Question about Honda Ridgeline

Open Question

Repair open in the wire between the A/F sensor Sensor 1 and the A/F sensor relay LAF

How to Repair open in the wire between the A/F sensor Sensor 1 and the A/F sensor relay LAF? thanks.

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 625 Answers

SOURCE: O2 sensor wiring diagram for 2004 hyundai sonata

there is two wires then suposed to be same color they are not what you looking for but if you have a grey and a black wires it willl be one of those i hope and this help

Posted on Jun 20, 2008

Ad

Anonymous

  • 497 Answers

SOURCE: F-150 oxygen sensor diagrams

will help u in a moments time

Posted on Jun 29, 2008

juggernautxt

juggernautxt

  • 145 Answers

SOURCE: Code: P0133 - O2 Sensor Circuit Slow Response Bank 1 Sensor 1

is this a 4 or 6 cylinder?
if a 4 cylinder it will only have 2 o2 sensors
V6 will have 4 o2 senors which the sensor will be the right side of the engine first sensor.
1st sensor on exhaust, I recommend if you change one change all, as this will make the computer when it rechecks the system you have all clean/fast responding sensors.

if you have a slow response it means the sensor is dirty and not reading well, which is usually caused by minor misfires that the engine computer dismisses, so a tune up would be recommended too.

Posted on May 06, 2009

Anonymous

  • 2 Answers

SOURCE: SL2 Won't start; previous codes=PO

I HAVE A 98 SATURN, WON'T EVEN TRY TO START EVERY ONCE IN A WHILE. TURNS OUT TO BE THE CRANKSHAFT POSITION SENSOR

Posted on Jul 22, 2009

dcramer531

Dcramer531

  • 1654 Answers

SOURCE: Jaguar 2002 X- Type Code P0057

Here are the locations of the fuses and relays. F-31 through f-42 probably are the one you want to look at. These are probably all tied together from looking at your codes. Your mass air flow sensor is also giving you an alarm. If your not finding any blown fuses or bad relays it might very well be the PCM (Power train control module) itself that is going bad. A dealer will have to check that out for you.
Engine compartment fuse box - fuses
Fuse Fuse Rating Colour Circuit

No. Type (amps)

F1 Cartridge 20 Blue Dip beam, High Intensity Discharge (HID) light relay.
F2 Cartridge 50 Red Ignition relay feed.
F3 Cartridge 60 Yellow ABS.
F4 Cartridge 30 Pink Rear window heater/heated mirrors relay.
F5 Cartridge 30 Pink Automatic transmission control module relay.
F6 Cartridge 30 Pink Heater blower relay.
F7 Cartridge 50 Red Power supply to passenger compartment fuse box.
F8 Cartridge 80 Black Blower module.
F9 Cartridge 50 Red Engine management system power relay.
F10 Cartridge 20 Blue Headlight power wash pump relay.
F11 Mini Not used.
F12 Mini Not used.
F13 Mini 30 Green Heated front screen right-hand side.
F14 Mini Not used.
F15 Mini 30 Green Heated front screen left-hand side.
F16 Mini 20 Yellow Left-hand dip beam, day time running lights, autolights.
F17 Mini 20 Yellow Right-hand dip beam, HID lights.
F18 Mini 20 Yellow Throttle motor supply.
F19 Mini 15 Blue Screenwash pump, rain sensing system.
F20 Mini 5 Tan Navigation display.
F21 Mini 15 Blue Side (Parking) lights.
F22 Mini 20 Yellow Accessories relay.
F23 Mini 10 Red Air conditioning compressor clutch.
F24 Mini 15 Blue Door lock power.
F25 Mini 15 Blue Direction indicators (GEM).
F26 Mini 15 Blue Horns.
F27 Mini 10 Red Automatic transmission control module, transit relay.
F28 Mini 15 Blue Ignition switch.
F29 Mini 30 Green Starter motor solenoid.
F30 Mini 30 Green Accessory sockets.
F31 Mini 10 Red Engine management relay coil.
F32 Mini 5 Tan Engine management control.
F33 Not used.
F34 Diode D3 Not used.
F35 Diode D2 Engine management control relay diode.
F36 Mini 10 Red Canister purge valve, airflow meter, throttle motor relay, power wash relay, air conditioning relay.
F37 Mini 15 Blue Engine management system, blower speed controller, road speed sensor (if fitted).
F38 Mini 30 Green Oxygen sensor heaters A.
F39 Mini 5 Tan Variable intake valves.
F40 Mini 15 Blue Automatic transmission control module.
F41 Mini 10 Red Injectors.
F42 Mini 30 Green Oxygen sensor heaters B.


dcramer531_58.jpgPassenger dcramer531_59.jpg

Posted on Jan 23, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, I am getting Faulty codes P0036, P0056, P0141, P0161 in reference Bank 1 and Bank 2 for sensors 2 on 2003 CTS.I was told the sensors where changed but codes still appear?


If the sensors were replaced an DTC'S come back has to be a wiring problem or PCM ,
The ECM detects that the HO2S heater low control circuit voltage is between 2.6-4.6 volts when the heater is commanded OFF, indicating an open HO2S heater circuit.
Is the fuse open?
All four codes refer to the heating element circuit ! there is a relay in the under hood fuse box that supplies B+ voltage to the O2 sensor heating elements . I would change that or test the relay , videos on you tube on testing relays .
MAIN Relay
--
LO SPEED Relay, HI SPEED Relay, S/P FAN Relay, PRE O2 Fuse, IGN-1 Fuse, ECM Fuse, POST O2 Fuse, and INJ Fuse
Also check
POST O2 Fuse
10 A
HO2S Bank 1 Sensor 2 and HO2S Bank 2 Sensor 2
PRE O2 Fuse
10 A
Heated Oxygen Sensor (HO2S) Bank 1 Sensor 1 and HO2S Bank 2 Sensor 1

Jul 23, 2016 | 2003 Cadillac CTS

1 Answer

TROUBLE CODE P 1613 IN WV PASSAT 99


P1102O2S Heating Circuit Bank 1 Sensor 1 Voltage Too Low/Air Leak
P1105O2S Heating Circuit Bank 1 Sensor 2 Short To Positive P1107O2S Heating Circuit Bank 2 Sensor 1 Short To Positive P1110O2S Heating Circuit Bank 2 Sensor 2 Short To Positive P1113O2S Sensor Heater Resistance Too High Bank 1 Sensor 1 P1115O2S Sensor Heater Circuit Short To Ground Bank 1 Sensor 1
P1116O2S Sensor Heater Circuit Open Bank 1 Sensor 1
P1117O2S Sensor Heater Circuit Short To Ground Bank 1 Sensor 2
P1118O2S Sensor Heater Circuit Open Bank 1 Sensor 2
P1127Long Term Fuel Trim B1 System Too Rich
P1128Long Term Fuel Trim B1 System Too Lean
P1129Long Term Fuel Trim B2 System Too Rich
P1130Long Term Fuel Trim B2 System Too Lean
P1136Long Term Fuel Trim Add. Fuel B1 System Too Lean
P1137Long Term Fuel Trim Add. Fuel B1 System Too Rich
P1138Long Term Fuel Trim Add. Fuel B2 System Too Lean
P1139Long Term Fuel Trim Add. Fuel B2 System Too Rich
P1141Load Calculation Cross Check Range/Performance
P1144Mass Air Flow Sensor Open/Short To Ground.
P1145Mass Air Flow Sensor Short To Positive.
P1146Mass Air Flow Sensor Supply Voltage.
P1155Manifold Absolute Pressure Sensor Short To Positive.
P1156Manifold Absolute Pressure Sensor Open/Short To Ground. P1157Manifold Absolute Pressure Sensor Supply Voltage.
P1160Intake Air Temperature Sensor Short To Ground.
P1161Intake Air Temperature Sensor Open/Short To Positive. P1162Intake Air Temperature Sensor Short To Ground.
P1163Fuel Temperature Sensor Open/Short To Positive.
P1164Fuel Temperature Sensor Implausible Signal.
P1171Throttle Actuation Potentiometer Sign. 2 Range/Performance P1172Throttle Actuation Potentiometer Sign. 2 Signal Too Low P1173Throttle Actuation Potentiometer Sign. 2 Signal Too High P1176Rear O2S Correction
P1177O2 Correction Behind Catalyst B1 Limit Attained
P1196O2S Heater Circuit Bank 1 Sensor 1 Electrical Malfunction P1197O2S Heater Circuit Bank 2 Sensor 1 Electrical Malfunction P1198O2S Heater Circuit Bank 1 Sensor 2 Electrical Malfunction P1199O2S Heater Circuit Bank 2 Sensor 2 Electrical Malfunction P1213Injector Circuit Cylinder 1 Short To Positive
P1214Injector Circuit Cylinder 2 Short To Positive
P1215Injector Circuit Cylinder 3 Short To Positive
P1216Injector Circuit Cylinder 4 Short To Positive
P1217Injector Circuit Cylinder 5 Short To Positive
P1218Injector Circuit Cylinder 6 Short To Positive
P1225Injector Circuit Cylinder 1 Short To Ground
P1226Injector Circuit Cylinder 2 Short To Ground
P1227Injector Circuit Cylinder 3 Short To Ground
P1228Injector Circuit Cylinder 4 Short To Ground
P1229Injector Circuit Cylinder 5 Short To Ground
P1230Injector Circuit Cylinder 6 Short To Ground
P1237Injector Circuit Open Cylinder 1
P1238Injector Circuit Open Cylinder 2
P1239Injector Circuit Open Cylinder 3
P1240Injector Circuit Open Cylinder 4
P1241Injector Circuit Open Cylinder 5
P1242Injector Circuit Open Cylinder 6
P1245Needle Lift Sensor Short To Ground
P1246Needle Lift Implausible Signal
P1247Needle Lift Sensor Open/Short To Positive
P1248Start Of Cold Start Injector Control Difference
P1251Start Of Cold Start Injector Short To Positive
P1252Start Of Cold Start Injector Open/Short To Ground
P1255Engine Coolant Temperature Sensor Short To Ground
P1256Engine Coolant Temperature Sensor Open/Short To Positive P1300Misfire Detected, Fuel Level Too Low
P1250Fuel Level Too Low P1325Cyl. 1 Knock Control Limit Attained
P1326Cyl. 2 Knock Control Limit Attained
P1327Cyl. 3 Knock Control Limit Attained
P1328Cyl. 4 Knock Control Limit Attained
P1329Cyl. 5 Knock Control Limit Attained
P1330Cyl. 6 Knock Control Limit Attained
P1336Engine Torque Adaption At Limit
P1337CMP Sensor Bank 1 Short To Ground
P1338CMP Sensor Bank 1 Open Circuit Or Short To Positive P1340CKP/CMP Sensor Signals Out Of Sequence
P1341Ignition Coil Output Stage 1 Short To Ground
P1343Ignition Coil Output Stage 2 Short To Ground
P1345Ignition Coil Output Stage 3 Short To Ground
P1354Modulating Piston Displacement Sensor Electrical Circuit Malfunction
P1386Internal Control Module Knock Control Error
P1387Control Unit Internal Altitude Sensor
P1391CMP Sensor Bank 2 Short To Ground
P1392CMP Sensor Bank 2 Open Circuit/Short To Positive
P1393Ignition Coil Power Output Stage 1 Malfunction
P1394Ignition Coil Power Output Stage 2 Malfunction
P1395Ignition Coil Power Output Stage 3 Malfunction
P1401EGR Valve Power Stage Short To Ground
P1402EGR Vacuum Regulator Solenoid Valve Short To Positive P1403EGR System Control Difference
P1407EGR Temperature Sensor Signal Too Low
P1408EGR Temperature Sensor Signal Too High
P1410Tank Ventilation Valve Circuit Short To B+ P1420Secondary Air Injection Control Module Electrical Malfunction P1421Secondary Air Injection Valve Circuit Short To Ground P1422Secondary Air Injection Valve Circuit Short To B+ P1424Secondary Air Injection System Bank 1 Leak Detected P1425Tank Ventilation Valve Short To Ground P1426Tank Ventilation Valve Open Circuit P1432Secondary Air Injection Valve Open P1433Secondary Air Injection Pump Relay Circuit Open P1434Secondary Air Injection Pump Relay Circuit Short To Positive P1435Secondary Air Injection Pump Relay Circuit Short To Ground P1436Secondary Air Injection Pump Relay Circuit Electrical Malfunction P1440EGR Valve Power Stage Open P1441EGR Vacuum Regulator Solenoid Valve Open/Short To Ground P1450Secondary Air Injection System Circuit Short To Positive P1451Secondary Air Injection Circuit Short To Ground P1452Secondary Air Injection System Circuit Open P1471EVAP Control System LDP Circuit Short to Positive P1472EVAP Control System LDP Circuit Short To Ground P1473EVAP Control System LDP Open Circuit P1475EVAP Control System LDP Malfunction/Signal Circuit Open P1476EVAP Control System LDP Malfunction/Insufficient Vacuum P1477EVAP Control System LDP Malfunction P1478EVAP Control System LDP Clamped Tube Detected P1500Fuel Pump Relay Electrical Circuit Malfunction P1501Fuel Pump Relay Circuit Short To Ground P1502Fuel Pump Relay Circuit Short To Positive P1505Closed Throttle Position Does Not Close/Open Circuit P1506Closed Throttle Position Switch Does Not Open./Short To Ground P1512Intake Manifold Changeover Valve Circuit Short To Positive P1515Intake Manifold Changeover Valve Circuit Short To Ground P1516Intake Manifold Changeover Valve Circuit Open P1519Intake Camshaft Control Bank 1 Malfunction P1522Intake Camshaft Control Bank 2 Malfunction P1537Fuel Cut-off Valve Incorrect Function P1538Fuel Cut-off Valve Open/Short To Ground P1539Clutch Pedal Switch Signal Fault P1540VSS Signal Too High P1541Fuel Pump Relay Circuit Open P1542Throttle Actuation Potentiometer Range/Performance P1543Throttle Actuation Potentiometer Signal Too Low P1544Throttle Actuation Potentiometer Signal Too High
P1545Throttle Position Control Malfunction P1546Wastegate Bypass Regulator Valve Short To Positive P1547Wastegate Bypass Regulator Valve Short To Ground P1548Wastegate Bypass Regulator Valve Open P1549Wastegate Bypass Regulator Valve Open/Short To Ground P1550Charge Pressure Control Difference P1555Charge Pressure Upper Limit Exceeded P1556Charge Pressure Negative Deviation P1557Charge Pressure Positive Deviation P1558Throttle Actuator Electrical Malfunction P1559Idle Speed Control Throttle Position Adaption Malfunction P1560Maximum Engine Speed Exceeded P1561Quantity Adjuster Control Difference P1562Quantity Adjuster Upper Stop Value P1563Quantity Adjuster Lower Stop Value P1564Idle Speed Control Throttle Position Low Voltage During Adaption P1565Idle Speed Control Throttle Position Lower Limit Not Obtained P1568Idle Speed Control Throttle Position Mechanical Malfunction P1569Switch For CCS Signal Faulty P1580Throttle Actuator B1 Malfunction P1582Idle Adaptation At Limit P1600Power Supply Terminal No. 15 Low Voltage P1602Power Supply Terminal No. 30 Low Voltage P1603Internal Control Module Self Check P1606Rough Road Spec. Engine Torque ABS-ECU Electrical Malfunction P1611MIL Call-Up Circuit/TCM Short To Ground P1612Engine Control Module Incorrect Coding
P1613MIL Call-Up Circuit Open/Short To Positive P1616Glow Plug Indicator Lamp Short To Positive P1617Glow Plug Indicator Lamp Open/Short To Ground P1618Glow Plug Relay Short To Positive P1619Glow Plug Relay Open/Short To Ground P1624MIL Request Signal Active P1626Data Bus Drive Missing Command From M/T P1630Accelerator Pedal Position Sensor 1 Signal Too Low P1631Accelerator Pedal Position Sensor 1 Signal Too High P1632Accelerator Pedal Position Sensor 1/2 Supply Voltage P1633Accelerator Pedal Position Sensor 2 Signal Too Low P1634Accelerator Pedal Position Sensor 2 Signal Too High P1639Accelerator Pedal Position Sensor 1/2 Range Performance P1640Internal Control Module (EEPROM) Error P1648CAN-Bus System Component Failure P1649Data Bus Powertrain Missing Message From Brake Controller P1676Drive By Wire MIL Circuit Electrical Malfunction P1677Drive By Wire MIL Circuit Short To Positive P1678Drive By Wire MIL Circuit Short To Ground P1679Drive By Wire MIL Circuit Open Circuit P1681Control Module Programming Not Finished P1686Control Unit Error, Programming Error P1690MIL Malfunction P1691MIL Open Circuit P1692MIL Short To Ground P1693MIL Short To Positive P1778Solenoid EV7 Electrical Malfunction P1780Engine Intervention Readable P1851Data Bus Drive Missing Command From ABS P1854Drive Train CAN-Bus Inoperative

Read more at: https://www.obd-codes.com/trouble_codes/volkswagen/
Copyright OBD-Codes.com

Apr 03, 2012 | Volkswagen Passat Cars & Trucks

1 Answer

Had p code 1167 b1 s1 on and off for a couple of days, now ihave misfire code for cylinders 2 4 6 and running very poor as you would know checked plugs and wires ( ok ) ignition wires are mixed on the...


This has nothing to do with the O2 sensor, this is the A/F sensor in the exhaust manifold

DTC P1167: A/F Sensor (Sensor 1) Heater System Malfunction

NOTE: If DTC P1162 is stored at the same time as DTC P1167, troubleshoot DTC P1162 first, then troubleshoot DTC P1167.

Reset the ECM/PCM.
Start the engine. Wait for at least 80 seconds . Is DTC P01167 indicated? YES - Go to step 3. NO - Intermittent failure, system is OK at this time. Check for poor connections or loose wires at C102 (located under the under-hood fuse/relay box), the A/F Sensor relay, the A/F Sensor (Sensor 1), and the ECM/PCM.
Disconnect the A/F Sensor 4P connector, and ECM/PCM connector C (31P).

Connect ECM/PCM connector terminals C14 and C15 to body ground with a jumper wire.

Check for continuity between A/F Sensor (Sensor 1) 4P connector terminal No.1, No.2, and body ground individuality. Is there continuity? YES - Replace the A/F Sensor (Sensor 1). NO - Repair open or short in the wire between the A/F Sensor (Sensor 1) and the ECM/PCM (C14 or C15).

Oct 08, 2011 | Cars & Trucks

1 Answer

What is diagnostic procedures for DTC p0135 & p0141


Oxygen Sensor problems... P0135 (Bank 1, Sensor 1) and P0141 (Bank 1, Sensor 2)

P0135 - Oxygen O2 Sensor Heater Circuit Malfunction (Bank 1, Sensor 1)
This code refers to the front oxygen sensor on Bank 1. The heated circuit in the oxygen sensor decreases time needed to enter closed loop. As the O2 heater reaches operating temperature, the oxygen sensor responds by switching according to oxygen content of the exhaust surrounding it.

The ECM tracks how long it takes for the oxygen sensor to begin switching. It the ECM determines (based on coolant temp) that too much time elapsed before the oxygen sensor began operating properly, it will set P0135.

Symptoms: You will likely notice poor fuel economy the illumination of the MIL.

Causes: A code P0135 may mean that one or more of the following has happened:
O2 Heater element resistance is high
Internal short or open in the heater element
O2 heater circuit wiring high resistance
open or short to ground in the wiring harness

Possible Solutions:
Repair short or open or high resistance in wiring harness or harness connectors
Replace oxygen sensor (cannot repair open or short that occurs internally to sensor)



P0141 - O2 Sensor Heater Circuit Malfunction (Bank 1, Sensor 2)
This code means that the heated circuit in the oxygen sensor on bank 1 decreases time needed to enter closed loop. As the O2 heater reaches operating temperature, the oxygen sensor responds by switching according to oxygen content of the exhaust surrounding it. The ECM tracks how long it takes for the oxygen sensor to begin switching. It the ECM determines (based on coolant temp) that too much time elapsed before the oxygen sensor began operating properly, it will set P0141.

Symptoms: You will likely notice poor fuel economy the illumination of the Check Engine Light.

Causes: A code P0141 may mean that one or more of the following has happened:
open or short to ground in the wiring harness
O2 heater circuit wiring high resistance
O2 heater element resistance is high
Internal short or open in the heater element

Note: Typically a failed catalytic converter does not cause this code. You're more likely to see a P0420 code for a failed converter.

Possible Solutions:
Replace oxygen sensor (cannot repair open or short that occurs internally to sensor)
Repair short or open or high resistance in wiring harness or harness connectors


Hope this helps (remember to rate this answer)..

May 11, 2011 | 2000 Nissan Maxima

1 Answer

What does the code p1166 mean on my 2003 rsx type s


DTC P1166: A/F Sensor (Sensor 1) Heater Circuit Malfunction


  1. Reset the ECM/PCM.
  2. Start the engine.
Is DTC P1166 indicated?

YES - Go to step 3.

NO - Intermittent failure, system is OK at this time. Check for poor connections or loose wires at C101 (located under the right side of the dash), C401 (located under the left side of the dash), C402 (located under under the left side of the dash) the A/F Sensor relay, the A/F Sensor (Sensor 1) and the ECM/PCM.


  1. Check the following fuse:
    • No.14 OPTION (30A) fuse in under-hood fuse/relay box.
    • No.2+B LAF HEATER (20A) fuse in under-dash fuse/relay box.
    • No. 4ACG (10A) in under-dash fuse/relay box.
Are any of the fuses blown?

YES - Repair short in the wire between the A/F Sensor relay and the fuses.

NO - Go to step 4.

94729647

  1. Measure voltage between ECM/PCM connector terminals A1 and A24, 30 seconds after the ignition switch is turned ON (II).
Is there battery voltage?

YES - Update the ECM/PCM if it does not have the latest software, or substitute a known-good ECM/PCM, then recheck. If the symptom/indication goes away with a known-good ECM/PCM, replace the original ECM/PCM.

NO - Go to step 5.

94729648

  1. Measure voltage between ECM/PCM connector terminals A22 and A24.
Is there battery voltage?

YES - Go to step 6.

NO - Go to step 10.


  1. Turn the ignition switch OFF.
  2. Disconnect ECM/PCM connector E (31P).
  3. Turn the ignition switch ON (II).
94729649

  1. Connect ECM/PCM connector terminal E8 to body ground with a jumper wire, then measure voltage between ECM/PCM connector terminals A1 and A24.
Is there battery voltage?

YES - Update the ECM/PCM if it does not have the latest software, or substitute a known-good ECM/PCM, then recheck. If the symptom/indication goes away with a known-good ECM/PCM, replace the original ECM/PCM.

NO - Repair open or short in the wire between the A/F Sensor (Sensor 1) and ECM/PCM (A1).


  1. Turn the ignition switch OFF.
  2. Disconnect the ECM/PCM connector A (31P) and the A/F Sensor (Sensor 1) 4P connector.
94729650

  1. Check for continuity between the A/F Sensor (Sensor 1) 4P connector terminal No.3 and body ground.
Is there continuity?

YES - Repair short in the wire between the A/F Sensor relay, A/F Sensor (Sensor 1) and ECM/PCM (A22).

NO - Go to step 13.


  1. Turn the ignition switch ON (II).
94729651

  1. Measure voltage between ECM/PCM connector terminals E8 and A24.
Is there battery voltage?

YES - Repair open in the wire between the ECM/PCM (A22) and the A/F Sensor (Sensor 1).

NO - Go to step 15.


  1. Check for continuity in the wires between the A/F Sensor and the fuses.
Is there continuity?

YES - The wires are OK. Replace the A/F Sensor relay.

NO Repair open in the wire between the A/F Sensor relay and the fuses.

Mar 17, 2011 | Acura RSX Cars & Trucks

1 Answer

CODE PO155 BANK2 SENSOR 1 WHERE IS THIS SENSOR LOCATED?


A code P0155 may mean that one or more of the following has happened:
* O2 Heater element resistance is high
* Internal short or open in the heater element
* O2 heater circuit wiring high resistance
* open or short to ground in the wiring harness

Possible Solutions:
* Repair short or open or high resistance in wiring harness or harness connectors
* Replace oxygen sensor (cannot repair open or short that occurs internally to sensor)


Oxygen sensors are always numbered like this:
Bank 1 sensor 1
Bank 2 sensor 1
Bank 1 sensor 2
Bank 2 sensor 2

Some manufacturers use a kind of shorthand that reads different, but means the same thing:
Sensor 1/1 or O2s 1/1
Sensor 2/1 or O2s 2/1
Sensor 1/2 or O2s 1/2
Sensor 2/2 or O2s 2/2

Bank 1 is always the side of the engine where cylinder number 1 is located and, of coarse, Bank 2 is the opposite side.
On a 4 cylinder engine, there is only 1 bank and it is always referred to as Bank 1.

Sensor 1 is always the upstream sensor (The one located BEFORE the catalytic converter)
Sensor 2 is always the downstream sensor (the one that is located AFTER the catalytic converter.

Hope helps (remember to rate this).

Oct 02, 2010 | 2002 Mitsubishi Montero

2 Answers

I have a 2001 kia rio, check engine light came on. stopped at Auto Zone an they tested it. Their machine said it was CODE P1166. what is this part we need?


1166 - AF sensor 1 heater circuit malfunction

Your top O2 sensor (the LAF sensor) may be unplugged or the wire may be damaged, or it may be dead.

Sep 02, 2010 | 2001 Kia Rio

1 Answer

2001 dodge durango 4.7liter 4x4 i replaced front o2 sensor,rear 02 sensor,ground wire to exhaust and the engine light keeping coding saying (o2 sensor heater curcuit malfunction bank 1 sensor 2). car runs...


bank 1 sensor 2 is the left downstream sensor (1/2) is located in the exhaust downpipe just after the mini-catalytic convertor, and before the main catalytic convertor. Now the meaning of this is that your not getting any 12+/12- heating on sensor, which means voltage is supplied to heat sensor up. You have a O2 sensor heater relay, but not getting problem with 2/2 sensor tells me you need to check/inspect the wiring for 1/2 sensor, open wiring for 1/2 sensor and inspect

Feb 07, 2010 | 2001 Dodge Durango

2 Answers

P0031, ho25circuit low, bank 1 sensor 1. sft b1 -3.91, ltft b1 .78, stft b2 -3.91, ltft b2 3.91. R&R ox sensor or what


Hello,
P0031 - Bank 1 Heated Oxygen Sensor No. 1 Heater Circuit - Low Voltage. That is what this code means.
DTC P0031 is set when Bank 1 HO2S No.1 heater current is less then .09 amps, or potential difference between heater positive and negative terminals is more then 13.99 volts while HO2S heater is on. MIL (The engine light) is illuminated when Engine Control Module (ECM) detects malfunction during 2 consecutive drive cycles.
Possible Causes are: - Bank 1 HO2S No. 1 heater circuit malfunction - Bank 1 HO2S No. 1 heater malfunction - ECM malfunction - HO2S heater relay

DTC Confirmation Test (Advanced/Intermediate Users): Ensure intake air tempature is 18f (-8c) or more, engine coolant tempature is 18-230f (-8-110c) and vehicle is at an altitude of 8000 feet or below, and barometric pressure is 75 kPa or more. Turn ignition off, connect scan tool and turn ignotion on. Using scan tool, clear DTCs. Start engine and run at idle speed for 5 minutes. Using scan tool check for current or pending DTC P0031.

Diagnosis & Repair Procedure (Advanced/Intermediate Users): 1. If engine system check has been performed, go to the next step. If engine system check has not been performed, do the system check.
2. Turn ignition off. Disconnect Bank 1 HO2S No. 1 4-pin harness connector. Bank 1 HO2S No. 1 is located in the left exhause pipe before catalytic convertor. Measure resistance between Bank 1 HO2S No. 1 pigtail connector terminal No. 3 (Green wire) and No. 4 (Blue wire). Resistance should be 5.0-6.4 ohms at 68f (20c). If resistance is as specified, go to next step. If resistence is not as specified, replace HO2S. After repair repeat DTC Confirmation Test (Above).
3. Disconnect HO2S heater relay. HO2S heater relay is located on the left fender well. Turn ignition On. Measure voltage between ground and HO2S heater relay socket cavity No. 3 (Black/White wire). Also measure voltage between ground and HO2S heater relay socket cavity No. 1 (Blue/White wire). If voltage readings at both measurements is 10-14 voltes, go to step 5. If voltage readings are not as specified go to next step.
4. Check for blown HO2S (15-amp) or IG COIL (20-amp) fuses. Fufses are located in the underhood fuse and relay boxc. If fuses are okay, check for open or short it to ground in Black/White wire between IG COIL fuse HO2S heater relay. If problem is found repair as necessary. After repair repeat DTC Confirmation Test (Above).
5. Turn Ignition off. Install HO2S heater relay. Dicsonnect ECM 30-pin harness connector C51-2. ECM is located under instrument panel, under glove box. Measure voltage between ground and ECM harness connector C51-2 terminal No. 4 (Green wire). If voltage reading is 10-14 volts, subsitute a known-good ECM, and repeat DTC Confirmation Test (Above). If DTC does not reset, testing is complete. If voltage readings are not specified, go to next step.
6. Check for short to ground in Green wire between Bank 1 HO2S No. 1 and ECM. If no problem with wiring is found, replace HO2S heater relay. If problem persists after repairs, subsitute a known-good ECM and repeat DTC Confirmation Test (Above).

I hope this helps and is what your looking for. Best of luck.

Nov 21, 2009 | 2003 Suzuki XL-7

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...