Question about 2006 Chrysler 300

1 Answer

On the Chrysler 300, 06. The old pump and the new pump comes on for 2 to 5 sec then stops running. Engine sounds like its. Not getting any gas. Trying to locate the fuel release VAL under Hood.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Expert
  • 62 Answers

The fuel pump normally only comes on for a second unless the car starts and is running, if the car starts and the pump only runs for a few seconds, then there is a problem with the engine signal to the ecm, ie its not telling the computer that it is running. I dont believe there is a schrader valve on those fuel lines, if there is, chrysler probably put it underneath the intake plenum. If the car will not start, but you hear the fuel pump kick on and off, it could have a clogged fuel filter, or injectors, or even bad connections going to the injectors. They normally are all switched via the ground wire for each injector, so if they are not cycling it could be a bad ecm, or bad connection somewhere in the wiring harness

Posted on Jul 10, 2016

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

kdreis

  • 12 Answers

SOURCE: Fuel pump relay

Fuel pump in back in the gas tank.

Posted on Jan 30, 2009

Anonymous

  • 1 Answer

SOURCE: installed new fuel pump and it still wont start.

I had the same problem. I had to put in a 22 gage fusable link. It had burned out. I first thought it was the fuel pump.

Posted on Jun 10, 2009

Anonymous

  • 34 Answers

SOURCE: ticking, sounds like lifters.

with engine running try using long screwdriver on valve cover & listen through handle to help pinpoint noise

Posted on Jun 20, 2009

Anonymous

  • 237 Answers

SOURCE: 1998 gmc 2500 sle 5.7 wont stay running

this is in fact the right answer check the oil guage in the truck it should read about 375.

Posted on Dec 15, 2009

bnjmnolivas

Ben Olivas

  • 10 Answers

SOURCE: 1988 Buick Century, not getting gas

by pass relay to see what happens.

Posted on Apr 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Car has been sitting Need to run.


The old gas will cause hard starting for sure as it is 15 years old but if you don't have very much in the tank you can mix in some new gas.

Oct 23, 2015 | 2000 Chrysler LHS

1 Answer

Engine quit, stopped running, engine light came on


Did you check the asd relay ? Does the fuel pump run if you jumper the pump relay ?
Does the engine have normal compression, spark, and fuel pressure ?

Feb 19, 2014 | Chrysler PT Cruiser Cars & Trucks

1 Answer

Starts but stops in a few sec


If it stops like running out of gas, you will need to check the fuel pump circuit for power. It has power for 5 seconds thru a relay then is supposed to run only if the engine has oil pressure.

Jun 23, 2012 | 2005 Chrysler Town & Country

1 Answer

Cant start 94 cadillac elderado


Check fuel pump pressure and fuel pump regulator. It sounds like you are not getting fuel into the system and if you are you are not getting enough fuel into the system

Jan 02, 2010 | 1994 Cadillac Eldorado

2 Answers

I can't pump gas in my 04 GMC Envoy, it keeps shutting off


run the fault codes
indicates a EVAP venting problem

Oct 24, 2017 | 1997 Toyota Camry

1 Answer

Engine oli pressure & car stopped running


Do you have the car at your house? Check fuses and relays. Some are tied in with the ignition system. For the oil level check it with puting an actual pressure guage on it. The sending unit for your oil psi might be worn out and not sending the correct reading. Check and see if you are getting fuel and another way to check the fuel pump is take the gas cap off, have someone turn the key on like they were going to start the car and you should be able to hear a humm coming from the gas tank this means the pump is okay. If you have the humm but no fuel comming up to intake then check the fuel filter, if it hasn't been changed in awhile it might be clogged.
One more question ..... Do you have power right now? Do your lights and everything else turn on?

Jan 03, 2009 | 1987 Chrysler New Yorker

3 Answers

88 chevy pickup 5.0l


first, turn the key on, but do not crank the engine. do you hear the fuel pump run for about 2 seconds?

Jul 03, 2008 | 1988 Chevrolet K1500

Not finding what you are looking for?
2006 Chrysler 300 Logo

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...