How to changed wiper blade for 2007 Acura RL

On the WEB:

Front Wiper Blade Change Jaguar XJ8 (2004-2009) - 2008 ...

www.carcarekiosk.com/...Jaguar.../windshield_wiper_blade.../replace_wi...
Free video on how to replace the front windshield wiper blades in a 2008 Jaguar XJ8 L 4.2L V8. Complete instructions for changing the front wiper windshield ...

It is located in the engine compartment on the drivers side of the vehicle under the windshield wiper cleaner tank directly behind the headlamp.

TO CHANGE WIPER BLADES ALL YOU DO PRESS ON THE TAB AND PUSH THE BLADE ASSEMBLY OUT OF THE HOOK END TO REMOVE IT.IF YOU HAVE DIFFICULT TIME REMOVING WIPER BLADES.THE AUTO PARTS STORE SALES PERSON WHERE YOU PURCHASE BLADES WILL INSTALL THEM FREE FOR YOU.

wiper gears may be broken, got to junk yard and buy motor and gear assembly for windshield wipers, should only take an hour to change out.

YOUR WIPER MOTOR COULD HAVE BINDING LINKAGE AND PIVOTS.TRY LUBRICATE THEM WITH WD40.TRY NOT TO GET ANY ON WINDSHIELD.IF THIS DONT WORK WIPER MOTOR COULD BE FAULTY.

How to Replace Wiper Blades Guide (Typical):
Potential tools needed to replace wiper blades:

• Flat blade screwdriver (small)
• Small nosed pliers
• Latex or vinyl gloves
• Safety goggles

To replace wiper blades theactual action of replacing the blade is no big deal, it's the locationof the blade down below the hood that can make it difficult though.Sometimes it helps to open the hood to gain access to the wiper blades.Other times it is helpful if the wiper blade is somewhere in the motionline of wiper action. The trick is to get the wiper to stop somewherein the wiper arc. Turn the wipers to the on position and allow thewipers to start, and then shut the key off when the wiper has arrivedin a desirable position on the windshield. To replace your wiper bladesplease follow the step by step instruction below. Also, watch the How to replace wiper blades video below to gain additional information. The method in which the wiper blades are attached will vary slightly.

• Step 1: With the hood closed, turn the wiperson, when the wipers are in the middle of their arc turn the key to theoff position. (Note: if this can't be done because of wiper conditionand you want to avoid scratching the windshield please open your hoodto gain access)
• Step 2: Locate the mounting clips at the top pivot on the wiper blade
• Step 3: Release the clip and remove the wiper arm
• Step 4: Match the size of the old blade against the new blade to ensure proper fit and operation
• Step 5: Reinstall the new wiper blade and recheck wiper operation

Common Problems:

• Make sure the wiper blades are the same size as the original blades.
• When replacing wiper blades not getting the blade onthe mounting pin completely allowing the wiper arm to become dislodgedand possibly causing damage to the windshield.
• Using wiper blades after the blade has failed permanently damaging the windshield by craving scratches in the wiper arc.
• Wiper blade can create a chattering noise when theblade is not properly balanced allowing the blade to "flop" back andforth as the wiper direction changes.

I hope help you with this (remember rated this help) Good luck.

How to Replace Wiper Blades Guide:
Potential tools needed to replace wiper blades:

• Flat blade screwdriver (small)
• Small nosed pliers
• Latex or vinyl gloves
• Safety goggles

To replace wiper blades the actual action of replacing the blade is no big deal, it's the location of the blade down below the hood that can make it difficult though. Sometimes it helps to open the hood to gain access to the wiper blades. Other times it is helpful if the wiper blade is somewhere in the motion line of wiper action. The trick is to get the wiper to stop somewhere in the wiper arc. Turn the wipers to the on position and allow the wipers to start, and then shut the key off when the wiper has arrived in a desirable position on the windshield. To replace your wiper blades please follow the step by step instruction below. Also, watch the How to replace wiper blades video below to gain additional information. The method in which the wiper blades are attached will vary slightly.

• Step 1: With the hood closed, turn the wipers on, when the wipers are in the middle of their arc turn the key to the off position. (Note: if this can't be done because of wiper condition and you want to avoid scratching the windshield please open your hood to gain access)
• Step 2: Locate the mounting clips at the top pivot on the wiper blade
• Step 3: Release the clip and remove the wiper arm
• Step 4: Match the size of the old blade against the new blade to ensure proper fit and operation
• Step 5: Reinstall the new wiper blade and recheck wiper operation

Common Problems:

• Make sure the wiper blades are the same size as the original blades.
• When replacing wiper blades not getting the blade on the mounting pin completely allowing the wiper arm to become dislodged and possibly causing damage to the windshield.
• Using wiper blades after the blade has failed permanently damaging the windshield by craving scratches in the wiper arc.
• Wiper blade can create a chattering noise when the blade is not properly balanced allowing the blade to "flop" back and forth as the wiper direction changes.

I hope help you with this (remember rated this help) Good luck.

it usly the ground curcit in the wiper motor

if they are still the factory wipers, pull the black rubber inserts out, remove the 2 metal peice from the side of the rubber insert, install the metal into the new inserts. slide the insert into the blade. repeat for other side. i recommed that you use factory parts.