How to remove drivers door panel - 1996 Ford Crown Victoria

Remove mirror mount cover assembly.
Remove inside door handle cup (22634).
Remove door lock control bezel.
Remove window control bezel.
Remove interior lamp lens.
Remove screw from interior lamp assembly body.
Remove screw from window control bezel opening.
Disconnect mirror, lock switches and memory seat on driver side from bezels and wire harness.
Disconnect window switches from window bezel and wire harness.
Lift front door trim panel (23942) vertically, out of weatherstrip and over lock rod.
Disconnect interior lamp (13776) from wire harness.
Remove front and rear door trim retention hooks into door inner panel.
To install, reverse Removal procedure, paying special attention when inserting inner door trim into weatherstrip. Rock inner door trim into weatherstrip and push downward until lower trim belt character ditch lines up with score mark on inner door panel.

First disconnect negative battery terminal.Underneath of armrest there is two screws, remove them, using small screw driver pry out armrest switch control plate and remove screw behind it, pry of the side mirror cover using wide putty knife. carefully start prying from the bottom of the door around going toward the top then lift the door panel over door lock knob. Carefully look under and disconnect all electrical connectors and remove the panel. Installation is in reverse order of removal!

Trim and molding remove tool and a phillips screw driver
Drivers Side

Remove
Door trim panel and water shield (top where window is)
Plastic panel around door handle. snaps out
1 screw upper front extension assembly (plastic triangle)
2 screws located lower bottom left (drivers side) and door trim panel
Use remove tool to push out retaining 'C' clip behind door handle
Grasp panel where opening are and pull up and out gently
Now disconnect wire harness

DOOR PANEL REMOVAL

Its just fitted with few screws and hidden lock clips. The clips are very delicate and can break easily. But no worry, the clips are easily available.

On some vehicle models these screws are hidden. Once the panel is loose, don't just pull it out, there are few wire connectors connected, first disconnect the connector plug, then lift the panel out and keep in safe place for re-installing.

For your help, there are few very helpful similar help links with diagrams and solutions to make your task easy. Click the link below:----

How to Remove Door Panels on Acura Integra
http://repairhelpcenter.blogspot.com/2011/11/how-to-remove-door-panels-on-acura.html

-------

How to Access car door panel?
http://howtobyme.blogspot.com/2011/11/how-to-access-car-door-panel.html

---------

Vehicle door panel components?

http://howtobyme.blogspot.com/2011/11/vehicle-door-panel-components.html

----------
How to remove the door panel to install a new window regulator on Cadillac Deville?
http://howtobyme.blogspot.com/2011/08/how-to-remove-door-panel-to-install-new.html ---------------
Hummer H2 Door Panel Removal? http://technoanswers.blogspot.in/2012/07/hummer-h2-door-panel-removal.html

-------
Hummer H2: How to remove Front Door panel? http://www.howtobyme.blogspot.com/2012/07/hummer-h2-how-to-remove-front-door.html

--------------
2009 Hummer H2 Door Panel Removal

http://schematicsdiagram.blogspot.in/2012/07/2009-hummer-h2-door-panel-removal.html

-----------

how to remove window motor on driver side door panel on 1994 Oldsmobile Cutlass Ciera
http://technoanswers.blogspot.com/2011/08/how-to-remove-window-motor-on-driver.html

------------

How to remove door panel, door window motor and regulator on 1991 cavalier?
http://technoanswers.blogspot.com/2011/05/how-to-remove-door-panel-door-window.html

-------------
how to remove rear window inner panel on Hyundai Elantra?
http://technoanswers.blogspot.com/2011/05/how-to-remove-rear-window-inner-panel.html

------------
ford explorer window motor, regulator and door panel removal?
http://technoanswers.blogspot.com/2011/02/ford-explorer-window-motor-regulator.html

------------
These details will help.

Thanks,.

Click the link below:-----Door Panel Removal?

--------
How to remove the door panel to install a new window regulator?
http://howtobyme.blogspot.com/2011/08/how-to-remove-door-panel-to-install-new.html

---------
Hummer H2 Door Panel Removal? http://technoanswers.blogspot.in/2012/07/hummer-h2-door-panel-removal.html Hummer H2: How to remove Front Door panel? http://www.howtobyme.blogspot.com/2012/07/hummer-h2-how-to-remove-front-door.html 2009 Hummer H2 Door Panel Removal http://schematicsdiagram.blogspot.in/2012/07/2009-hummer-h2-door-panel-removal.html

-----------
how to remove window motor on driver side door panel?
http://technoanswers.blogspot.com/2011/08/how-to-remove-window-motor-on-driver.html

-----------
ford explorer window motor, regulator and door panel removal?
http://technoanswers.blogspot.com/2011/02/ford-explorer-window-motor-regulator.html

---------
Keep updated for more help.

1. Remove 2 small screws at bottom of the door panel (6mm)
2. Remove small black cover from inset for door handle (pry it out carefully with a small flat head screw driver or panel removal tool) and remove bolt behind it (8mm)
3. Pop window/door lock control panel out with the same flat head screw driver and disconnect all connectors. Remove small screw from behind it (6mm)
4. Lift straight up on door panel and then tilt toward you.
5. Disconnect mirror control connector.
6. Squeeze two tabs on the door latch assembly and it can be removed along with the cable. DONE.

Front Door Panel - Town Car - Removal
CAUTION: To avoid breakage of door pull cover(s), insert a screwdriver diagonally between pull strap and chrome bracket. Snap out both sides then remove.

Snap out two door pull strap retaining screw covers. Remove screws.

Remove two screws on front and rear side of front door trim panel.
The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.
Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.

NOTE: Do not use front door trim panel (23942) to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.

Remove window regulator control switch housing from back of front door trim panel . Lift up housing, remove retaining screws and disconnect all connectors.

Disconnect driver seat regulator control processor switch (driver door only) if equipped.
Twist out interior lamp wire assembly and remove the front door trim panel.
Installation

Ensure plastic watershield is secured to door panel.
Position front door trim panel to door. Connect interior lamp wiring.
Position the window regulator control switch housing and connect switch connectors. Install the retaining screws.
Connect driver seat regulator control processor (14C708) (driver door only) if equipped.
Align door lock side to its mating slide on the sheet metal (front doors only).
Snap in front door trim panel. Ensure all retainers fit properly.
Install two retaining screws on front and rear side of front door trim panel .
Install two retaining screws and pull strap covers.

Good luck Remember rated this).

Generic instructions to remove door panels:

1. Remove the screw(s) in the trim behind the door release handle and remove the trim.
2. Look for the screws in the arm rest and remove. Remove the arm rest.
3. Look for other screws (possibly under caps) and remove them.
4. Insert a wide flat blade between the door panel and the door. Find the plastic tabs which hold the panel to the door and gently pry the panel away from the door. Make sure you work as close to these plastic tabs as possible to avoid ripping the panel.
5. Work your way around the door prying the tabs out of the door.
6. When everything is free, gently lift the door panel straight up and out of the door.
7. Disconnect the electrical wires, and you are done.
8. There is a vapor barrier between the door and panel which must be gently peeled out of the way in order for you to gain access to the window and door latch mechanisms.

try to look at stress point on door by handle normally two screws and under neath panel to screws also disconnect side panel for side mirror door of using panel popper

Remove the sail panel,the little panel on inside of door at the mirror.
Remove the window regulator switch plate, pry up on the front of it with a small pick or screw driver. Disconnect the electrical connectors.
Remove the top door trim panel screw that is behind the sail panel you removed.
Remove door trim panel screw at window regulator switch plate opening.
Remove door trim panel screw in the courtesy lamp housing. Remove the courtesy lamp lens.Remove the screw.
Remove the inside door handle trim cover.
Remove the bolt.
Remove the inside door handle.
Lift upward to remove the front door trim panel.
Remove the courtesy lamp.
Turn the courtesy lamp bulb socket one quarter turn and remove.
Disconnect the power mirror electrical connector.
Remove the three outside rear view mirror nuts.
Remove the mirror.