. Remove upper transmission oil cooler tube clips. Remove lower transmission oil cooler tube. Raise vehicle. Remove lower transmission oil cooler tube clips. Remove lower transmission oil cooler tube. Remove transmission oil cooler bracket and position transmission oil cooler aside. Remove lower A/C condenser core bolts and position A/C condenser core aside(be careful not to loosen the AC condenser lines. Remove radiator support bracket. Remove radiator out through the bottom of the vehicle.
Installation
Position radiator. Position radiator support bracket and tighten nuts. Position A/C condenser core and tighten lower A/C condenser core bolts. Position transmission oil cooler tube and install transmission oil cooler tube bracket. Install lower transmission oil cooler tube. Install lower transmission oil cooler tube clips. Install lower radiator hose. Install radiator mounting bracket assembly. Tighten bolts. Install radiator splash shield. Lower vehicle. Install upper tranmission oil cooler tube. Install upper transmission oil cooler tube clips. Install upper A/C condenser core retaining bolts. Tighten bolts. Install radiator overflow hose and tighten clamps securely. Install upper radiator hose. Position constant control relay module and clip securely. Install battery tray. Install battery. Connect battery ground cable. Fill and bleed cooling system. Start engine and inspect for leaks.

I Hope you Find this Helpfull And Please Remember to RATE ME

1. Drain the coolant.
2. Disable the SIR.
3. Move the forwarding discriminating sensor out of the way.
4. Remove the air cleaner assembly.
5. Remove the cooling fans.
6. Disconnect the radiator inlet hose from the radiator.
1. Disconnect the radiator outlet hose from the radiator.
2. Disconnect the engine oil cooler lines from the right radiator end tank.
3. Disconnect the transmission oil cooler lines from the left radiator end tank.
4. Remove the left and the right engine torque struts.
1. Remove the upper radiator support screws.
2. Remove the radiator from the vehicle. Lift the radiator up and out. INSTALLATION PROCEDURE
1. Install the radiator to the vehicle.
2. Install the upper radiator support screws. Tighten the bolts to 6 Nm (53 inch lbs.). NOTICE: Refer to Fastener Notice in Service Precautions.
3. Install the transmission oil cooler lines to the radiator. Tighten the transmission oil cooler line fittings to 27 Nm (20 ft. lbs.).
4. Connect the engine oil cooler lines to the radiator. Tighten the engine oil cooler lines to 18 Nm (13 ft. lbs.).
5. Install the left and the right engine support torque struts.Connect the radiator outlet hose to the radiator.
1. Connect the radiator inlet hose to the radiator.
2. Install the cooling fans.
3. Install the air cleaner assembly.
4. Install the forward discriminating sensor.
5. Enable the SIR.
6. Refill the coolant.
6. Hope this Helps and PLEASE RATE ME

YOU NEED TO TAKE IT OUT FROM THE BOTTOM REMOVE PLASTIC SHROUD THEN DRIAN AND PULL LOWER RADIATOR HOSE FROM RADIATOR AND THE REST IS PRETTY SELF EXPLANATORY MAKE SURE YOU BUY THE CLIPS FOR THE WIRRING BEFORE YOU EVEN START

THIS IS a 1995 LINCOLN CONTINENTAL W/4.6L ENGINE
iIBELIEVE TOWN CAR IS DIFFERENT LET ME KNOW IF SO AND PLEASE DONT FORGET TO RATE ME


REMOVAL

1. Disconnect battery ground cable (14301).
2. Drain engine coolant.
3. Remove engine air cleaner (ACL) (9600).
4. Remove upper radiator hose (8260) from water bypass tube.
5. Remove radiator overflow hose (8075) from radiator (8005) and fan shroud (8146). NOTE: Loosen transmission oil cooler lines while securely holding radiator connector with a back-up wrench.
6. Remove transmission oil cooler line from oil cooler inlet fitting.
7. Remove nuts retaining A/C condenser core to the radiator.
8. Disconnect engine control sensor wiring (12A581) from the auxiliary electric cooling fan motors and the CCRM.
9. Raise vehicle on hoist.
10. Remove splash shield from lower radiator support (16138) and front sub-frame (5C 145).
11. Remove lower radiator hose (8286) from radiator. NOTE: Loosen transmission oil cooler lines while securely holding radiator connector with a back-up wrench.
12. Remove oil transmission cooler line from oil cooler outlet fitting on radiator.
13. Remove retaining screws for power steering/transaxle oil cooler and position cooler aside.
14. Support fan shroud, radiator and A/C condenser core (19712) with a suitable jackstand. Remove lower radiator support. Position jackstand aside and carefully remove radiator and fan shroud.

1. Remove two retaining bolts for fan shroud at top of radiator and remove fan shroud from radiator.
2. Remove upper radiator hose from radiator.

INSTALLATION

1. Follow removal procedure in reverse order.
2. Tighten fan shroud bolts and A/C condenser core nuts to radiator to 3-5 Nm (27-44 inch lbs.) .
3. Tighten lower radiator support bolts to 8-11 Nm (71-97 inch lbs.) .
4. Tighten transmission oil cooler lines to fittings to 25-28 Nm (18-21 inch lbs.) .
5. Tighten power steering/transaxle oil cooler and splash shield retaining screws securely.
6. Refill engine coolant.