Question about 1996 Ford Ranger SuperCab

1 Answer

Bill Boyd i have change clutch and pressure plate and there is a lot of pressure on clutch what else can be the problem

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Ford Master
  • 1,288 Answers
Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I was driving my golf mk1 and when i pushed in the clutch to change gears it starter to make a lot of engine noise removing the stater i noticed aliminium shavings in the starter ring gear compartment


There should be about 3/4" play in the clutch pedal if there isn't the clutch operation will affect the clutch performance. The over adjustment throws the release bearing further into the clutch pressure plate and this in turn will damage the pressure plate

Aug 22, 2018 | Volkswagen Golf Cars & Trucks

2 Answers

Clutch stays down. Slowly will take of with clutch fully pressed. Does not slip.dont understand


It sounds as though the clutch pressure plate has become weak.

When you press the clutch pedal the release/throwout bearing presses against the centre of the clutch pressure plate. This causes the metal 'fingers' -the springs- on the pressure plate to flex and release pressure on the driven plate - momentarily disconnecting the drive from engine to gearbox.

The link below is of generic clutch images
how clutch works Google Search

A weak pressure plate isn't fully releasing the driven plate. If you're going to do any replacing of parts - a clutch should be replaced in 3 units: Pressure plate, driven plate and release/throwout bearing.

May 05, 2016 | Cars & Trucks

2 Answers

Hyundai. Tucson, 59 plate' clutch slips at high speed when changing gear


check /replace clutch cable or replace master cylinder. If the clutch has not been replaced it may need a clutch kit as the indications are that the pressure plate is weak ( worn clutch plate or from overheated clutch)

Feb 10, 2015 | Hyundai Tucson Cars & Trucks

2 Answers

On a 04 Nissan Frontier I replaced the clutch. After several months shaking really bad when I let out on the clutch in first gear. It never does it when cold only after driven awhile.


clutch shudder is from hot spots on the flywheel ,hot spots/warped pressure plate, oil on the flywheel face /pressure plate face, faulty engine mounts. many people think that it is just a matter of replacing the clutch plate but this always results in a poor performing clutch
Installing a clutch kit without first removing the protective coating on the pressure plate is a problem as well
Incorrect tightening sequence of the pressure plate bolts will cause a deformed pressure plate cover resulting in clutch engagement problems
If you have a cable clutch then that is made worse by bad engine mounts. Remember what you did and what you should have done and you will have the answer as to why it is shuddering on take off.

Feb 07, 2015 | 2004 Nissan Frontier

2 Answers

My clutch seems to have gone out tonight. The clutch is very easy to push to the floor...and it pops back....there's no pressure at all. The clutch fluid is leaking from the hose. Could this be the...


it could be either the master cylinder or the slave cylinder,it could also be the clutch pressure plate check the master & slave cylinders first because if it's the pressure plate the gear box will have to be removed to replace the pressure plate, even if you are uncertain it is most likely cheaper to replace the master & slave cylinders than it would be to replace the pressure plate.....hope this helps......cheers.

Aug 31, 2011 | Saturn Vue Cars & Trucks

1 Answer

2002 Kia Optima. Replacing manual clutch, pressure plate, and clutch bearing. Do you have procedure manual. Thanks Bill


in a front wheel drive car you need to first disconnect all sensors take off wheels take off controll arm,half shaft, ball joint, front,side,and rear motor mounts remove front exhaust pipe, change control rod, stationary control rod, unhook battery, remove joint shaft, starter, tie rod end, right and left axle..... there is a lot of disassemble but if you are ready for the job then go to autozone.com sign up its free then click on repair manuals you will find all of your info there....good luck

May 24, 2010 | 2004 Kia Optima

2 Answers

2005 rodeo 4wd turbo diesel


possibly the throw out bearing....which is part of the clutch assembly

Oct 09, 2008 | 2004 Isuzu Rodeo

1 Answer

91 legend clutch specs


I am assuming you have never installed a clutch before. What you are asking about is a clutch alignment tool. It is a tool made from plastic that is identical to the output shaft of the transmission.

As you put the clutch disc, pressure plate up against the flywheel, just start the 6 or 8 bolts, but before tightening them down, push the clutch alignment tool all the way into the flywheel pilot bearing. The trick of this tool is to get a close approximation of alignment between the pressure plate, clutch disc and flywheel before tightening down the pressure plate bolts.

Depending on how good your eye is, will determine how easily your transmission will line up and slide in place.

As for any specs, there are none. It all in the eye.

Bill

Sep 21, 2008 | 1991 Acura Legend

Not finding what you are looking for?
1996 Ford Ranger SuperCab Logo

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...