When I crank engine I get spark but then it quits same with injectors thy work for a second then quit
SOURCE: car has no spark or injector pulse(new ecm,crank sensor)
Check the fuse for the injectors, some vehicles have the injectors and coil running on the same circut, at the same time check the fuse for the ignition.
SOURCE: 1985 corvette no pulse to injectors
Very important that if you are not savvy of working on your Vette ...you would be better off - taking your car to a dealership for repairs on your trouble codes. However if you feel that you want to, First locate your car's alcl this component is located just below the instrument panel and to the left of the center console. Remove the plastic cover the first two slots to your right are the A & B slots.
The A slot is the diagnostic slot and the B slot is the ground slot. Insert the computer key into these slots if you do not have a computer key, a paper clip or wire jumper clip will do, (with the engine off) this is very important...now only put the ignition key to on ( not start !!!) the check engine light will display a code 12 which is one flash followed by two flashes. This code will be flashed three times ..followed by the trouble code stored in your car's computer.
What ever the code is it will be flashed three times. Have a paper and pencil ready and write down the code.
Code #12: Normal No Codes.
Code #13: Open Oxygen Sensor Circuit.
Code #14: Coolant Sensor Circuit Low.
Code #15: Coolant Sensor Circuit High.
Code #21: Throttle Position Sensor High.
Code #22: Throttle Position Sensor Low.
Code #23: Manifold Air Temperature Circuit High.
Code #24: Vehicle Speed Sensor.
Code #25: Manifold Air Temperature Circuit Low.
Code #32: EGR System Failure.
Code #33: Mass Air Flow Sensor High.
Code #34: Mass Air Flow Sensor Low.
Code #36: Mas Air Flow Sensor Burn-Off Function Fault.
Code #41: Cylinder Select Error.
Code #42: Electronic Spark Timing.
Code #43: Electronic Spark Control.
Code #44: Lean Exhaust indication.
Code #45: Rich Exhaust Indication.
Code #46: Vehicle Anti Theft Fault.
Code #51: Faulty Mem-Cal.
Code #52: Fuel Calpak Missing.
Code #52(1990-91 Corvette Only): Engine Oil Temperature Sensor Low.
Code #53: System Over Voltage.
Code #54: Fuel Pump Circuit Low Voltage.
Code #55: Defective ECM.
Code #62: Engine Oil Temperature Sensor Circuit High.
Please remember that if you have the computer key installed in the alcl and you start the engine (you will ruin the engine's computer) only put the ignition to on (not to start).
If you should get a check engine soon display.. you can use the above procedure and codes to buy the right part or at the very least to keep from getting taken for a ride and be made to pay hight prices for some inexpensive module that you could have installed yourself.
If your engine displays a trouble code ... your engine will go into limp mode ..it will still run but very poorly. You might be able to reset the computer if it will not start (just to get home) by disconnecting both battery cables and re-installing them ...this is not recommended ..but if you are stranded it might help unitl you get your car home or to a repair shop..good luck.
Good luck and hope this helps.
SOURCE: Have a 2003 Taurus, 3.0 engine that has a misfire
did you check the injector pulse on that cylinder and it also could be the pcm , i had a taurus and a sable with good coils stop firing 2 cylinders and it was the pcm ,the code it gave was secondary coil but changed the pcm and it worked fine
SOURCE: 1995 dodge intrepid 3.3L cranks
The injectors are mainly controlled by the good output of an auto shut-down relay which is directly affected by the fuel pump relay straight from the PCM.The easiest way to check the fuel pump relay is turn on the key,wait a minute,and see if the fuel guage comes up to proper level,helps if you know fairly close how much gas you do have.A couple other things which could cause intermittent cranking are the ignition switch may be going bad,or a bad connection in the ignition wire harness but the ignition itself is way more common.Also a near dead battery.The lights will sometimes appear somewhat bright but to start requires lots and lots of power.A good battery should read near 13V.A bad one will read around 11.8,11.9V and could cause intermittent crank.A crank position sensor could cause it,but for the most part,if a sensor is bad the system either works or it does not.That's about all except do you have intermittent start or no start whatsoever,even jumpers?If this doesn't work or you need more help,just comment here and I will get an autolink to your post and reply ASAP.Good luck! Greg
116 views
Usually answered in minutes!
×