Can't start my 2001 mdx with remote starter screen showing fuel average heating fan comes on only when I press brake padel rear wiper on off it self

You will have to first check the wiper motor relay in case it has become fused and stuck.
After that, then you need to check the switch operation on the wiper stalk.

Checc your asd relay. Mine was doing same thing and asd relay would open then shut immediately. Turn key to on pos then pull relay when you put it bacc in you will feel it open then close right away. If so your camshaft or crankshaft pos sensors are most likely the issue. Checc fuel line if fuel line shuts down it is your asd I believe most def

RL1 Front Wiper Control Relay RL2 ABS Power Relay RL3 Air Suspension Power Relay RL4 Right Heated Front Screen Relay RL5 Left Heated Front Screen Relay RL6 Auxiliary Power 1 Relay RL7 Auxiliary Power 2 Relay RL8 Front Wiper Interval Relay RL9 Horn Relay RL10 Spare Relay RL11 Headlamps Wash/Wipe Relay RL12 Fuel Pump Relay RL13 A/C Condenser Fan 1 Relay RL14 A/C Condenser Fan 2 Relay RL15 Ignition Relay RL16 Starter Relay RL17 ABS Pump Relay RL18 A/C Control Relay RL19 Engine Main Control Relay RL20 Air Suspension Compressor Relay

Hope this helps your out. I know the diagram and locator is a bit blurry but hopefully it gets what you need.
Drivers kick panel:
Front wiper 20A - Front wiper system Cigar 15A- Cigarette lighter Audio 10A- Audio, remote control mirror Air Bag 10A -Air bag diagnostics Stop lights- 15A -Rear brake light, high mounted stop light ECU B+ 10A - Shift lock actuator, transaxle controle module, radio, engine control module Room 10A - Interior light, clock, ignition key reminder, rear cargo area light switch ABS 10A- Anti lock brake system control unit ECU IG1 10A - Transaxle control module, shift lock actuator, ABS control unit, DRL unit Meter 10A - Instrument panel, back-up switch, electronics time control module, inhibit switch Turn signal 10A- Hazard switch ,front and rear turn lights, turn indicator IGN1 20A - Ignition switch ABS 30A- ABS pump motor TNS 30A- Tail light, license plate light COOL/FAN 30A- Cooling fan Cond/Fan 20A- A/C condenser fan Starter 15A- Start signal , Fuel pump Blower 25A- Blower Motor SR/ACC 10A - Ignition switch Hazard 15A - Hazard and turn signal light D/Lock 25A- Door locks ABS 30A - Anti lock brake system control P/W RH 20A- Power window motor right hand P/W LH 20A- Power window motor left hand IGN2 25A- Ignition Switch
Engine compartment :
Head 25A- headlights IG 2 30A- Ignition switch IG coil 15A -Ignition coil, condenser,generator IC regulator, diagnostic connector. O2 down 10A- Rear O2 sensor O2 up 10A- Front O2 sensor Fuel pump 10A -Fuel pump unit Injector 10A -Fuel injector ,camshaft positioning sensor, purge solenoid valve, EVAP, IAC actuator, Mass Airflow sensor, EGR stepper motor. fuel pump relay coil, vehicle speed sensor. A/Con 10A - A/C compressor controls, cooling fan BTN 30A- Brake light , high mounted stop light. Tail light LH 10A- License plate light, tail light , rear combo light, instrument panel illumination Tail light RH 10A-License plate light, tail light , rear combo light, instrument panel illumination Head low 15A- Headlight Head Hi 15A-Headlight Horn 15A- Horn

Inside kick panel

have you checked the relay? or the ground or positive wires shorted out and may need replaced.

Here's an excerpt from the 2002 Acura MDX 4WD 6cyl Repair guide for replacing what the reference manual calls the "control assembly" - its located under the console rear trim and may (or may not)
contain the blower resistor - my manual doesn't say - but this is the closest thing I could find for you. Every other blower resistor I've had to find was located close to the heater controls - and this
car seems to be no exception -- its heater controls are located in the console between the seats, rather than in the dash (as in Acura 2003-06 MDX models).

You may want to call your friendly Acura dealership ad speak to the parts department, to make sure where the blower resistor is located - or a visit to a dealership parts counter often (or
Advance Auto Parts is helpful too) ofen clarifies questions I have from Haynes manuals (the cheapest car repair guides).

All this assumes that you've correctly diagnosed your blower control problem -- as in "replace the blower resistor when the blower works only on the MAX/Highest setting."

-- begin excerpt from 2001-2 Acura 4wd 6cyl MDX Repair manual --
Control Assembly Removal & Installation

2001-02 Models

1. Remove the console rear trim. Refer to the accompanying illustration.
   
   

   Fig. Exploded view of the console rear trim
   

2. Remove the self-tapping screws and the rear heater-A/C control unit (A) from the console rear trim (B).

To install:

1. Install the control unit in the reverse order of removal. After installation, operate the control unit controls to see whether it works properly.
2. Run the self-diagnosis function to confirm that there are no problems in the system.
   
   

   Fig. Remove the self-tapping screws and the rear heater-A/C control unit (A) from the console rear trim (B)
   



--- end excerpt from 2001-2 Acura 4WD MDX 6cyl Repair Manual ---

Try removing the battery for half an hour or so and then reconnecting (check you have all your radio codes etc before you do this).

Check you switch, resistor (if so equipped), and wiring for a bad connection, corrosion, or short.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/sean_54c3a3dc48a7773c

maybe the fan itself is the problem, it could be a carbon brush problem,,,try to tp the motor while it is on, if it runs, then the brushes are short already...

i hope i was able to help

tnx,

drcool

pls rate me