There is no such thing , What code do you have if any ? There is a purge solenoid for the EVAP system ! evaporative emission system. An there is a vent solenoid , a fuel tank pressure (FTP) sensor.
The evaporative emission (EVAP) control system limits fuel vapors from escaping into the atmosphere. Fuel tank vapors are allowed to move from the fuel tank, due to pressure in the tank, through the vapor pipe, into the EVAP canister. Carbon in the canister absorbs and stores the fuel vapors. Excess pressure is vented through the vent line and EVAP vent valve to atmosphere. The EVAP canister stores the fuel vapors until the engine is able to use them. At an appropriate time, the control module will command the EVAP purge valve ON, open, allowing engine vacuum to be applied to the EVAP canister. With the EVAP vent valve OFF, open, fresh air will be drawn through the valve and vent line to the EVAP canister. Fresh air is drawn through the canister, pulling fuel vapors from the carbon. The air/fuel vapor mixture continues through the EVAP purge pipe and EVAP purge valve into the intake manifold to be consumed during normal combustion. The control module uses several tests to determine if the EVAP system is leaking.
P0440 Evaporative emission (EVAP) system - malfunction
Possible causes: Hose connection(s), intake leak, EVAP canister purge valve
P0441 Evaporative emission (EVAP) system - incorrect flow detected
Possible causes: Hose connection(s), intake leak, EVAP canister purge valve
P0442 Evaporative emission (EVAP) system - small leak detected
Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve
P0443 Evaporative emission (EVAP) canister purge valve - circuit malfunction
Possible causes: Wiring, EVAP canister purge valve, ECM
P0444 Evaporative emission (EVAP) canister purge valve -open circuit
Possible causes: Wiring open circuit, EVAP canister purge valve, ECM
P0445 Evaporative emission (EVAP) canister purge valve -short circuit
Possible causes: Wiring short circuit, EVAP canister purge valve, ECM
P0450 Evaporative emission (EVAP) pressure sensor - circuit malfunction
Possible causes: Wiring, EVAP pressure sensor, ECM
P0455 Evaporative emission (EVAP) system - large leak detected
Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve
P0456 Evaporative emission system - very small leak detected
Possible causes: Mechanical fault, hose connection(s), EVAP pressure "sensor
P0457 Evaporative emission system - leak detected (fuel cap loose/off)
Possible causes: Mechanical fault, hose connection(s), EVAP pressure sensor
P0458 Evaporative emission system, purge control valve -circuit low
Possible causes: Wiring short to earth, EVAP valve
P0459 Evaporative emission system, purge control valve -circuit high
Possible causes: Wiring short to positive, EVAP valve
Evaporative Emission Purge Solenoid
Description & Operation
The duty cycle EVAP canister purge solenoid (DCP) regulates the rate of vapor flow from the EVAP canister to the intake manifold. The Powertrain Control Module (PCM) operates the solenoid.
During the cold start warm-up period and the hot start time delay, the PCM does not energize the solenoid. When de-energized, no vapors are purged. The PCM de-energizes the solenoid during open loop operation.
The engine enters closed loop operation after it reaches a specified temperature and the time delay ends. During closed loop operation, the PCM cycles (energizes and de-energizes) the solenoid 5 or 10 times per second, depending upon operating conditions. The PCM varies the vapor flow rate by changing solenoid pulse width. Pulse width is the amount of time that the solenoid is energized. The PCM adjusts solenoid pulse width based on engine operating condition.
Removal & Installation
The duty cycle evaporative (EVAP) canister purge solenoid is located in the engine compartment near the brake master cylinder.
719 views
Usually answered in minutes!
×