Location of BCM module on a 2007 Impala - 2007 Chevrolet Impala LS Sedan New Cars

no body size told, extended cab or ????
ext cab is
BCM should be located on passenger side kick panel (under glove box to the right). You have to remove a panel.
2007 service manual remove it page, clear as day

Body Control Module (BCM)
At the right side of the I/P, under carpet in footwell area

Doesn't have a BCM . Has Door modules an LCM - lighting control module . If you list the problem you are having we can help.

BCM 3 fuse #4 30 amp - under hood fuse box . Plus there is a relay HVAC relay 30 - location -body control module . The BCM is located under right side front - center console

there is no flasher on that car, the BCM (Body Control Module) controls your turn signals. the underhood fuse box is a common failure item that will take out your turn signals.

You won't find it because........there isn't one. The BCM (body control module) controls the flash. If you have no sound it could be a defective speaker.

2007 Scion tC Body Control Module - 1A Auto

www.1aauto.com > 2007 Scion tC

Shop at 1A Auto for a brand new Body Control Module (BCM) replacement for your2007 Scion tC at a great price. 1A Auto has a large selection of Body Control ...

HELP!!! BCM issue 2005 tc - Scionlife.com

www.scionlife.com/forums/scion-tc.../help-bcm-issue-2005-tc-165745/

Jun 30, 2009 - i think i have a possible BCM (body control module) issue with my 05 tc, ... Using 2007 Air Box in a 2005 Scion TC, chowdahound, Scion tC 1G ...

2007 Scion Tc Body Control Module - Auto Parts Discounter

EPS/STR WHL CNTRL fuse #19 2amp , location, the BCM .
Body Control Module (BCM)
Under the I/P below the radio on the right side of the center console
Is your air bag light lit ? If so it's not a fuse issue !

Not likely

Doubt it did fail

They just have not found a problem yet

First off you need to read how this works . BCM - body control module is in fail- safe mode more then likely . The ingition switch is a input to the BCM . The BCM turns on relays to turn vehicle systems on . If something happens the system will fail safe to last commands by the BCM .
The body control system consists of the body control module (BCM), communications, and various input and outputs. Some inputs, outputs and messages require other modules to interact with the BCM. The BCM also has discrete input and output terminals to control the vehicle's body functions. Battery positive voltage is provided to the BCM from the BCM fuse in the underhood fuse block. The module has two grounds at G 202 as well as one directly to the vehicle battery. The BCM is wired to the GMLAN High speed serial data buss and the GMLAN Low speed serial data buss and acts as a gateway between them. If the BCM does not communicate the vehicle will not start due to the inability of the engine/powertrain control module (ECM/PCM) and vehicle theft deterrent (VTD) control module to communicate without the BCM providing the gateway function.
Power Mode Master
This vehicle body control module (BCM) functions as the power mode master (PMM). The ignition switch is a low current switch with multiple discrete ignition switch signals to the PMM for determination the power mode that will be sent over the serial data circuits to the other modules that need this information, and so the PMM will activate relays and other direct outputs of the PMM as needed. Refer to Power Mode Description and Operation for a complete description of power mode functions.

Relay Controlled Power Mode
The body control module (BCM) uses the discrete ignition switch inputs Off/Run/Crank Voltage, Accessory Voltage, and Ignition 1 Voltage, to distinguish the correct power mode. The BCM, after determining the desired power mode, will activate the appropriate relays for that power mode.
The RAP relay remains on for a timed period after the Ignition key is removed. Refer to Retained Accessory Power Description and Operation for more information on the retained accessory power (RAP) function.

You mite want to thing about taking your vehicle to a qualified repair shop. Hooking up a professional or factory scanner to view input data to the BCM ,plus checking for DTC'S - diagnostic trouble codes in the BCM , autozone , advance part stores can not read codes in the BCM .