Question about Hyundai Cars & Trucks

1 Answer

Does anyone know where i can get a crank shaft for a hyundai h100 2.6 the bakkie with the round head lights. Annelize

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Hyundai Master
  • 53,755 Answers

Wreckers , spare parts at service dealer, engine reconditioner engineering shops
get yours ground

Posted on Apr 28, 2016


4 Suggested Answers


6ya staff

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017



  • 96 Answers

SOURCE: need to know how to

the 2.4 i believe the sensor is under the front plastic cover that hides the belts at the bottom of the engine, if it is i wouldnt recommend doing it your self, most of them require you to remove the timing belt (which i do recommend replacing at that time) to replace the sensor which is not easy to do if you dont have all the tools and knowledge or experience doing them.

Posted on Aug 01, 2008


Paul McGrath

  • 776 Answers

SOURCE: change the timimg belt on a 1998 hyundai accent

Go to and register (vehicle by VIN). Afterward, you'll have access to technical information (manuals, wiring diagrams, service bulletins, etc) about your vehicle.

Posted on Jun 17, 2009


Steven Mitchell

  • 68 Answers

SOURCE: crank shaft position sensor located hyundai sonta 2004 v6

On a 2.7L it is located above and to the right of the starter. You will have remove the starter heat shield to gain access to it.

Posted on Jun 25, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Crank shaft position sensor on a 2007 hyundai santa fe 3.3 cant find location

located on the bell housing of the transmission under left cylinder head or radiator side of engine

Oct 23, 2017 | Hyundai Santa Fe Cars & Trucks

1 Answer

Does anyone know if the Nissan 1400 bakkie has a pilot bearing or bush at the back do the crank. Many Thanks to Dan for answering my last question thanks you.

I've never seen a manual transmission vehicle without one. It will be seated in the flywheel plate. Transmission side.

Jun 27, 2017 | Nissan Cars & Trucks

1 Answer

Hyundai 1.6 Elantra gls, does the spark come from the cylinder head or the crank shaft

the crank shaft position sensor triggers the ignition control module that generates the spark either internally or through a coil/ pack
the cam position sensor ok, s that process to prove that the cam shaft is turning correctly

Apr 13, 2017 | Hyundai Cars & Trucks

1 Answer

I want to install timing belt on my colt bakkie 4G63, The mark on the head nd it doesn't have balancing shafts.

Old ones have a mark on the timing belt, and you need a timing light that flashes on the belt; then turn the distributor til it has the right count.

Oct 05, 2016 | Cars & Trucks

1 Answer

Crank shaft position sensor located hyundai sonta 2004 v6

On a 2.7L it is located above and to the right of the starter. You will have remove the starter heat shield to gain access to it.

Jun 24, 2009 | 2005 Hyundai Sonata

1 Answer

I am doing a head gasket setting alignment

you will find two bright links on the chain that correspond to the dots on the cam shaft and the key ways on both cams should line up with the top of the head facing back towards the firewall IE parallel with the top surface of the head ( where the tappet cover bolts on), with the crank on TDC (top dead center)

Apr 19, 2009 | Hyundai Excel Cars & Trucks

1 Answer

My 03 Hyundai Santa Fe is slipping out of gear while im driving

Sounds like the clutch is slipping . You will need a new clutch assembly and fly wheel. Also make sure the crank shaft end play is not excessive.

Mar 18, 2009 | 2003 Hyundai Santa Fe

2 Answers

Door Handle

put thin piece of cloth between window crank, twist it around, turn window crank up and down, then pull thin piece of cloth away from the round spinable crank ball (piece you hold) this shud remove interior hidden C clip. try again if you dont succeed. those tools they sell wont fit and will scratch the door panel. I am having probs in removing the door handle and lock mechanism... removed screw, yet still attched. grrrr

Feb 04, 2009 | 2002 Hyundai Accent

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts


Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides