Crankshaft sensor location - 2007 Ford Edge

Text based articles, diagrams and videos

https://www.google.com/search?q=1988+chrysler+conquest+crankshaft+position+sensor+location

..

Question edited for clarity.
Question moved to model category.

Crankshaft position sensor location - Colorado Fans

coloradofans.com https://www.coloradofans.com > threads > crankshaft-...
Dec 16, 2009 - Hey everyone.. do ya know where the crankshaft position sensor is located on our engines? It would be a big help if someone could point me ...

Crank Positioning Sensor Relearn - Colorado Fans
Oct 7, 2006
No start after replacing Camshaft Position Sensor
Mar 2, 2012
Camshaft Crankshaft sensor ' Chevy Colorado & GMC Canyon
Feb 22, 2015
Colorado won't start after replacing the Camshaft Actuator ...
Sep 11, 2012
More results from www.coloradofans.com
..

There is normally only one crankshaft sensor, maybe 2 camshaft sensors, one for each bank, and there are two O2 sensors for each bank.

https://www.google.com/search?q=2009+Hyundai+Santa+Fe%2C+2.7%2C+6+cylinder.+Where+is+the+location+of+the+crankshaft+bank+1+sensor+A

Crankshaft Position Sensor, only one

https://www.google.com/search?q=2009+hyundai+santa+fe+crankshaft+position+sensor+location

..

https://www.google.com/search?q=Crankshaft+position+sensor+location+93+ranger+4.0+4x4&rlz=1C1CHBF_enUS982US982&oq=Crankshaft+position+sensor+location+93+ranger+4.0+4x4&aqs=chro -------------------https://www.google.com/search?q=Crankshaft+position+sensor+location+93+ranger+4.0+4x4&rlz=1C1CHBF_enUS982US982&oq=Crankshaft+position+sensor+location+93+ranger+4.0+4x4&aqs=chrome..69i57j33i299l3.7225j0j7&sourceid=chrome&ie=UTF-8#kpvalbx=_VCj-YqCEB6GpptQPza2F-AU28

Top part says you want Camshaft Sensor, but the bottom says you want Crankshaft Sensor??

Camshaft
https://www.google.com/search?q=2012+dodge+caliber+3.0+camshaft+sensor+location

Crankshaft
https://www.google.com/search?q=2012+dodge+caliber+3.0+crankshaft+sensor+location

..

crankshaft position sensor location for 3.3 V6 engine is mounted at the rear of the engine on transmission bellhousing, the 3.5 V6 engine crankshaft sensor located at front of the engine on the aluminum oil pan section below crankshaft pulley.replace the crankshaft position sensor remove heat shield disconnect the electrical connector the remove sensor retaining bolt then remove crankshaft sensor.after replacing crankshaft sensor you need to erase code if check light come back on.

The crank sensor is located on the engine near the flywheel axis of the crankshaft.

Crankshaft Position Sensor Removal & Installation To Remove:
Location of the crankshaft position sensor on the 2.4L engine
Location of the crankshaft position sensor on the 3.0L engine
Location of the crankshaft position sensor on the 3.3L and 3.8L engines
NOTE: On the 2.4L engine, the crankshaft position sensor is mounted to the engine block behind the alternator, just above the oil filter. On the 3.0L, 3.3L and 3.8L engines, the crankshaft position sensor is mounted on the transaxle housing, above the vehicle speed sensor.

1. Disconnect the negative battery cable.
2. Raise and safely support the vehicle.
3. Disconnect the crankshaft position sensor electrical connector.
4. Unfasten the sensor mounting screw, then remove the sensor from the vehicle by pulling it straight out.

To Install:
NOTE: If the sensor removed is going to be re-installed, clean off the old spacer on the sensor face. A new spacer must be attached to the sensor face before installation. If the sensor is being replaced, be sure that a paper spacer is attached to the sensor face.

1. Install sensor and push the sensor in until contact is made. While holding the sensor in this position, install and tighten the mounting bolt to 105 in. lbs. (12 Nm).
2. Connect the crankshaft position sensor electrical connector.
3. Lower the vehicle.
4. Connect the negative battery cable.

The 2 crankshaft sensors are located on the front of the engine block, between cylinder Numbers 4 and 6. Crankshaft position A sensor is located on the upper crankcase and crankshaft position B sensor is located in the lower crankcase. Both sensors extend into the crankcase and are sealed into the engine block with O-rings. The crankshaft position sensors are not adjustable.

Hi!!

here are illustrations of the CKP (crankshaft position) sensor in 2.3L and 3.0L.

Note: In the bottom of the 2.3L drawing says Trottle Position (TP) Sensor, this is wrong, It should say CKP Sensor.


2.3L Engine


The Crankshaft Position (CKP) sensor is located to the left of the crankshaft pulley.

Fig. Crankshaft Position (CKP) sensor location-2.3L engine


3.0L Engine


The Crankshaft Position (CKP) sensor is located just behind the crankshaft pulley on engine block.

Fig. Crankshaft Position (CKP) sensor location-3.0L engine

The cost of the sensor is $23 bucks at AutoZone.

If helpful, click below

can u please tell me where on my 2004 chrysler pacifica is the crankshaft sensor located?