WHERE IS THE CRANKSHFT POSITION CORRELATION BANK 1 SENSOR A IS LOCATOR ON A MERCEDE BENZ 2006 E 350?

cut off = engine stalls p0016(vvt failures) did you look this up first? in a real kia book?
spectra not spectra5
no engine size told. hummmm, 2.0L Automatic?
autozoned parts are junk, china cloned parts are.
so guessing and adding bad parts gets you where? double bad now.

BOOK words to follow

Trouble Code: P0016 (2.0L L4 VIN - Auto)
Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)and read this.
The CVVT (Continuously Variable Valve Timing) system is installed to the chain sprocket of the intake camshaft. This system controls the intake camshaft to provide the optimal valve timing. The PCM controls the Oil Control Valve(OCV), based on the signals output from mass air flow, throttle position and engine coolant temperature. The CVVT controller regulates the intake camshaft angle using oil pressure through the OCV. PCM monitors timing misalignment while no active faults are present and fully warmed up engine oil at idle. If the timing is misaligned PCM determines that a fault exists and a DTC is stored. Possible Causes:

• * Oil level, pressure and condition
• * OCV
• * CVVT
• * Timing mark alignment

note their words, 4 thing wrong, here, VVT is bad.

cam shaft sensor error is
Trouble Code: P0340 (2.0L L4 VIN - Auto)
Camshaft Position Sensor Circuit Malfunction and you never got that code,

You need to get a Good Mechanic to look at this as there are several issues hear that don't make sense.
P0016 = Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor A
P0055 = HO2S Heater Resistance Bank 1 Sensor 3
P0300 = Random/multiple cylinder(s) - misfire detected
C342D = ??not found??

P0016 - Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)
*You need to get this repaired as soon as possible!* This trouble code refers to the sensors reading the cam on the top of the engine and the crank shaft in the bottom of the engine. This helps keep the fuel mixture and fuel timing at it's best. The car's ECU is getting a bad reading from one or both of the sensors.

P0016 Crankshaft Position Camshaft Position Correlation Bank 1 Sensor https://www.autocodes.com/p0017_chevrolet.html

Crankshaft Position Camshaft position Correlation Bank 1 Sensor 'a'

EOBD II Error Code: P0016
Description:
Crankshaft Position (CKP)/Camshaft Position (CMP), Bank 1 Sensor A - Correlation
Indication:
Malfunction Indicator Lamp (MIL) ON.
Solutions:
Wiring.
Crankshaft position (CKP) sensor.
Camshaft position (CMP) sensor.
Mechanical fault.
Timing Issue.
Camshaft Adjuster.

Checks:
Check Setting of Timing Belt.
Check Timing of Intake/Exhaust Cams.
Check Cam Adjusters as per Repair Manual.

P0016 Crankshaft Position - Camshaft Position Correlation
P0135 O2 Sensor Heater Circuit
P0138 O2 Sensor Circuit High Voltage
P0340 Camshaft Position Sensor "A" Circuit
P0344 Camshaft Position Sensor "A" Circuit Intermittent
P0508 Idle Air Control System Circuit Low
P0522 Engine Oil Pressure Sensor/Switch Low Voltage
_____________--
JMA TRS-5000 Cloning Machine

P0016 Crankshaft Position/Camshaft Position Correlation Bank 1 Sensor A
take the engine out ,someone having a laugh at your expense or what

P0010....'A' Camshaft Position Actuator Circuit (Bank 1)

P0011....'A' Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)

P0012....'A' Camshaft Position - Timing Over-Retarded (Bank 1)

P0013....'B' Camshaft Position - Actuator Circuit (Bank 1)

P0014....'B' Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)

P0015....'B' Camshaft Position -Timing Over-Retarded (Bank 1)

P0020....'A' Camshaft Position Actuator Circuit (Bank 2)

P0021....'A' Camshaft Position - Timing Over-Advanced or System Performance (Bank 2)

P0022....'A' Camshaft Position - Timing Over-Retarded (Bank 2)

P0023....'B' Camshaft Position - Actuator Circuit (Bank 2)

P0024....'B' Camshaft Position - Timing Over-Advanced or System Performance (Bank 2)

P0025....'B' Camshaft Position - Timing Over-Retarded (Bank 2)

I think your sensors are pattern parts and the readings /resistances are not the same as the original parts ,try some bosch units is my first suggestion ,

P1699 is code specific, P0016 is cam/crank positioning correlation sensor A - bank 1. B1900 is code specific too. I will try to get you more info Monday.