Dmax LS. What are the probable causes of DTC P1520?

Code P1520 Isuzu Commanded Versus Actual Throttle ...

AutoCodes https://www.autocodes.com > p1520_isuzu
Code P1520 Isuzu Possible Causes · Faulty Throttle Valve Motor · Throttle Valve Motor harness is open or shorted · Throttle Valve Motor circuit poor electrical ...

N switch position on error p1520 fault code op isuzu kb 300

Fixya https://www.fixya.com > ... > Cars & Trucks > Isuzu
Clearing the codes is simple that is done by removing the fuse of the EFI from junction box 2 for 10 seconds. Make sure to remove the jumper wire and switch the ...

P1520 Isuzu Code Meaning, Causes, Symptoms, & Tech ...

Engine-Codes.com https://www.engine-codes.com > p1520_isuzu
Faulty Throttle Valve Motor · Throttle Valve Motor harness is open or shorted · Throttle Valve Motor circuit poor electrical connection.

What is the solution to the code P1520 Isuzu 4jh1 2006. ...

AutoTrader South Africa https://www.autotrader.co.za > answers > What-is-the-s...
Feb 23, 2020 - According to engine-codes.com, that error points towards an intake manifold runner malfunction on Isuzu engines. In the case of the 3.0 8V ...
1 answer · 0 votes: Hi there According to engine-codes.com, that error points towards an intake manifold runner malfunction on Isuzu engines. In the case of the ...

Thread: 300 tdi engine management light

4x4 Community Forum https://www.4x4community.co.za > ... ·Translate this page Jan 25, 2014 - Exclamation P1520(b) neutral switch error - No power Loss ... I have a 2005/2006 Isuzu KB300 lx d/cab, recently imported from SA to Zimbabwe. I ...

is anything I can do? Don't know , do you know how to test electrical circuit's using a DVOM - digital volt ohm meter ? Do you know what a wiring diagram is an how to read one ? P2008 - Intake Manifold Runner Control (IMRC) Circuit Open (Bank 1) Description: This DTC indicates a failure in the IMRC primary control circuit. This DTC replaces P1520. Possible Causes:

• IMRC control circuit open

Diagnostic Aids: Monitor the IMRC and IMRCM PIDs. The IMRCM state should change when the IMRC is commanded open or closed. Application Key On Engine Off Key On Engine Running Continuous Memory All GO to Pinpoint Test HU .

P2008 code on 2005 ford focus

P0128- Coolant Temp below Thermostat. Sounds like the thermostat is stuck open. Do you get heat from the heater when the car is at operating temp. if not I would start there. Hope this helps.


This is the
TThis

code p 0108 refers to manifold absolute pressure (MAP) sensor/ barometric pressure(BARO) sensor---high input===causes ---wiring short to positive ---MAP sensor---BARO sensor---ECM
Check /replace the sensors

Temp sensor or fan control switch or the A/C is engaged causing the fan to run at high speed

I found a site for you with the diagnostic codes. There's information available on the site to help you figure out what is causing what ever fault code is coming up and help you figure out what to do to fix it.
Best of luck to ya.
http://www.engine-light-help.com/ford-check-engine-light.html
P1520 Intake Manifold Runner Control Fault

You'll need to remove your power steering pump to access the sensor. Remove the small bolt holding the sensor located right in front of the intake manifold for 3.5 and 3.9 engines.

Good luck

O/D light blinks, but with that the check engine light is ON.--- This will make your troubleshooting easier.When the check engine light comes on, and remains on, this indicates that there is error stored in your cars computer.---- Once the computer is scanned, you will get error codes, as per that error code it will point towards faulty part, which is causing the O/D light to blink.-------- Most probably the O/D light blinks, If a problem exists in No. 1 or No. 2 solenoids or speed sensors .
--------------- For car after 1995 it requires OBD2 tool and for car before 1995 it requires OBD1 tool.------- --------- You car will require OBD1 tool.There are very few auto parts store and repair centers who have OBD1 tool.In your case you required OBD1 tool.------ You can just contact local auto-parts store and they will guide you to the nearest store who has OBD1 tool.There you can get your car scanned.If there is error set in your cars computer, then you will receive the error code.As per error code it will point towards the faulty part causing this problem in your car.------------- -------------- The codes which you get is scanning will be mostly any of this following codes:--- DTC P0500 - Vehicle Speed Sensor Malfunction
. DTC P0750 - Shift Solenoid "A" Malfunction
. DTC P0753 - Shift Solenoid "A" Electrical Malfunction
. DTC P0755 - Shift Solenoid "B" Malfunction
. DTC P0758 - Shift Solenoid "B" Electrical Malfunction
. DTC P0770 - Shift Solenoid "E" (SL) Malfunction
. DTC P0773 - Shift Solenoid "E" (SL) Electrical Malfunction
. DTC P1520 - Stop Light Switch Signal Malfunction
. DTC P1705 - Direct Clutch Speed Sensor Circuit Malfunction
. DTC P1765 - Shift Solenoid Valve SLN Circuit Malfunction
. DTC P1780 - Park/Neutral Position Switch Malfunction --------------- Now it all depends on what code you get, as per that you can replace the following part.------- This will help.Thanks.Helpmech.

P1520? Intake Manifold Runner Control circuit fault
P1520? Intake Manifold Runner Control fault
Possible Causes:


IMRC control circuit is open or shorted to ground IMRC Monitor VREF circuit is open IMRC is damaged or the PCM has failed
Most likely not the last one as that would be the last thing to check and I doubt it's the PCM.
Thank you,
Lee

There is NO SUCH CODE as P1520... However, there is a Code as P1529 - TCM MIL request to ECM This is a transmission trouble code.
Whenever the 'CHECK ENGINE' light comes on, the ECU (Engine Control Unit) sets a Diagnostic Trouble Code (DTC). These codes identify the particular engine management system which caused the light to come on. You'll need to use/find an OBDII (On-Board Diagnostic) Scanner to retrieve any code which have been stored in the ECU computer. Afterward, we might be able to help you DIAGNOSE and perhaps eventually fix the problem.