The p0300--p0301-p0302=p0303 are misfire codes and can mean needs tune up or wiring problem and p0171 is system to lean bank 1 with this code if you correct it will probably correct the misfire codes your receiving
http://www.obd-codes.com/p0171 Fixing Hesitating Car P0171 Code YouTube P0171 System Too Lean Bank 1
SOURCE: 98 E-250 Rough Idle; codes p0156,p1131,p1151,p0301,p0171,p0174+
po301 thru po306 all misfire codes cylinder 1-6 remove plugs and replace them..... set the plug gap first
i suggest u replace the wires also if they never been replaced all these misfire codes can set the others and one is for the oxygen sensor ( 02s or HO2S) CIRCUT MALFUNCTION do u know how to check wireing systems
do the tune up plugs (set gap) .052-.056 change the fuel filter also. clear the codes hows it run
this info is for 98 E-250 4.2Litre
what engine do u have 4.2L or 4.6L i know it is a v-6 by the codes
SOURCE: 12 codes; 90174, p0171, p0175,p0300,p0301, p0302,
I would be very hesitant about just going in and replacing parts/sensors, especially those diagnosed from Electronic Control Module (ECM) Diagnostic Trouble codes (DTC's) alone, as quite often when multiple codes are present, they are often related to a songle malfunction/failure (Such as coil codes, and O2, rich/lean codes, etc...) - A p0171 and 0174 code is not indicative of a faulty MAF sensor - it is a code set when a lean condition is detected within the vehicle's exhaust...often caused by vacuum leaks, EGR valve malfunctions, BAC/IAC ( Bypass/Idle air control) valve malfunction, DPFE sensor malfunction, or the MAF "hot wire" is dirty, and can be cleaned with the correct cleaner, but instead of replacing a $250 MAF sensor; only to later find out that if you had the vehicle repaired by a trained technician, a $3 vacuum hose and a $50 ignition coil had initiated the multiple DTC's - So, sometimes it does pay to use a trained technician; especially with so many codes present - Like I said - If I were going to do the work myself, I would erase all the codes (Disconnect battery cable for about 10 mins - this will also erase the block/learn ECM settings and it may search for idle for a bit, but will straighten out with time - reconnect battery and start the car - then after the light re-illuminates, re-pull the codes, and most importantly test the sensors/parts indicated by the DTC's before replacing anything - that is if you want to fix it the most cost effective way possible, but, if you have plenty of money to waste you could always just go replace whatever the DTC's tell you is out of specifications, regardless of the cause...this might fix it, but may not as well - if you got lots of money and feel lucky it's the way to go - if not, test those parts and sensor before replacing them - there is a process for testing each of them....Thanks
Testimonial: "Thanks you so very much. The car was shaking and making a knocking sound and running very poorly and now the engine is locked I had in towed home."
SOURCE: 2003 mercedes Benz C240 codes P0300, P0301, P0302
P0300 Random Misfire Detected
P0301 Cylinder 1 Misfire Detected
P0302 Cylinder 2 Misfire Detected
P0303 Cylinder 3 Misfire Detected
according to this fault codes first mark ignition coils
3 ---------------- 6
2 ---------------- 5
1 ---------------- 4
RB-------------LB
this right banks and left bank, please remove Ignition coils with lids and spark plugs from right bank and swap with left bank, if fault code change as
P 0304 Cylinder 4 Misfire Detected
P 0305 Cylinder 5 Misfire Detected
P 0306 Cylinder 6 Misfire Detected
You can Identify it's a faulty ignition system then next swap ignition lids from ignition coils be careful each coils have two lids one short and other long bit deference and when you remove and fix it to the car keep in mind correct order because each coil two different fire for two spark plugs don't mix up, if you mix it can create the fault code.if you detect any fault ignition coils or spark plugs or lids replace that and also whether god or bad recommend to replace spark plugs, find the right that's most important thing, if this way couldn't found the any ignition fault next step is check fuel presser, when the engine running fuel presser must be around 4.5 bar without engine running must be 4 to 6 bar if the fuel presser too low need to check two different things one is fuel pump other is fuel injectors, in this case you can swap injectors from right bank to left bank and find is the injectors leaking, if not leaking faulty fuel pump.is this information helped you? if yes please leave a comment,
SOURCE: getting codes P0341, p0300, p0301, p0302, p0303
P0300 is multiple misfire. The corrective action for this code would be to test your fuel pressure and the injectors. P0301, P0302, P0303 is saying in certain cylinders there is a misfire. There are two different engines so I wasn't sure which one you have and couldn't give you the correct testing procedures for the coils. P0341 is saying the camshaft position sensor readings are bad. Again I am unable to give you the correct tests to check this due to not knowing your engine size. Feel free to email me at [email protected] with detailed information about your vehicle and I will be happy to email you the testing procedures to narrow down the problem and help you solve it.
SOURCE: P0300 P0301 P0302 P0303 P0304
Hi friend ,maybe this PDF can help you to solve the problem, Diagnostic Trouble Code Table ,hope can help you .
1,253 views
Usually answered in minutes!
×