Do you know if your door locks are module controlled or non module controlled ?
Locks, Latches and Entry Systems - Module Controlled
Principles Of Operation
CAUTION: Do not use a key, pencil or any other hard object to press the keyless entry keypad buttons. These objects may damage the keyless entry keypad buttons.
NOTE: The remote transmitter will not operate with the transmission in REVERSE or DRIVE.
NOTE: Upon installation of a new driver door module (DDM), the module must be reconfigured. Refer to Section 418-01 .
The DDM receives inputs from the digital transmission range (TR) sensor, ignition switch, brake switch, door lock control switches, lighting control module (LCM), keyless entry keypad and remote transmitter. The DDM outputs consists of keyless entry keypad illumination, door lock actuators, luggage compartment lid release solenoid, and LCM.
For DDM removal and installation information, refer to Section 419-10 .
Inspection and Verification
WARNING: If equipped with fire suppression system, refer to Section 419-03 for important safety warnings.
NOTE: Before starting electrical diagnosis, check for mechanical binds by manually operating the door locks. Operate lock system several times from each switch while observing the operation of all door locks. Be sure battery is fully charged.
- Verify the customer concern.
- Visually inspect for obvious signs of mechanical and electrical damage.
-
Visual Inspection Chart
Mechanical
Electrical
- Battery junction box (BJB) fuse 8 (20A)
- Central junction box (CJB) fuse(s):
- 10 (5A)
- 18 (10A)
- 25 (10A)
- Circuitry
- Connectors
- Door lock actuator
- Door lock control switch
- Keyless entry keypad
- Luggage compartment lid release switch
- Luggage compartment lid release solenoid
- If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.
- If the cause is not visually evident, connect the diagnostic tool to the data link connector and select the vehicle to be tested from the diagnostic tool menu. If the diagnostic tool does not communicate with the vehicle:
- check that the program card is correctly installed.
- check the connections to the vehicle.
- check the ignition switch position.
- If the diagnostic tool still does not communicate with the vehicle, refer to the diagnostic tool operating manual.
- Carry out the diagnostic tool data link test. If diagnostic tool responds with:
- SCP or ISO circuit fault; all electronic control units no response/not equipped, refer to Section 419-10 .
- No response/not equipped for the DDM, refer to Section 419-10 .
- No response/not equipped for the LCM, refer to Section 419-10 .
- System passed, retrieve and record the continuous diagnostic trouble codes (DTCs), erase the continuous DTCs and carry out self-test diagnostics for the DDM and LCM.
- If the DTCs retrieved are related to the concern, go to the Driver Door Module (DDM) Diagnostic Trouble Code (DTC) Index or Lighting Control Module (LCM) Diagnostic Trouble Code (DTC) Index to continue diagnostics.
- If no DTCs related to the concern are retrieved, GO to Symptom Chart .
Drive Door Module (DDM) Diagnostic Trouble Code (DTC) Index
DTC
Description
Source
Action
B1352
Ignition Key In Circuit Failure
DDM
Go To Pinpoint Test H .
B1396
Door Lock Circuit Short To Battery
DDM
Go To Pinpoint Test C .
B1526
Keyless Entry Keypad Circuit Short To Ground
DDM
Go To Pinpoint Test E .
B1553
Luggage Compartment Lid Release Circuit Short To Ground
DDM
Go To Pinpoint Test B .
B1751
Park/Neutral Switch Circuit Short To Battery
DDM
Go To Pinpoint Test L .
B2425
Remote Keyless Entry Out Of Synchronization
DDM
Go To Pinpoint Test M .
Lighting Control Module (LCM) Diagnostic Trouble Code (DTC) Index
DTC
Description
Source
Action
B1300
Door Lock Circuit Failure
LCM
Go To Pinpoint Test N .
B1310
Door Unlock Circuit Failure
LCM
Go To Pinpoint Test N .
B1396
Door Lock Circuit Short To Battery
LCM
Go To Pinpoint Test N .
B1397
Door Unlock Circuit Short To Battery
LCM
Go To Pinpoint Test N .
B1677
Alarm Panic Input Circuit Failure
LCM
Go To Pinpoint Test J .
B1679
Alarm Panic Input Circuit Short To Battery
LCM
Go To Pinpoint Test J .
NOTE: For a complete list of DDM and LCM DTCs, refer to Section 419-10 .
- ????????????? Do you have a professional scan tool ?
??
×