Question about 1994 Mercury Villager

1 Answer

94 mercury villager van, passenger auto seat belt motor running continuously & seat belt won't work. Drained battery. Where is the fuse located?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 252 Answers

Engine compartment main fuse panel 30 AMP fuse Fuse #4 scroll down and look at this diagram picture on this link. http://www.autogenius.info/mercury-villager-1st-generation-1993-1998-fuse-box-diagram/ caution, this fuse runs power seats, windows and sun roof as well.

Mercury Villager 1st Generation 1993 1998 fuse box diagram Auto Genius

Posted on Nov 15, 2016

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
shaggyrat

Christophe Thompson

  • 1224 Answers

SOURCE: Rear seat removal 2000 merc Villager

fold top seat down first
then there is seat clip push seat forward with upward motion
this releases back floor clamps once released pull seat back this releases the front clamps then pull seat out of back door

Posted on Jul 07, 2008

Anonymous

  • 405 Answers

SOURCE: Fuse Diagram

d34dbde.png
This should help you.

Posted on Dec 27, 2008

emissionwiz

Marvin

  • 85206 Answers

SOURCE: location of the engine diagnostic connector 1995 village mercury

The diagnostic connector is located on the engine near the starter. However, there are four connectors in that location and without pictures it would be difficult to determine which is the proper one

Posted on Mar 08, 2009

Richard Scordino

  • 6982 Answers

SOURCE: Jeep Grand Cherokee passenger power seat quit working

no problem...That's what it's all about...small victories every day...
Good luck with your jeep!!!

Posted on Apr 20, 2009

sidlas

tomas sidlauskas

  • 95 Answers

SOURCE: where is the nork sensor on mercury villager 1999

the knock sensor is under intake, must remove intake and it is under two coolant lines

Posted on Jun 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is crankshaft pisition sensor for 1995 mercury villager


1995 Mercury Truck Villager Van 3.0L EFI SOHC 6cyl

The Crankshaft Position Sensor is located: Under hood, passenger side, lower engine area, front of crankshaft pulley, mounted in engine block.

Jul 22, 2015 | Mercury Cars & Trucks

2 Answers

Need diagram for 1995 Mercury villager 3.0 to change timing belt


that engine is built by nissan believe it or not. look on the net for your van or a nissan maxama. I just googled it and found lots of diagrams for that van(95 mercury villiger 3.0 timing belt diagram. I would not only replace the belt, I would replace it using a timing belt replacement kit.If your going to keep the van.

Nov 17, 2011 | Cars & Trucks

1 Answer

Passive retraints on both diver and passenger side stopped working at the same time. The fuse if fine. I assume that the motor has gone out and needs to be replaced. Is my assumption correct? If...


Each shoulder belt has its own motor, so it's not a motor issue. The motors are in the panels by the 2 nd row seats.

Go to our site and read the files on this and the pics i put there showing what it looks like.

http://groups.yahoo.com/group/villagerquest/

gerry

Jan 30, 2011 | 1993 Mercury Villager

1 Answer

The motor for the front seatbelt wont stop. Is there a fuse to stop it?


There is a connector that provides power to the seat belt motor/sensor in the doorpost (passenger side) or behind the LH wall molding (driver side).
Not sure where the stop sensor is, but I think part of the drive track assembly.

I chose to replace the drive track assembly on my driver side when it was sticking / cutting out in cold weather.
Seat belt drive track

Sep 18, 2010 | 1995 Mercury Villager

1 Answer

Info . on the motor


not an interference motor. change the timing belt to fix.

Just be sure it's not the fuel pump or distributor first.

Check for brown dust under distributor cap & rotor. If yes, replace distributor. Ebay for part.

go here for more help

http://autos.groups.yahoo.com/group/villagerquest/

Apr 14, 2009 | 2001 Mercury Villager

1 Answer

Power seat not working


go here for help

http://autos.groups.yahoo.com/group/villagerquest/

Circuit Protection
Power is supplied to the seat motors through the 30A POWER WINDOW fuse. The fuse is located in the LH engine compartment fuse junction panel and is hot at all times. The circuit breaker is behind the interior fuse junction panel and prevents current overload and component damage.

Mar 28, 2009 | 1998 Mercury Villager

1 Answer

Rear Air & Heat does not work on '97 Mercury Villager.


It's probably the cracked solder joint on the control assembly in the frony. I fix them all the time and sell them for $30 plus shipping. I always keep a spare repaired in my garage. villagers & Quests are noted for this. Don't know why you don't have lights on rear panel. I keep a spare one of those too, but it should have no affect on heater performance. Let me know if you are interested. You have to send yours back to me though.

If you are a techie, I will refer you to our Villager forum where there are files and photos on everthing about Villager & Quest issues.

http://autos.groups.yahoo.com/group/villagerquest/


see the circleed area where the bad solder joint is on the backside of the control head.

505a8c0.jpg

snorkelbobby@gmail.com

Mar 06, 2009 | 1997 Mercury Villager

2 Answers

1991 CIVIC LX AUTOMATIC SEATBELTS NOT WORKING.


I had a problem on a 91 Civic DX where the drivers auto seat belt wouldnt move and the beeper would not stop.Had a blown seat belt fuse.Replaced the fuse no more problem. The Seat belt fuses are located under the red cover that covers the positive battery terminal. On mine the fuse closest to the font of the car was for the drivers side auto seat belt the one closest to the windshield is for the passager seat belt. They are green and rated at 30A.

Nov 08, 2008 | 1991 Honda Civic

1 Answer

Seat Belts/Front Seats


seats use heavy corrent & use relays instead of fuses. check relays in fuse panel. see chart on cover or owner manual for location.

Also, this is for 96 villager seats.

Circuit Protection
Power is supplied to the seat motors through the 30A POWER WINDOW fuse. The fuse is located in the LH engine compartment fuse junction panel and is hot at all times. The circuit breaker is behind the interior fuse junction panel and prevents current overload and component damage.

go to this site for more help

http://autos.groups.yahoo.com/group/villagerquest/

Aug 24, 2008 | 1994 Mercury Villager

Not finding what you are looking for?
1994 Mercury Villager Logo

Related Topics:

592 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

gerry bissi

Level 3 Expert

4388 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

fordexpert

Level 3 Expert

5692 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...