I need the cylinder head torque settings for a hyundai getz 1.6 16 valve double overhead cam Engine cod G4ED

1. First, tighten all the bolts to 25 Nm (18 lb-ft).
2. Tighten all the bolts to 50 Nm (37 lb-ft) in sequence, starting from the center and working outward.
3. Tighten all the bolts to 70 Nm (52 lb-ft) in sequence again, starting from the center and working outward.
4. Finally, tighten all the bolts an additional 90 degrees in sequence again.

Please note that it's important to follow the correct torque sequence and to use a torque wrench to ensure that the bolts are tightened to the correct specifications. It's also recommended to replace the head bolts with new ones to ensure proper torque and head gasket sealing.

The torque specification for the rocker shafts on the 2001 Hyundai Accent with the 1.5L single overhead cam engine is 18-20 lb-ft. The proper torque sequence is as follows:

1. Tighten the bolts to 8 lb-ft in a crosswise pattern.
2. Increase the torque to 15 lb-ft, again in a crosswise pattern.
3. Finally, tighten the bolts to the full torque of 18-20 lb-ft, again in a crosswise pattern.

Make sure to use a torque wrench and follow the sequence carefully to ensure proper tightening and prevent damage.

Question edited for dreadful spelling :>D

The search query for this is 'year make model (part you want) torque settings

Here is the cylinder head torque settings

https://www.google.com/search?q=hyundai+getz+1.4+cylinder+head+torque+settings

..

you make answering very difficult because you do not give specific information
the excel comes in ser X1 (1985-1989), X2(1990-1995), X3(1994-2000) depending on the year
the engine capacity is missing so 1.3 LT engines are single over head cam and 1.6LT engines are double head cam
to make matters worse
the 1.3LT ( engine family G4EH) is single over head cam
the 1.5 Lt ( G4EK is a SOHC
the 1.5LT ( G4FK) is a DOHC
and the 1.6LT( G4ED) is a DOHC
Now you can see the difficulty in giving you a definitive answer
Why don't you simply ring the shop and ask them to check for you

See the settings here:
http://www.autozmagz.com/search/hyundai+getz+cylinder+head+bolt+torque+settings

Hi, Acording to autodata the following applies.
hyundia matrix 1.6 01-09 engine g4ed
stage 1 +30nm
stage 2 +90 degrees
stage 3 slacken 360 degrees
stage 4 +30nm
stage 5 +90 degrees

Jon

Follow these steps to adjust to the recommended torque:
1. cylinder head-30-35 nm + 30-35 + 65deg + 65deg.
2. mains-30nm +65deg
3. big ends- 1 - 26nm 2 - 52NM
4. fly-wheel -130nm
5. cam-sprocket - 100-120
6. crank-pulley - 170-180
7. cam caps -15nm

Torque settings for hyundai accent 1.3

Bore × stroke 81.00 mm × 86.40 mm 3.19 in × 3.4 in Cylinders s-4 SOHC Single overhead camshaft DOHC Double overhead camshaft OHV Overhead valves TS Two stroke SV Side valves

Sl

Sleeve valves

oise

Overhead inlet side exhaust

5 valves per cylinder
20 valves in total
compression ratio
9.30:1 fuel system
MPFi Maximum power 150.1 PS (148.0 bhp) (110.4 kW)
@ 5700 rpm Specific output 83.1 bhp/litre
1.36 bhp/cu in Maximum torque 210.0 Nm (155 ft·lb) (21.4 kgm)
@ 1750 rpm bmep 1481.7 kPa (214.9 psi) Specific torque 117.91 Nm/litre